Precautions on Zipper UseMetallion®, Combination Zippers, Clear Coil ZipperCautionary Notices for Washing and Dry CleaningCoil zippers, where dyed tape is stitched to the Metallion®, Combination or Clear Coil elements, are moreprone to twisting in comparison to standard coils when being subjected to high-temperature drying duringwashing and dry cleaning.Supported Items Combination Zipper Clear Coil Zipper METALLION® (COMB- ) Precautions on Zipper UsePlease be aware of products with different tape, element and stitching colors. Metallion®, Combination Zippers, Clear Coil Zipper Cautionary Notices for Washing and Dry CleaningTwisted Condition Reproduction Test via Dry Cleaning Twisting has occurred Impossible to restore No twisting Section dry-cleaned Section dry-cleaned with the zipper open with the zipper closed■A lways close the zipper during washing and dry cleaning, and set the temperature to be under 100℃.※Depending on the shrinkage rate of sewn material, the conditions will change slightly. 49
Precautions on Zipper Use Remarks for Clear Coil Zipper ● Specify petroleum-type drycleaning. ● T he crosswise strength of the tape is slightly lower than that of standard tape. ● Wash with water temperature under 40℃ to prevent the nylon transparent tape from shrinking. ● Iron covered with fabric, at a low temperature from 80℃ to 120℃. Remarks for VISLON® Transparent Type ● R ecommend petroleum dry cleaning only. ● Crosswise strength of chain is a little weaker than that of standard item, therefore it is not recommended for an application which requires stronger chain strength. Precautions Remarks for Clear Coil Zipper / Remarks for VISLON® Transparent Type / Proper Use / Sewing of 3CF Open-End Zippers and Two-way Open Proper Use / Sewing of 3CF Open-End Zippers and Two-way Openon Zipper Use ● 3CF open-end & two-way open zippers are designed for thin and light fabric. To ensure light weight, the open parts of this product are made of plastic, so their strength is relatively low (about half of 5CN, which is generally used in the front opening of general garments). ● As such, please avoid using this product in heavy knit garments, with thick fabric, or where a strong force may be applied during garment use. Strong pulling or twisting could result in the breakage of the parts. Do Not twist the open parts. Also please note the following precautions for proper handling in order to avoid unnecessary damage or breakage. 1 Zipper Operation ◆When Closing Close Close 1. Make sure the slider is positioned next to the box. 2. Completely insert the pin into the box end. 3. Pull up the slider. ◆When Opening Separable Open Slider 1. Pull the slider all the way to the open parts. Pin Open 2. Draw the separable pin out. Box 2 Ironing 1. Completely close the zipper and cover with a piece of fabric. 2. Ironing temperature should be below 130℃. 3. Be careful not to accidentally iron the plastic parts. 3 Sewing ) Sew outside the yellow line. ( Do Not sew on the plastic part. Sew outside50 Yellow Line
Precaution for Zipper Sewing Proper Sewing Procedure for ZippersSpace for Slider The slider needs some room to move for the zipper to work.If the stitch is made right by the edge of the elements, the slider will easily catch the adjacent fabric.Please make sure to allow enough space for slider operation.Lining fabric especially gets easily caught in the sliders, so sew on the part away from the elements andsecure the edges with sewing machine or prick stitch if a lining is used. Allow enough space for slider operation. Precaution for Zipper Sewing■Sewing Long ZipperTo confirm the compatibility between the fabric and the zipper, tack the zipper before actually sewing on the Proper Sewing Procedure for Zippersfabric and check their elongation and so on.Knit fabric especially requires this preliminary check.■Sewing onto Shaggy Fabric (Fur, Shaggy, etc.)When applying zipper onto shaggy fabric, place cover fabric such as leather at the edges in order to prevent theslider from catching the fabric.■Sewing Zipper on Pants FliesSaddle stitch can reduce the burden on the bottom stop.Pants using a short zipper or tight-fitting pants especiallyplace great burden to the stop, so applying the saddle stitchis strongly recommended.Saddle stitch Slider Bottom Stop Saddle Stitch 51
Precaution for Zipper Sewing Sewing CONCEAL® (Closed-End) Zipper onto Fabric Prepare a zipper approx. 30mm longer than the actual garment opening. Welded Zipper Length 12mm bottom stop Movable Bottom Stop Sewing Needle Actual CONCEAL® Opening Length Zipper 30mm Opening End Point Garment Body Fabric Sewing Machine Foot For CONCEAL® Zippers Movable Bottom Stop Precaution for The movable bottom stop is provided to prevent fraying of the fabric at the opening end. Fraying byZipper Sewing the slider movement can be prevented by fixing the stop about 5mm above the opening end point with a special sewing foot.Sewing CONCEAL® (Closed-End) Zipper onto Fabric Body A When the opening end is already sewn Body A (front side) Body A (front side) Body B End Point Markings (reverse side) Marking Opening End Point 1) Place Body A and B together and sew Body B Body B to the opening end point. 1) Put together the body fabrics and 1) Pull down the slider to the bottom stop, then sew on both sides of 2) Make sure to backstitch at the end point. the zipper, then mark the end point the zipper, making sure both markings are met. 3) Mark the end point on the fabrics. on the zipper. 2) Use the YKK sewing machine foot, raising the element up and fitting it in the groove of the foot. Space Body Movable 5mm Opening (reverse side) Bottom Stop Body End Point (reverse side) Body (reverse side) Zipper Stitch Line Body (reverse side) 1) Sew on the zipper to the opening end point. 1) Bring the slider pull-tab out to the front 1) Position the movable bottom stop about 5mm above the opening 2) Backstitch the beginning and the end of the stitch. side, then close the zipper. end point, then secure it using the special jig. Do not cross the zipper stitch lines with the body 2) The stop prevents the fabric at the opening end from fraying. stitch line; leave room for the slider pull-tab to pass through.52
