MANPOWER COST
EQUIPMENT COST
7 STRUCTURAL DESIGN AND ANALYSIS The following diagrams were the results of structural analysis generated through STAAD.Pro software application. Note: The results were scaled to make it visible in the structure. Figure 1. Axial Forces Diagram Figure 2. Shear Y Diagram
Figure 3. Shear Z Diagram Figure 4. Torsion Diagram
Figure 5. Bending Moment Z Diagram Figure 6. Bending Moment Y Diagram
Figure 7. Beam Stresses Diagram Figure 8. Deflection Diagram To view the entire results generated from STAAD.Pro clearly, you may click the link attached below. https://drive.google.com/drive/folders/15THOqJH1y8Wn_iH4PfIFP8EQm2XabyMR?usp=sharing
8 CONSTRUCTION SAFETY AND HEALTH PROGRAM I. Statement of Policy – Health and Safety Program The major objective of this section is to explain to all parties involved in the planned project's construction process the methods that will be used for project safety, health, and welfare management. This policy acknowledges our responsibility to comply with the Reinforcing Occupational Safety and Health Standards (OSH Law) in Philippine Workplaces through RA 11058. It includes and expands on the health and safety information provided to parties involved in this project in order to make arrangements that will prevent accidents and promote a safe and healthy working environment. This Health and Safety Plan does not exclude any contractor from any contract responsibilities or the requirements of the OSH Law. Any apparent issues should be brought to light as soon as possible so that they can be properly addressed. II. Principles and Objectives Republic Act No. 11058, or \"An Act Strengthening Compliance with Occupational Safety and Health (OSH) Standards and Providing Penalties for Violations Thereof,\" promotes and protects worker health and safety in the Philippines. This construction project will comply with the requirements of the said act. Objectives ▪ For prevention of accidents during the construction project proper ▪ To raise the safety awareness of the project personnel ▪ Safe working standards established throughout the project ▪ To actively encourage project personnel to contribute in enhancing the project's health and safety standards
Principles ▪ Access-Egress to Site and Traffic Management The company will take appropriate measures to prevent unauthorized access and guarantee safe passage of pedestrians and vehicles past the site's access point. Expect minimum disruption. Vehicles will be parked on-site, ensuring that traffic does not generate excessive congestion or potential traffic concerns along the project location. The delivery of materials to the site will be timed differently so that there will be no disruption to main traffic in the area. In the event that unusual loads are brought to the site, the company shall guarantee that a banksman is present on the main road to direct cars. Appropriate warning signs will be put at 25m and 50m intervals on each side of all accesses to the site entrance to inform the public and motorists of construction activity. ▪ Equipment Certification Every equipment brought into the site should be certified, and all workers must have the necessary training and certification for each machine. ▪ Movement of Material When moving materials into or around the site, extreme caution must be exercised. Delivery and movement in public spaces will be given special attention. No reversing maneuvers shall be performed in public without the assistance of a spotter. • Noise, Dust, and Vibrations The company will make every attempt to maintain noise, dust, and vibrations to a minimum. Any concerns will be investigated thoroughly.
Typical noise levels will be monitored during critical periods at sensitive sites to make sure that excessive levels above the daily threshold value are handled immediately. Suitable countermeasures, such as restricting the usage of noisy equipment, will be implemented in the event of excessive noise and complaints. When materials likely to induce vibration are in use, vibration monitoring will be carried out at the nearest sensitive receptors during the construction process. Test monitoring will be carried out with the equipment turned on at low levels before gradually increasing to operational levels. Work will be halted and mitigating measures will be adopted during the construction process if monitoring reveals vibration levels connected with the facility's construction phase exceed the appropriate advisory values. The places on site where vehicles will move will normally be hard-surfaced or compressed ground, decreasing the possibility for dust emissions from the vehicles. The project compound will have hard standing areas to reduce dust generation from wind-blown debris. To reduce the possibility of wind-generated emissions from material storage bays, these bays will be placed away from the primary wind direction to reduce the effects of wind on dust. ▪ Site Rules There shall be no debris, plants, tools, etc. left in areas where members of the public could slip or hurt themselves in any way. At the end of a working day, the work site will be secured. To guarantee the safety of members of the public, any plant and equipment approaching the site or working on or near public areas must be guided by a banksman. Exclusion zones must be constructed if necessary. Before and after each shift, the exclusion zone and signage will be inspected.