Precaution for Zipper SewingWhen sewing the opening end after attaching the zipper to the bodies Body A Body A (front side) Body A (front side) Body B End Point Markings (reverse side) MarkingOpeningEnd Point 1) Mark the end point of the 1) Put together the body fabrics and the 1) Pull down the slider to the bottom stop, then sew on both sides of opening on the fabrics. zipper, then mark the end point on the zipper. the zipper, making sure both markings are met. Body Zipper Stitch Line 2) Use the YKK sewing machine foot, raising the element up and(reverse side) fitting it in the groove of the foot. Opening End Body Point 3) Backstitch the beginning and the end of the stitch. (reverse side) Zipper Foot 1) After sewing both sides of the Movable 5mm Precaution for zipper, close the zipper, ensuring 1) Sew together both bodies using the ordinary zipper Bottom Stop Body Zipper Sewing the pull-tab comes on the body front foot below the opening end point. (reverse side) side. Backstitch the beginning and the end of the stitch. Body (reverse side) 2) Both stitch lines (above & below the end point) should be aligned. 1) Position the movable bottom stop about 5mm above the end Sewing CONCEAL® (Closed-End) Zipper onto Fabric/ Precautions on Sewing CONCEAL® (Closed-End) Zipper point, then secure it using the special jig. 2) The stop prevents the fabric at the opening end from fraying. Precautions on Sewing CONCEAL® (Closed-End) Zipper■When CONCEAL® zipper is used in a tight-fitting garment such as a dress. The elements inside the garment may scratch against the user's skin. 裏の画像The dress turned inside out Bottom end of the elements Scratch against a user's skin May raise the nap of undergarments■Please wrap the part below the movable bottom stop in a fabric backing or put a patch to prevent the elements from scratching against the user's skin. Fabric Backing Put a Patch 53
Precaution for Zipper Sewing Sewing CONCEAL® (Open-End) Zipper 3CH Sewing on the Retaining Box Side Pull up slider Sew 2mm Sewing on the Separable Pin Side and retainer box away from • Start sewing from the top of here the elements • Start sewing from the top of the zipper using the YKK Approx. the zipper using the YKK sewing machine foot, to about sewing machine foot. 30mm from the bottom stop. 30mm • At least 15mm from the • Pull up the slider and the bottom stop, switch to a retainer box at approx. 30mm narrow foot and sew at least from the bottom, and then 2mm away from the elements continue sewing beside the to the bottom. element edge. Sew Pull up slider and At least At least Sew the edge the edge 15mm 2mm up to here At least 15mm retainer box at approx. 30mm Approx. from the bottom 30mm Precaution for Attention AttentionZipper Sewing Preferred sewing conditions Sewing on the very edge of the Sewing Pitch: 2.5mm insert pin may make it difficult to Backstitch: 1 backstitch insert the pin into the slider.Sewing CONCEAL® (Open-End) Zipper Sewing pitch that is too small and repeated backstitches will cause the tape to break. 5CH Sew at least 3mm away from the Sewing the Retaining Box Side / Separable Pin Side elements. Using the YKK sewing machine foot, sew At least 19 20mm right beside the element edge until the 20mm point approx. 19 20mm from the bottom. Sew the edge up to here 19 20mm Switch to a narrow foot and move slightly (over 3mm) away from the elements, then continue sewing to the bottom. At least 3Amt lmeast Attention 20mm Sewing the very edge of the open parts may cause the open parts to break.54
Precaution for Zipper Sewing Precaution for Precautions for sewing Coil Zipper Zipper Sewing■During the spacing process of the coil zipper production, elements are cut and removed from the zipper Precautions for sewing Coil Zipper tape. Occasionally, a half element (remaining after cutting) may be left behind next to the top stops of the zipper, and such cut element may be protruding if the top extension of the zipper tape is bent closely to the top stops during the garment sewing processes.■The sharp cut end of the protruding element may scratch a user/consumer. ■The top extension(s) of the zipper tape should be bent at least 5mm away from the first element (at the top stop position). This would prevent the elements from protruding. ■Selecting the P-TOP (plastic top stops) products can prevent the exposure of sharp cut element, and is highly recommended for infants' / kids' garments. 55
Precaution for Precaution for Zipper SewingZipper Sewing Warnings and Requests when Sewing the P-TOPWarnings and Requests when Sewing the P-TOP ■W hen stitching the zipper, if the sewing machine attachment or feed dog comes in contact with the top stop and damages it, it could create a jagged edge which can lead to injury. Example of such damages: VISLON®（NEWKOB4）damage example Coil zipper (P-TOP) damage example ■P lease be mindful that the sewing machine attachments or feed dogs do not come in contact with the top stop when sewing near the top stop or the top extension. 56
Precaution for Zipper Sewing Caution When Sewing PRIFA® Zipper■The threads in the printed section could protrude or shift when the rail edge of the slider interferes with the tape.Standard Position When the thread is misalignedWhen sewing PRIFA® zipper, the tape thread may get misaligned if excessive force is applied onthe print part by the bend created by the slider.The cause of the tape thread's misalignment: Precaution forWhen sewing with the zipper opened, a sewer will need to move the slider as they sew. Zipper SewingThe slider will not move smoothly if the stitchings are too close to the elements, and the rail edgeof the slider will interfere with the tape, leading to floating or misaligned thread on the print. Front Back Rail edge Caution When Sewing PRIFA® Zipper①Please select an area for proper stitching that allows for smooth slider operation.②When moving the slider, please raise the sewing machine foot. ・In particular, the slider rail edge may interfere when closing the zipper. Raise the sewing machine foot AttentionPlease refrain from using fixtures such as perforators when moving the slider, as it may causepaint and chrome plating to peel off or create sharp edges. 57
Zipper Problems and Solutions Q & A #Q A ●When using thick materials, please use zippers above No. 4. I used the No. 3 zipper with a thick material, which caused 1 punctures and breakage in the open parts. 2 The zipper open parts broke. ●For open-end zippers, confirm that the separable pin is firmly inserted when raising the slider. Is there anything in particular ●The 3CF has fine elements, so even if the separable pin is not inserted firmly into to be cautious about with the the box, it is possible to pull up the slider by force, in some cases damaging the open-end No.3 coil zipper open parts rib support. This is especially the case if the fabric around the separable 3 (3CF)? pin is ribbed, making it difficult to operate, or the zipper is long, making it difficult to see the ends while operating it. ●When sewing, do no sew over the open parts rib support. The front zipper of a garment ●Use an automatic slider (DA), which locks when not operated. 4 comes down on its own. ●U sing a pull-tab that is too big or heavy could lead to the slider being unlocked or breaking while walking. Post-processes such as ●We recommend YG type and GS type zippers, which have superior durability to washing or bio-stonewashing post-processes. Among the element colors, be particularly cautious of GK, GKB, 5 discolor or corrode the zipper, GTH and GDS. damage its slider or cause it to transmit its color. ●In order to avoid secondary damages from the residual chemicals used in post- processes, make sure to adequately neutralize, rinse and dry quickly. The zipper used on wool and ●Wool and feathered products are susceptible to residual chemicals such as bleach, feathered products changed causing the metal part of the zipper to react and become discolored or corroded 6 color. in storage. Neutralize adequately, and select items not easily susceptible to the influence of residual chemicals such as VISLON® zippers and coated sliders. Zipper Problemsand Solutions Q & A The metal part of the zipper ●Metal parts may corrode depending on the storage condition. There is a risk of the was discolored. corroded parts staining the product, so products should be kept at low humidity, 7 avoiding hermetically sealed storage in plastic bags or cardboard boxes and allowing some breathability in storage (please be aware of the influence of NOX as well). ●In regard to the use of rubber bands to tie zippers together, the sulfur components in rubber bands can cause the elements to corrode or discolor, or cause the tape to turn yellow, so do not use them. (This problem occurs even when the rubber band is used over a plastic bag.) ●T he use of cleaning products containing fluorine, or contact with fabric on which such cleaning products has been used causes metal parts to be discolored. Please be cautious of this. ●We recommend EVERBRIGHT®, which is comparatively resistant to discoloration. The part of the garment that is ●The element surface of the metal zipper is coated with lubricant. in contact with a metal zipper The lubricant itself is colorless and transparent, but the metal powder (element became dirty. shaving) created by opening and closing the zipper, as well as dust, etc. adhering 8 to the lubricant, may contaminate the fabric if these are transmitted along with the lubricant upon contact with the fabric. Be cautious when using metal zippers with light-colored fabrics or absorbent fabrics. When ironing (with steam in particular), be aware that the same effect may occur. ●For storage, line the parts that contact the metal zipper with paper. 9 Skin contact with the zipper ●Some elements and slider surface types contain nickel. Please select nickel-free caused an allergic reaction. products (special specification: N-ANTI). While sewing, the sewing ●The area around the top extension comes into contact with sewing machine machine needle or attachment needles and attachments from a variety of directions. In order to prevent damages, 10 damaged the top stop and lower the starting position of the zipper by 5mm and compare the result. (See p56) created a rough edge, causing injury. When opening and closing ●W hen sewing, if the stitching is made too close to the elements, the slider will not the zipper, it does not move have enough space to move, impeding its operation. Be careful to allow enough space 11 smoothly or catches the fabric. (See p51). ●If the zipper catches because the fabric used is too thin or soft, you should put in a stitch or core to reinforce it.58
Zipper Problems and Solutions Q & A#Q A ●The zipper tape is woven, so cutting the thread may cause fraying. Do not cut the12 The zipper tape tore from the sewing position and broke. zipper tape to reduce fabric pressure, to reduce interference from other parts, etc. The elements warped or ●When applying an iron to the zipper, be sure to cover it with fabric.13 melted when I ironed it. Be cautious of the zipper's heat tolerance (and the heat tolerance of the product itself). A VISLON® element has broken ●If you try to open a slider with lock function by force without using the pull-tab, the or cracked. elements may get torn off. When opening or closing the zipper, be sure to use the pull-tab.14 ●The material of the elements, polyacetal (POM), makes the elements susceptible to damage by strong acids. Do not clean the elements by soaking it in bleach, and if exposed to materials such as toilet cleaner or battery acid, be certain to wash it with water immediately. The zipper was bent in dry ●Repeated dry cleaning or high-temperature drying without closing the zipper will15 cleaning. cause it to bend. Be sure to close the zipper before washing, drying or dry cleaning. (See p49) The CONCEAL® no longer opens ●If the slider is pulled up diagonally, the elements will warp and disrupt the or closes. interlocking mechanism, and it will break if it is forced up further, making it impossible to open or close. When closing the zipper, first secure the button/hook,16 and pull up the slider along the elements so that it doesn’t get pulled diagonally. ●Z ippers are designed such that they are particularly