To prevent the accumulation of waste and building materials, a strict housekeeping policy will be implemented. A policy of 'Clean as you Go' will be implemented and maintained. Any visitors accessing the site must check in with the site manager. Visitors will be escorted by an employee while on the site. Visitors must be made aware of and follow the site's safety guidelines and emergency procedures, such as wearing personal protective equipment. • Site Safety Controls and Measures Other than personnel officially working in the job, there will be no unauthorized access to the work area. All work areas must be kept off-limits to the general public, with appropriate NO ENTRY signage placed. This will be accomplished through fencing and the establishment of exclusion zones as needed to avoid contact with general public and local communities. • Waste Management Non-hazardous material will be sorted on site. Hazardous materials shall be segregated and stored in proper containers on-site. Hazardous waste products exiting the site will be transferred by appropriately approved contractors to legally registered, authorized, or regulated facilities. Waste bins, containers, skip bins, and storage locations will be clearly labeled with the waste categories that they should contain, including images as needed.
III. Safety and Health Standards Project Standards The minimum safety and health standards for this project will be to meet fully with the “An Act Strengthening Compliance with Occupational Safety and Health (OSH) Standards and Providing Penalties for Violations Thereof” through RA 11058, and other relevant permitted regulations and modifications hereto. If a scenario arises that may have an impact on project activity, instructions will be sent demanding adherence to particular linked regulations. If time allows, early notice of site meetings will be provided; otherwise, direction will be provided to the various contractor's site management as needed. Communications Safety & Health Risks The primary means of communication for Health and Safety matters, as well as environmental management, will be contractor induction, safety briefings, method statements, and site meetings. Selection Procedures Regular reviews for project contractors will be carried out in order to ensure proper understanding regarding health and safety. Contractors. Proper maintenance of insurance along with Safety Statement with Method Statements in specific circumstances establishing safeguards for safety and health. Each statement must be approved by personnel of the relevant contractor.
Machinery. All kinds of machinery must pass quality certification and ensure property inspection and maintenance before use. Only skilled personnel will be able to operate it solely for the intended purpose. Suppliers. Suppliers must provide appropriate Health and Safety information on their materials for inclusion in the safety file. IV. Communications and Cooperation Proper communication in order to ensure health and safety among workers Potential risk among certain categories: ▪ Laborers and skilled workers ▪ Project team members ▪ Other workforces involved ▪ Site visitors ▪ Representatives ▪ The public or civilians Fences throughout the site’s perimeter will be installed to reduce potential risks that will require temporary work certification. Along the perimeter of the constructed fence, directional and warning signs will be outfitted. Through this Safety and Health Plan, inductions, and site meetings, project team members will be made aware of potential Safety and Health concerns. Site personnel will be informed of their different corporate Safety Statements and, if appropriate, will be made aware of any specific hazards to which they may be exposed through on-site briefings. When construction on this project starts, all on-site staff will be inducted. Furthermore, site visitors will be informed of any hazards they may encounter before being permitted to enter the site.
Ongoing safety briefings and site meetings will be held to keep site personnel up to date on changing occurrences. The site office will have a copy of this Health and Safety Plan. Contract Arrangement Needed Contractor Requirements ▪ Proper training certification ▪ Evidence of safe pass ▪ Relent insurances ▪ Company safety statement ▪ Method statements Minimum Safety Requirements ▪ All sub-contractors must completely comply with RA 11058 also known as “An Act Strengthening Compliance with Occupational Safety and Health (OSH) Standards and Providing Penalties for Violations Thereof”, as well as all other applicable regulations. ▪ All Sub-contractors will be made aware of the Construction Stage, Health and Safety Plan before and after commencement meetings ▪ The provisions of this agreement must be followed by all sub-contractors. ▪ All workers, managers, directors, supervisors, and visitors must wear appropriate PPE. Sub-contractor supervision must guarantee that such a requirement is observed and implemented.
▪ All sub-contractors must guarantee that their staff are properly trained for the tasks allocated to them. ▪ Site Safety Induction will be given to all staff on-site. At the completion of the induction course, each individual who attended must sign the attendance sheet. ▪ Safety briefings must be conducted on a regular basis by all contractors. Records must be returned to the Site Manager or Safety Officer. Training. All site staff will have an initial induction talk and then engage in safety briefings, which will be conducted on a regular basis by project manager or the sub-contractor and will cover specific elements of the building process. All staff will undergo site-specific inductions and sign the relevant forms to indicate attendance at these sessions. Insurances. Prior to beginning of work on site, the sub-contractor's insurance coverage, including Employer's Liability, Public Liability, and All Risk, must be reviewed. As each sub-contractor is appointed, their insurance information is entered into a central database. The expiry date of the Subcontractors insurance shall be entered on the subcontractor register, and any subcontractor whose insurance details have not been confirmed or have expired must be removed off site. Safety Statements. Every subcontractor, employer, and self-employed individual working on this project is required to have a safety statement. The Safety Statement may need to be revised over the course of the contract work due to any new hazards/risks that may occur.