hard to operate where fabric thickness changes, so do not use a CONCEAL® where fabric thickness changes. The seam of a coil zipper for a ●There have been instances where seams break due to repeated contact with other17 bag broke. parts of the bag, such as shoulder belts. Please be mindful when attaching other parts. Zipper Problems When using a pin lock (DP) slider ●Avoid the use of a pin lock slider, and use an automatic lock slider (DA) or non-lock and Solutions Q & A18 in my pocket, the protruding slider (DF) instead. part hurts. We used an automatic lock slier ●T he pull-tab of the slider may break when it gets stuck within the tumbler, and (DA type) for a product that goes chemical residue in the cover can corrode the slider. Please use the semi-automatic19 through a washing process, and the slider (GS), which is more durable and has a more suitable shape. slider broke. The paraffin melted from the ●The zipper elements are treated with paraffin in order to improve its sliding20 heat from an iron press and properties. When ironing areas directly touching the zipper, use a slip-sheet or fabric between a material and the iron. blemished the clothing material. Is there something I should be ●We provide special products for babies, such as the plastic top stop. Please contact21 aware of when using a zipper a sales representative. for baby products? The slider caught the material ●Try to pull the slider the other way, as to loosen the caught material. and tore a hole in it, or the ※This may cause the pull-tab to break, so do not try to force the slider to move.22 zipper won’t close because it Instead, try moving it gently. caught the material. When I sent my clothes off for ●W e have provided guidance to the cleaning industry to be careful with the sliders23 dry cleaning, the press broke when pressing. the slider. When I stored the zipper by ●T he sulfur components in rubber bands can cause the element to corrode, discolor or tying them with a rubber band, cause the tape to turn yellow. Please refrain from using rubber bands, and use paper24 the portion touching the rubber or cotton string instead. The same can occur for QUICKLON® as well. band changed colors. The color of the zipper rubbed ●Contact with plasticizers, adhesives and oils can cause the colors to rub off. Please25 off onto my bag. be particularly aware of PVC, synthetic leathers, resin coated fabrics, etc. ●Please store with a slip-sheet. 59
Snap Fastener Snap Fastener and Button Productsand Button Products Snap Fastener and Button ProductsSnap Fastener and Button Products: Three Basic Principles Three Basic Principles High Quality Products YKK products are made of highly qualified selected materials under strict production testing. High Performance Attaching Machine YKK has a variety of high performance attaching machines, from manual to programmed types. They all possess a compensator device. Please refer to page 66. Appropriate Technical Advice and Customer Service With skilled Field Technical Support members, called FTS, appropriate technical advice and follow-up service are available. 60
Snap Fastener and Button ProductsTack Button■ Special designs, personalized logos and variety of finishes are available. Closed Top Open Top Swivel Two Prong (Plastic Insert)Top PartsUnder Parts TC21 TC40 TC11 TC80Size 22LIGNE 24LIGNE 27LIGNE 30LIGNE 32LIGNE (13.9mm) (15.2mm) (16.8mm) (19.0mm) (20.3mm) Rivet & Burr TC40A Snap Fastener (Standard) and Button Products■ Special designs, personalized logos and variety of finishes are available. 10 12 14 15 18 Tack Button / Rivet & Burr LIGNE LIGNE LIGNE LIGNE LIGNE (6.4mm) (7.8mm) (9.2mm) (9.5mm) (11.4mm)Top Parts SIZEFront Pocket SIZEBurr SIZE SIZETubular SIZEBurr Under Parts Bull’s Eye TC40A-S Burr (Short) Capped Tubular Burr Washer TC40C Burr (Copper) 61
Snap Fastener and Button Products Snap ■ Special designs, personalized logos and variety of finishes are available. ■ Combination of top and under parts can be chosen from our lineup. 16 18 20 24 27 33 LIGNE LIGNE LIGNE LIGNE LIGNE LIGNE (10.1mm) (11.4mm) (13.0mm) (15.2mm) (16.8mm) (21.0mm) Top Parts SIZEStandard Type SIZE SIZECZ Flat Type SIZE SIZE SIZE CY Dome Type OT Open Type Snap Fastener S-Spring Snap Ring Spring Snap and Button Products ■ Applicable for light-duty to standard garments. ■ Applicable for standard to heavy-duty garments.Snap / S-Spring Snap / Ring Spring Snap Top Parts SNAP TOP UNSEEN CAP SNAP TOP UNSEEN CAP SW35 SOCKET SW65 SOCKET SK35 SOCKET SK75 SOCKET Under Parts SW35 STUD SW65 STUD SK35 STUD SK75 STUD SW35 POST SW35 CAPPED POST SW65 POST SK35 POST SK35 CAPPED POST SK75 POST ※Unseen cap is for hidden snap design.62
Snap Fastener and Button ProductsSNAPET®■ Special designs, personalized logos and variety of finishes are available.■ Dye-to-match to Prong and Cap are available. 12 14 15 16 17 18 19 LIGNE LIGNE LIGNE LIGNE LIGNE LIGNE LIGNE (7.2mm) (8.2mm) (9.5mm) (10.1mm) (10.8mm) (11.4mm) (11.7mm)Top Parts SIZEProng SIZE SIZEPearl SIZE SIZE SIZE SIZE Cap SOCKETUnder Parts STUD STUD PRONG POST Snap Fastener Prong is for knit and woven fabrics. Post is for woven fabric. and Button Products Cap VariationsPWM07 PWM08 PWM09 PWS05 PWS12 PWS19 PWS20 SNAPET® / Hook & Eye / Waist FastenerLINE STAR TOON NIRVANA ANCHOR STENCIL MARGARET LOTUS Hook & Eye Waist Fastener■ Suitable for slacks, dress pants and skirts. ■ Suitable for children's pants. HU10 WFTop Parts EYE Under Parts Top Parts Under PartsHOOK PLATE SB05-W WF HOLDERHOOK EYE PLATE WF HOOK SK35 POST 63
Snap Fastener and Button Products Eyelet Washer #200 #300 #500 #700 Eyelet Top Parts (7.8×4.0mm) (9.5×5.5mm) (11.5×6.0mm) (14.0×8.0mm) Under Parts Washer ■ Attachment to stretch fabrics is possible. ■ Pre-piercing is not required. Metal Sew-On Button ■ Light weight press button. ■ The hole is designed to prevent it from cutting the thread. ■ Special designs, personalized logos and variety of finishes are available. PQ IFG-R PQ-KN 10 STAR Snap Fastener 11.5mm 18.0mm 11.5mm 20.0mmand Button Products 11.5mm 13mm 15mm 18mm 18mm 18mm IBS-SEyelet Washer / Metal Sew-On Button PLAIN 11.5mm 13mm 15mm 18mm 20mm 13mm 15mm 18mm FUL 15mm PQ-PN 15.0mm 15mm 15mm Matte Color Special Color Finish Equal Color 3402 3412 3419 4311 4315 4316 431764
Snap Fastener and Button Products PLANCER®■ Metallic colors are available to match a METALUXE® zipper.■ Good for lightweight application. ■ Dry-Cleanable. ■ High Durability. ■ Self-Piercing. Top Parts PL-SZ PL-M PL-L PL-SZ 14 CAP PL-L 18 CAP PL-L 24 CAP PL-SZ SOCKET PL-M SOCKET PL-L SOCKET Under Parts PL-SZ STUD PL-M STUD PL-L STUD PL-SZ 14 CAP PL-L 18 CAP PL-L 24 CAP SOFIX® Snap Fastener and Button Products■ SOFIX® is a tape snap which has plastic injected directly onto the tape.■ No need for attaching machines.■ Combination of Socket-Stud tape is available. (Usage example: for comforters, to fasten the ends of the comforter cover.) PLANCER® / SOFIX®Standard Combination Fluorescent MetallicSnap Diameter: 8mm Width of Tape: 20mmSnap Interval: 15mm, 30mm, 45mm, 60mm, 75mm, 90mm Sales Unit: 50mStandard Colors: YKK Asian Group Color Card Special Colors: Dye-to-match is availableFor Babies For Sports Usage Examples For Comforters& Children Uniforms For Linings Other Garments 65
Snap Fastener and Button Attaching Machine Attaching Machine MODEL N-6 MODEL 131 The N-6 is a semi-automatic attaching machine with powered The Model 131 is a manual foot foot treadle, and it can be used press type for low-volume produc- with most YKK snap fastener tion, and it can be used with most items by changing the dies. Mark- YKK snap fastener items by chang- ing Light is equipped for easy ing the dies. positioning of attachment. Specifications Specifications Dimensions :1,000mmH×460mmW×425mmD Std. Equip. :Compensator Dimensions :1,080mmH×340mmW×450mmD Power :200W Motor MODEL N-7 Electric Source:100V or 220V Single Phase Weight :68kg This is an automatic model exclu- Std. Equip. :Compensator / Safety Device sively for Tack Button, Rivet Burr Marking Light or Eyelet Washer. Register type is also available to fix logo direction. MODEL N-8 This is an automatic model exclu- sively for SNAPET® or Snap. It comes in a set of two units, one for attaching prong and socket and the other for stud and post (or stud and prong). Specifications Specifications Snap Fastener Dimensions :1,340mmH×500mmW×560mmD Dimensions :1,340mmH×500mmW×500mmDand Button Products Power :300W Motor Power :200W Motor Electric Source:100V or 220V Single Phase Electric Source:100V or 200V Single Phase Weight :130kg Weight :110kg Std. Equip. :Compensator / Safety Device Std. Equip. :Compensator / Safety Device Marking Light / Marking Light /Attaching Machine Automatic Feeder(Register Type) Automatic Feeder / Gauge Plate MODEL N-8-3H MODEL N-8-4H This is an automatic model for This automatic model allows you SNAPET® which allows you to to program 4 components of SNA- choose the attachment order for 3 PET®. Combination of different component SNAPET®. surface finish of Prong with Socket and Prong with Stud can be registered. Specifications Specifications Dimensions :1,340mmH×500mmW×500mmD Dimensions :1,340mmH×500mmW×500mmD Power :200W Motor Power :200W Motor Electric Source:100V or 220V Single Phase Electric Source:100V or 220V Single Phase Weight :120kg Weight :130kg Std. Equip. :Compensator / Safety Device Std. Equip. :Compensator / Safety Device Marking Light / Automatic Feeder Marking Light / Automatic Feeder Gauge Plate / Gauge Plate / Attachment Order Programming Attachment Order Programming66
Ball ChainMetal Ball ChainYKK's ball chains are made of stainless steel material.Because of their functional and fashionable characteristics, ball chains are used in a variety of fields. Stainless (St.) BALL CHAINBall Size Material Ball Size Material 2.3 St. 4.0 St. 3.2 St. 4.5 St.Attachment Connector (CNA) Coupling B (CPB) Coupling C (CPC)※Depending on the size, the attachments can be shared.※Please use items that have appropriate properties for your desired uses.Plastic Ball ChainPlastic balls are attached to a nylon or polyester string, which is flexible, bends freely, and soft to the touch.Colors are standard and bright fluorescent. A two-tone color ball is also available with string and balls ofdifferent colors.Standard Color Variations Glow in the dark Color-Variations 055 80C1 M1 Ball Chain Metal Ball Chain / Plastic Ball Chain501 80C2 White504 80C3519 80C4 M2540 80C5 Green M3 Yellow M4 Blue M5 Pink560568580Attachment Connector (CNA) Reinforced Connector (CNA2) Coupling (CP)Size Variations Material 35BR D (outer・diameter) L (length) Unit: mm 35BR Cord Material Plastic Ball48BR 3.5 4.5 48BR Polyester Polyacetal58BR 4.8 6.2 P (pitch) 58BR Polyester 5.8 7.0 8.8 Nylon 73 12.0 13.5
Cosmolon ® Principle of Cosmolon® Engagement of Hook and Loop Hook Loop Standard Type Napped Type Cosmolon®（Hook and Loop Fastener) Elastic Soft Elastic Type Soft-Type 1QNE-N×2QNE-N 1QS-NCosmolon® Principle of Cosmolon® / Cosmolon®（Hook and Loop Fastener) Standard Type Soft Napped Type 1QNN-N×2QN-N 1QS-N×2QM-N 4QNN-N Adhesive Strength Durability Hook ※Please consult with YKK sales representatives about the loop used with 1QS-N. Loop Standard Hooked Type Injection or Extruded Type Standard Type Napped Type Excellent Injected molded Excellent Excellent in durability in various shapes to suite use in durability in engaging strength 74
Cosmolon ®Cosmolon®Cosmolon® Types and Uses Kind Material Features Main Uses Woven STANDARD type Nylon ■Fish hook-shaped pile for reliable engagement. ●Apparel 1QNN-N Nylon ■Uses a thick monofilament hook. ●B ags, pouches, shoes, gloves, belts, tool SOFT type ■Normal type Hook Tape (A) 1QS-N ■Fish hook-shaped pile for reliable engagement. cases,and sporting, leisure and amusement ■H igh-density pile with thin monofilament hook, goods. ●Handicrafts, interior decoration items softer to the touch, yet strong. ●T rims and seats of automobiles, trains, and airplanes (fire-resistant type)Cosmolon® (Hook and Loop Fastener) Polyester ■C ompared to nylon tapes, superior both in water ●M edical appliances such as corsets and resistance and UV-resistance. tonometers Injection POWERHOOK® Button Nylon ■Injected molded type hook in various shapes. ●Interior decoration items such as curtains 1Ql * *-* Polyester ■T he injected molded hook provides stronger shear ●Automobile-related items Continuous POWERHOOK® PP ●Daily necessities such as cleaning tools Injection 1QE * *-* PE and peel strength than woven hooks. ●Belts POM ■Continuous injected molded type hook. ●Industrial materials ■C ontinuous injected molded type hook pro- vides stronger shear and peel strength than woven hooks. Loop Tape (B) STANDARD 2QN-N Nylon ■Mates with all hook tapes. ●Apparel type ■Consists of bundled loop pile. ●B ags, pouches, shoes, gloves, belts, tool cases, Woven ■Provides higher shear strength. and sporting, leisure and amusement goods. 