V. Arrangements for High-risk Activities Task-specific method statements will be developed that will include resources required in addition to detailing the order and execution of the activity under discussion. It will highlight the dangers as perceived by the proposer; the risks associated with the specific hazard, and the necessary control measures if the hazard cannot be avoided. It will describe who may be injured, the consequences on, and the cooperation or attendance necessary from other contractors, and will be prepared first by those seeking to carry out the activity under consideration. The project management will evaluate or have the task specific method implemented. Before the activity begins, the statement is reviewed and, if required, updated. VI. Activities with Particular Risk to Health and Safety Risk Definition and Matrix ACTIVITY OR RISKS CONTROL MEASURES HAZARD Manual Handling • Arm, back, and leg • Manual load handling will be used muscle strains and only when mechanical equipment sprains cannot be utilized. Employees who are physically incapable of • Injuries caused by performing the task will not be falling load required or permitted to do so. • Where mechanical equipment cannot be used, all personnel will get the necessary manual handling training.
Cement, Cement • Irritation on skin • The staff must evaluate loads before Dust, or Plaster engaging in manual handling to • Skin disease reduce the risk of damage as much as possible. • Respiratory problems • Wearing appropriate respiratory protective equipment will help you avoid inhaling in dust as well as dust formed by the surface treatment of hardened concrete, which may include high silica content. • Avoid skin contact by wearing long- sleeved garments and full-length pants, as well as rubber boots and gloves when needed. • If any cement gets into your eyes, quickly rinse them with warm water. • Wash off any dust or freshly mixed cement that comes on your skin right away.
Excavations • Falling material • Prior to the start of construction, the location of electric cables, sewers, Plant and • Build-up of water gas and water mains, and so on will Equipment be determined and marked. Local • Collapse governments and, if necessary, scanners will be utilized to • Overturning determine service areas. vehicles • Excavations of 1.25 meters or more • Unprotected in depth will always be correctly edges sloped or shored, pending a site- based risk assessment. Prior to entering, trench designs must be approved by a skilled person. During the hours of darkness or low visibility, warning lighting must be utilized. • The surrounding spaces must be kept orderly and tidy while excavation work is being done. • Falling from • An authorized plant contractor will vehicle ensure that all transport trucks are in good condition and equipped with • Noise the necessary safety equipment and guards when they arrive on site. Any • Interference with vehicle or equipment that is faulty public traffic will be separated. The machine will not be used until the issue has been • Stuck while on corrected and the equipment has transport been re-inspected or approved. • The plant can only be operated by authorized personnel. The
Electricity • Electrocution personnel authorized to operate the • Burns plant should have received training from the equipment supplier and/or appropriate contractor. • The plant will be parked in a secure area to avoid contact with the client's personnel and members of the general public. • Exclusion zones must be established to provide separation from moving parts and moving plants. • The company will guarantee pedestrian and vehicular traffic separation at the site location • High visibility attire is required for all site staff. • Service lines are noted on drawings. • Cooperation with utility service providers. • Always presume that overhead electrical wires are live unless verified that they have been switched out. • Use a spotter to check that there is enough space between any elevated work activity and electrical
wires. Smaller excavators with safe reach capabilities should be used. Working at Height • Falling materials • On request, the supervisor will and debris provide for any appropriate signs to notify those working above. • Person falling in the workplace • When necessary, appropriate safety equipment, such as safety belts, • Contacts with harnesses, and fall arrest devices, overhead beams, will be employed. etc. • All working places at heights will be protected to avoid falls of people and materials, such as scaffolding, railings, or a combination of the two. • Prior to working at a height, employees must report any defects in their equipment to the Supervisor. • Scaffold towers, ladders, steps, walkways, and other means of providing safe access to any work must be provided. Working platforms must be completely boarded up, complete with guardrails and toe boards. • Roofing contractors must provide a Method Statement for their projects.