2QN-P Polyester ■C ompared to nylon tapes, superior both in water ●Handicrafts, interior decoration items resistance and UV-resistance. ●T rims and seats of automobiles, trains, and NAPPED type Nylon ■Mates with all hook tapes. airplanes (fire-resistant type) 2QM-N ■Consists of napped loop pile. ●M edical appliances such as corsets and ■Stronger peel strength than standard type loop. tonometers Woven MIXED type Nylon ■H ook and loop are mixed on the same tape. ●Apparel (ski wear, etc.) Mixed (AB) 4QNN-N ■N o distinction between the hook tape and the loop ●Gloves, belts tape. ●Beddings, interior decoration itemsSpecial Varieties of Cosmolon® WE Type Cosmolon® used in high-frequency welding onto soft PVC sheet.WE-T Type Cosmolon® used in high-frequency welding onto fabrics, textiles, etc.AD Type Cosmolon® with a double-sided adhesive tape on its reverse side for a temporary bond.ADN Type Cosmolon® with an acrylic-based adhesive on its reverse side for a temporary bond. ※1ADS Type Cosmolon® with a rubber-based adhesive optimized for low energy surface. General purpose. ※2HMPP Type Cosmolon® with a stronger rubber-based adhesive optimized for low energy surface, such as PP and PE.※1. ADN type is applicable to soft PVC, however the ADN can react with plasticizers, affecting bound strength.※2. ADS type and HMPP is easily affected by plasticizers within soft PVC. Please refrain from using ADS type and HMPP on soft PVC substrates. FP type Fire retardant hook & loop fastener which satisfies the U.S. Federal Automobile Safety Standards FMVSS-302. FA type Fire retardant hook & loop fastener which satisfies the U.S. Federal Aviation Specifications, FAA-23-853 (b)■Cosmolon® Sizes and Shapes Put-up : 25m and 50m on spool Cosmolon® Cosmolon® Widths : 16, 20, 25, 50 and 100mm Cosmolon® Strength Test Peel Strength Test Under conditions of 20 ×65 RH fastened length of 50mm Shear Strength Test 5cm Holder Holder 5cm 5cm Holder 5cm Holder ※Tests based on JIS-L-3416-2000 75
Plastic Plastic HardwareHardware Information concerning safe operation Carefully read the following information so you can make the best and safest use of our fastening products. YKK goes to great lengths to maintain the quality and safety of our products while making sure they are comfortable for our customers to use. Our sales staff is prepared to assist you in all stages of your product development projects, from planning to setting up specifications. Feel free to consult with them at any time. Caution 1. Our plastic hardware is developed for luggage, bags and apparel. If you use our product for any specialized use, and especially for one of the applications listed below, please contact your YKK sales representative. ① Personal flotation devices (PFD), baby carriers (baby sling) or any other applications which are subject to particular standards; ② stretchers, safety belts or any applications which are for weight-bearing; ③ child seats, wheelchairs or any applications for use to reduce movement; ④ hard hats or any applications which provide safety features. ⑤ If you intend to sell our plastic hardware to retailers or directly to consumers, please contact us in advance. The above list is provided by way of example and is not intended to be exhaustive. We cannot guarantee that a product is suitable for a particular application, and as such, you should always conduct your own tests. 2. Once our products are attached to other items, there may be approved ways to pack, store or ship them in order to ensure their continued high quality. For example, buckles should be correctly combined in order to avoid deformation, breakage or detachment. 3. Please contact your sales representative about the certification of Oeko-Tex standard 100 or others. When using our products, you should 1. Choose the right fastener for your application from our product line. Your YKK sales representative can help you understand the variety of our products, their sizes, strengths and specifications. 2. Select plastic hardware that is the appropriate size for the tape in your application. 3. Refrain from using plastic hardware that has been exposed to or is covered in dirt of any sort. Product damage or malfunction may arise if the plastic hardware is not clean. 4. Refrain from using plastic and metal parts in one unit because of the potential for product abrasion. 5. Refrain from using goods left outdoors for a long time. Exposure to the sun and other elements may cause product discoloration and/or quality deterioration. 6. Avoid using items that have been in contact with or near a heat source. Heat may cause product deformation and/or quality deterioration. 7. Refrain from using goods that have been in direct or indirect contact with chemicals. Check for residual chemicals on all parts of plastic hardware whether applied by YKK or coming from another source. 8. Refrain from using a product in a position that is subject to pressure, impact or abrasion, or other condition where product deformation and/or damage may result. 9. Only make your choice of YKK product after adequate checks have been made. The strength of YKK products depend on the materials used, its texture, the thickness of its webbing, the position of its weld line and other factors which you will need to take into account. For further information, please contact your YKK sales representative. 10. D ue to certain material combination, noise from friction may be possible. If silent operation is necessary, please contact your YKK sales representative for detail. Recommendations for using YKK Buckles 1. When fastening a buckle, insert the plug straight into the intended socket until you hear a clicking sound indicating the two parts are interlocking. Next, lightly pull on both parts to confirm that they have been completely fastened. Incomplete fastening may result in product deformation and damage to any article attached to the buckle, especially if the plug comes loose from the socket. If the two parts cannot be fastened together, check again for any foreign material. Do not try to force the plug into the socket. 2. Buckles should not be used in positions where they will be put under external pressure. 3. All plastic materials deteriorates over time. Buckles that have been used for a long time should be checked for damage, cracks, deformations and abrasions before each use. If any abnormalities are found, stop using them immediately. Use in such circumstances may cause further product damage and/or malfunctions. 4. Completely remove any foreign materials including dust, sand or mud from buckles before use. 5. Situations which involve the application of excessive pressure or impact to a plastic fastener, such as being stepped on, struck or thrown, will result in a lowering of performance. 6. We will not be held responsible for damage to the buckles or unauthorized modification of buckles. Material Properties 1. All of our products are limited by the properties and qualities of the materials used. 2. Some products have a weld mark (the line that forms when materials bond within its mold during production). The mark is not a defect, damage or crack. Please check the product carefully before using. 76 YKK is not responsible for any defects, injuries or damages caused by the misuse/misapplication or remodeling of our products.
Plastic Hardware LB-YC LB-YCD LB-YCS LB-YCT LM-YC LB-TSBuckleLB-TSD Sharpn'LocTM Sharpn'LocTM Sharpn'LocTM Sharpn'LocTM Sharpn'LocTM 2 Way Release LM-TS LB-RT LB-MP LB-EQ LB-LW LB-LWD2 Way Release 2 Way Release Flapped Buckle UL approved Rotatable Ultra-Lightweight Ultra-LightweightLB-LWS LM-LW LB-MV LB-MVD LB-MVS LB-MVW LM-MVUltra-Lightweight Ultra-Lightweight LB-LV LB-LVD LB-LVS LM-LV LB-WGLB-HE LB-HEDLB-WGD LB-WGS Lightweight Lightweight Lightweight Lightweight SHOCKONLOCTM LB-WG1 LB-WGD1 LB-WGS1 LB-PT LB-PTDSHOCKONLOCTM SHOCKONLOCTM SHOCKONLOCTM HAMMERLOCTM HAMMERLOCTMLB-PTS LB-PTA LM-PT LB-PTC LM-D / DB LM-DH / DHB LB-RHAMMERLOCTM HAMMERLOCTM HAMMERLOCTM HAMMERLOCTM Plastic HardwareThese fastening products are intended for the apparel and luggage industries, but technical assistance and support are available for users interested inother applications. 77
Plastic Hardware LB-RD LB-RP LB-RN LB-RND LB-X LB-XD LB-XC LB-RH UL approved LB-PC LB-LB CYBERLOCTM CYBERLOCTM Curved LB-RC LB-LS LB-RS LB-S Curved Curved Curved Minimal Minimal Thin LB-FR LB-F2 LB-FU LB-Q WB-S1 LB-FW2/FW WB-H Minimal Rotatable Suspender 3way Belt Buckle WB-HS WB-DA2 WB-DAH1 LA-CB LA-CBH LA-CN Cam LK-HC Buckle LK-DH1 Belt Buckle Belt Buckle Belt Buckle Hole LJ-H / HW LK-YC LK-YCS LK-TS I.D. Card Strap Holder Adjuster LK-EA LK-WG LK-WGS Sharpn'LocTM Sharpn'LocTM LK-LVS LK-WL LK-LV Plastic LOCWAVE TM Adjuster LOCWAVE TM Adjuster LOCWAVE TM Adjuster Lightweight Adjuster Lightweight Adjuster LOCWAVE TM AdjusterHardware LK-U LK-KU LK-E / EK LK-M LK-L LK-PT HAMMERLOC TM Adjuster UL approved Lockable Adjuster These fastening products are intended for the apparel and luggage industries, but technical assistance and support are available for users interested in other applications.78
Plastic Hardware LA-RH LA-PYB LT-K LH-E LT-TGLoop LA-S HAMMERLOCTM 3way-Loop LH-WJ LA-EJTri-Bar LH-WAdjuste Wedge Adjuster LA-AXA / AXB LH-SG LA-PS LN-SM LN-ASClip Piping-Slider Snap HookLN-M1S Attachable LN-ML LN-AR1 Smooth Rotate Smooth Rotate LN-RE LN-M2S LF-CH LF-HASmooth Rotate Smooth Rotate Smooth Rotate Swivel & Rotate Swivel & Rotate LD-ELN-SX LN-KH LN-ZR LN-Z LD-S D-RingLD-K LD-R Swivel & Rotate Swivel & Rotate LC05PS1 LC05PS3 LD-RE LD-TW Cord Stopper Twist Plastic Spring Plastic Spring Plastic Hardware 79
Plastic Hardware LC05PS4 LC05PS6 LC05PS7 LC05PS8 LC05PS9 LC05SR LC05KW Plastic Spring Plastic Spring Plastic Spring Plastic Spring Plastic Spring Plastic Spring Plastic Spring LC05HW LC05RW LC05KH LC05SL LC05SC LC05SB LC05WC Plastic Spring Plastic Spring Plastic Spring Plastic Spring Plastic Spring Plastic Spring Plastic Spring LC05WF LC05MS1 LC05MS2 LC05MS3 LC03MS5 LC03MW1 LC03MW2 Plastic Spring Metal Spring Metal Spring Metal Spring Metal Spring Metal Spring Metal Spring LC03MW3 LC03MW4 LC03MW5 LC03PE LR05E LR05T Cord End Ring Metal Spring Metal Spring Metal Spring Metal Spring LR05F LC05UG LC02US LC10US LC02UC LC02UH2 Cord Holder Sewable Sewable Sewable Sewable Sewable LC05EL WZ-CO WZ-SI / WZ05NI LZ05DLW LE03NK Zipper Cord End Cover Plastic Sewable ZIPCAP TM Outer-Cap ZIPCAP TM Innerer-Cap Key LockHardware LE05WA1 LE03WV LE03SN LE03WN LE03SV LE03CMT LE01STT These fastening products are intended for the apparel and luggage industries, but technical assistance and support are available for users interested in other applications.80
Plastic HardwareLE07CP LE03PC LE05CE LE03PB LE02PA IJ01SC Zipper Pull 5BS AABL 3BR NR06 3BR NR08 IC20RYBelt ClipAdjuster CP002A CP004ACord InsertPuller 1QiBD-E WE-DA1 LE-B LE-PWTape End POWERHOOK TM Tapeend POWERHOOK TM Button Sewable Plastic Hardware 81
Beware of Counterfeit Beware of Counterfeit YKK ZippersYKK Zippers 82
YKK Worldwide Network as of March 2016 | |Country / Region Location | Company name | TEL | FAXNORTH & CENTRAL AMERICAUSA Atlanta (East Region and FTC) YKK (U.S.A) INC. 1-770-427-5521 1-770-421-3624USA Rutherford (Northeast Region) YKK (U.S.A) INC. 1-201-935-4200 1-201-935-4033USA Dallas (Central Region) YKK (U.S.A) INC. 1-214-647-0499 1-214-647-0505USA 1-847-657-9295 1-847-657-9356USA Chicago (GMG) YKK (U.S.A) INC. 1-714-701-1200 1-714-701-1290USA 1-425-277-2503 1-425-277-2579USA Anaheim (West Region and GMG) YKK (U.S.A) INC. 1-502-839-6971 1-502-839-3166 Seattle (Northwest Washington and Oregon and GMG) YKK (U.S.A) INC. Lawrenceburg (Snaps and Buttons) YKK (U.S.A) INC.USA Oxford (Webbing) TAPE CRAFT CORPORATION 1-256-835-9045 1-256-835-6526CANADA Montreal (Headquarters and GMG) YKK CANADA INC. 1-514-332-3350 1-514-332-9140CANADA Toronto YKK CANADA INC. 1-905-738-7941 1-905-738-7948CANADA Winnipeg YKK CANADA INC. 1-204-633-9179 1-204-633-6179MEXICO Irapuato 52-462-623-8128MEXICO Mexico City YKK MEXICANA S.A. DE C.V. 52-462-623-8100 52-55-5803-0699MEXICO Torreon 52-871-707-0707GUATEMALA Guatemala YKK MEXICANA S.A. DE C.V. 52-55-5803-0690 502-6644-0645HONDURAS San Pedro Sula 504-2553-4427 YKK MEXICANA S.A. DE C.V. 52-871-707-0707 YKK EL SALVADOR S.A. de C.V. SUCURSAL EXTRANJERA, GUATEMALA 502-6644-0644 YKK HONDURAS S.A. 504-553-3164EL SALVADOR La Libertad YKK EL SALVADOR S.A. DE C.V. 503-2319-1100 503-2319-1190NICARAGUA Managua YKK EL SALVADOR S.A. de C.V. SUCURSAL EXTRANJERA, NICARAGUA 505-8986-1700 505-8986-1711COLOMBIA Medellin JEN COLOMBIA S.A.S. 574-322-9394 574-360-0070SOUTH AMERICABRAZIL Sao Paulo YKK DO BRASIL LTDA. 55-11-3066-1111 55-11-2168-4785 YKK ARGENTINA S.A. 54-11-4554-3333 54-11-4553-5095ARGENTINA Buenos Aires INDUSTRIA YKK (CHILE) LTDA. 56-2-2949-1800 56-2-2949-1820CHILE SantiagoEUROPE, MIDDLE EAST & AFRICANETHERLANDS Sneek YKK NEDERLAND B.V. 31-515-429-729 31-515-425-199 44-20-7448-1345UNITED KINGDOM London YKK EUROPE LTD. 44-20-7448-1333 44-1753-57-7727 47-66-85-58-60UNITED KINGDOM Slough YKK (U.K.) LTD. 44-1753-57-2222 46-33-416-550 358-9-759-78650NORWAY Oslo YKK (U.K.) LTD. YKK NORGE FILIAL AV 47-66-85-58-50 7-495-231-2810 3751 7-289-5557SWEDEN Boras YKK (U.K.) LTD. FILIAL, SVERIGE 46-33-418-180 45-97-155-449 370-5-233-6132FINLAND Helsinki YKK (U.K.) LTD. SIVULIIKE SUOMESSA 358-9-759-7860 353-1-466-0070 49-202-274-5516RUSSIA Moscow 000 YKK 7-495-325-3025 49-6182-805-70 49-5127-409350BELARUS Minsk 000 YKK BELORUSIA REPRESENTATIVE OFFICE 3751 7-289-5557 49-202-7493-446 48-468-570-701DENMARK Ikast YKK DANMARK A/S 45-97-155-388 380-44-461-9869 32-9-385-6520LITHUANIA Vilnius YKK POLAND SP. ZO. O. LITHUANIA OFFICE 370-5-213-3227 33-1-40-89-6222 420-531-015-415IRELAND Dublin YKK (U.K.) LTD. IRELAND BRANCH 353-1-403-5959 43-2626-62460 36-1-452-7231GERMANY Wuppertal YKK EUROPE LTD. TRANSPORTATION FASTENING MATERIALS 49-202-274-550 40-21-408-71-99 385-13-872-559GERMANY Mainhausen YKK DEUTSCHLAND GMBH 49-6182-805-0 381-21-473-9412GERMANY Harsum DYNAT VERSCHLUSSTECHNIK GMBH 49-5127-40930GERMANY Wuppertal YKK STOCKO FASTENERS GMBH 49-202-7493-0POLAND Mszczonow YKK POLAND SP. ZO. O. 48-468-570-700UKRAINE Kiev YKK POLAND SP. ZO. O. 380-44-461-9867BELGIUM Nazareth(EKE) YKK FRANCE SARL 32-9-385-5751FRANCE Paris YKK FRANCE SARL 33-1-40-89-62-00CZECH Modrice YKK CZECH SPOL. S R. O. 420-531-015-400AUSTRIA Marz YKK AUSTRIA GMBH 43-2626-62405HUNGARY Budaors YKK AUSTRIA GMBH HUNGARY OFFICE 36-1-452-7232ROMANIA Bucharest YKK ROMANIA S.R.L. 40-21-408-71-60CROATIA Zagreb YKK AUSTRIA GMBH BOSNIA&HERZEGOVINA REP OFFICE 385-13-872-555 YKK ROMANIA S.R.L. REPRESENTATIVE OFFICE IN SERBIA 381-21-473-9413SERBIA & MONTENEGRO Novi Sad 83
| |Country / Region Location | Company name | TEL | FAX BULGARIA Sofia YKK TURKEY SOFIA REPRESENTATIVE OFFICE 359-2-9769-433 359-2-9769-435 ITALY Milano ITALY Colonnella YKK ITALIA S.P.A. 39-02-3394-051 39-02-3533-008 SPAIN Barcelona PORTUGAL Carregado YKK SNAP FASTENER ITALIA S.P.A 39-0861-741-300 39-0861-749-548 GREECE Thessaloniki TURKEY Istanbul YKK ESPANA S.A. 34-93-447-9700 34-93-440-0003 LEBANON Beirut JORDAN Amman YKK PORTUGAL LDA. 351-263-850-150 351-263-855-082 UAE Dubai MOROCCO Casablanca YKK HELLAS A.E.B.E. 30-2310-327-830 30-2310-217-388 TUNISIA Sousse EGYPT Cairo YKK METAL VE PLASTIK URUNLERI SANAYI VE TICARET A.S. 90-212-314-79-00 90-212-314-79-03 KENIYA Mombasa SOUTH AFRICA Johannesburg YKK MIDDLE EAST SAL 961-1-586-687 961-1-586-354 SWAZILAND Mbabane MAURITIUS Rose Hill YKK MIDDLE EAST SAL JORDAN OFFICE 00962-6-582-7929 00962-6-582-7930 YKK MIDDLE EAST SAL DUBAI OFFICE 971-43-362-840 971-43-362-841 YKK MOROC S.A.R.L. 212-5-22-34-29-15 212-5-22-35-25-70 YKK TRADING TUNISIA S.A. 216-73-321-180 216-73-321-181 YKK EGYPT S.A.E. 20-2-268-7895 20-2-268-7896 YKK KENYA EPZ LTD. 254-41-432-101 254-41-435-076 YKK SOUTHERN AFRICA (PTY) LTD. 27-11-781-4240 27-11-781-4250 YKK SOUTHERN AFRICA (PTY) LTD. 268-518-6188 268-518-6130 YKK SOUTHERN AFRICA (PTY) LTD. 230-467-4431 230-466-9508 CHINA Dalian DALIAN YKK ZIPPER CO., LTD. 86-411-8762-1216 86-411-8763-2435 Beijing DALIAN YKK ZIPPER CO., LTD. BEIJING BRANCH CHINA Qingdao DALIAN YKK ZIPPER CO., LTD. QINGDAO BRANCH 86-10-5979-8626 86-10-8586-0473 CHINA Shanghai SHANGHAI YKK ZIPPER CO., LTD. CHINA Guangzhou YKK ZIPPER SHENZHEN CO., LTD. GUANGZHOU BRANCH 86-532-8163-7900 86-532-8501-6500 CHINA Shenzhen YKK ZIPPER SHENZHEN CO., LTD. FUTIAN BRANCH CHINA Xiamen YKK ZIPPER SHENZHEN CO., LTD. XIAMEN BRANCH 86-21-5403-8181 86-21-5405-0830 CHINA Kowloon YKK HONG KONG LTD. CHINA Macau YKK MACAU LTD. 86-20-3847-7968 86-20-3839-9832 HONG KONG MACAU 86-755-8287-2288 86-755-8287-2201 86-592-268-6200 86-592-268-6201 852-2378-8300 852-2375-6088 853-2848-1211 853-2848-1207 ASIA Ho Chi Minh YKK VIETNAM CO., LTD. 84-8-3823-3793 84-8-3823-3795 Bangkok YKK THAILAND CO., LTD. 66-2-718-0590 66-2-718-0591 VIETNAM Manila YKK PHILIPPINES, INC. 63-2-807-8875 63-2-807-8660 THAILAND Johor Bahru YKK MALAYSIA SDN. BHD. 60-7-237-4389 60-7-237-4890 PHILIPPINES Jakarta P.T. YKK ZIPPER INDONESIA 62-21-3193-1708 62-21-310-6751 MALAYSIA Karachi YKK PAKISTAN PTE.LTD. 92-21-5631574-7 92-21-5631578 INDONESIA New Delhi YKK INDIA PRIVATE LTD. 91-12-4392-4800 91-12-4392-4899 PAKISTAN Dhaka YKK BANGLADESH PTE. LTD. 880-2-882-2227 880-2-882-3716 INDIA Phnom Penh YKK VIETNAM CO., LTD. PHNOM PENH BRANCH 855-23-723-637 855-23-430-685 BANGLADESH Colombo YKK LANKA PRIVATE LTD. 94-11-5579200 94-112-574-614 CAMBODIA Seoul YKK KOREA CO., LTD. 82-02-3705-7900 82-02-3705-7991 SRI LANKA Taipei YKK TAIWAN CO., LTD. 886-2-2511-5157 886-2-2563-5572 KOREA Suva YKK OCEANIA LTD. FIJI BRANCH 679-385-699 679-384-909 TAIWAN Auckland YKK OCEANIA LTD. 64-9-267-0400 64-9-267-0403 FIJI NEW ZEALAND \"®\" & \"TM\" is remarks in this catalogue are trademarks of YKK CORPORATION. 1, Kanda Izumi-cho, Chiyoda-ku, Tokyo 101-8642, Japan Phone: (03) 3864-2091 Facsimile: (03) 3864-209284
©2016. YKK Corporation Printed in Japan May. 2016 CL T
Search