Abrasive Wheels • Injuries from flying • Only trained personnel are Public Access debris permitted to operate wheel and disk mounted equipment. • Bursting of wheels or disks • Check that the disc or wheel is properly installed. • Clothing caught in wheels or disks • Protective equipment must be worn when operating abrasive wheels to • Cuts avoid risks and accidents. • Dust • All machines, particularly electrically • Noise operated machines and • Electric shock accompanying power lines, should • Fire and potential be inspected on a regular basis to explosion ensure they are in excellent working order. • Sparks from loose particles can start fires or explode when they come into contact with flammable things. Ensure that the work area is free of such materials as well as anyone who may be affected by such sparks. • Theft • All access points must be closed/barricaded to prevent • Injuries unauthorized individuals from entering. • Fatality • Posting of warning signs to • Slips, trips, fall – emphasize the dangers involved. over goods, materials, and rough terrain, into
excavations, • Only authorized personnel are manholes, sewers permitted on the premises; signs will or from heights be posted. • At the end of each shift or during breaks, all fences must be closed and locked to the site. • Loose equipment is to be removed outside of working hours. Fire • Injuries • A proper evacuation procedure • Burns must be in place and frequently monitored. • Fume inhalation • The location of the assembly will be • Explosions determined. • Damage to • Certain signage are to be placed to property avoid fire hazard • Fire drills are to be conducted and documented. • Fire extinguishers must always be available near potential sources of fire. • All workers must be trained in the selection and use of fire extinguishers. • Fire points must be clearly defined, maintained, and kept clear.
• Emergency lighting should be installed in critical areas such as stairwells and hallways, and it should be inspected twice a year. • The fire tender route must always be kept clear. Personal Protective • Employees either • All employees are legally required to Equipment and not supplied nor utilize and maintain the PPE issued Clothing (PPE) wearing PPEs to them such as proper footwear, gloves, safety goggles, hard hat, Loading/Unloading • PPEs not being face protection, and high visibility Operations used properly vest. • Injuries • Masks are issued when working in dusty conditions. Also, ear muffs are used when using loud equipment • PPE will be monitored on a regular basis. • Other protective clothing/equipment must be provided and used as needed. • Major injuries such • Vehicles are loaded and unloaded in as fractured limbs, a specific, clearly marked flat area, crush injuries, and and access is restricted. even death are possible. • Lifting equipment used for loading and unloading should be certified, and the operator is trained.
• To prevent movement during loading and unloading, vehicles are braked, chocked, and/or stabilized. • Loads are evenly distributed and secured, and trucks are not overloaded. • Loading and unloading on roadsides is done safely, with proper safety measures made for pedestrians and road traffic movement. Emergency Procedures Emergency measures for identified risks should be included in site-specific method statements. The emergency plan - which will be updated and modified as the project advances - will be used in the case of an emergency. Any contractor performing hot work must keep a suitable fire extinguisher and fire blanket nearby at all times, as well as the necessary permit to work, if applicable. Accidents, Dangerous Occurrences & Near Misses Following the incident, the site foreman will interrogate all staff involved, as well as all witnesses, and fill in the following information: • Location of accident • Date and time of accident • Description of accident • Personal details of people injured and involved • Injuries and damages caused • Cause of accident • Name of witnesses • Area condition • Images of the location
VII. General Safety Arrangements for On-Site Consultation on Safety and Health In general, matters concerning health and safety shall be communicated to people on site after being emphasized at site meetings or otherwise by site management at inductions or safety briefings. Health and Safety Monitoring Arrangements Monitoring will be arranged in the form of scheduled checks or audits, compliance with Statutory Requirements, site rules and procedures as set out or referred to in these documents or elsewhere in the documentation package from time to time. Any corrective action deemed essential must be taken as quickly as reasonably possible, depending on the urgency / priority of the situation. Site Rules and Notification Procedures If the necessity arises to make site regulations, such rules must be made in collaboration with Senior Site Management, who will immediately notify their workers of such an event. Safety Briefings If necessary, Sub-contractors Foremen will be given safety briefing topics at Site Safety Meetings. The first topic that Subcontractors should discuss with their employees is their safety method statement for the job that will be done on site. Further safety briefing presentations must be relevant and specific to the sort of work performed on site by the Subcontractor. VIII. Emergency Plan Certain measures will be carried out to avoid environmental incidents, however if these incidents occur then the following procedure must be carried out.
Accident and Emergency Procedures • Raise the alarm immediately • Inform authorities and contact emergency services • Evacuate in an orderly manner and try to minimize chaos • If safety measures have been set, you may deal with the situation The acting supervisor must conduct a headcount to establish if anyone is missing from the group and immediately report the current personnel status to management. The supervisor must make it clear that no one is permitted to leave the premises until the accident or emergency has been completely resolved. The Site Management must assign someone to answer the phone and direct emergency services to the site, as well as receive and brief the emergency services. Emergency services must have access to a safe office. All operatives must be counted and the situation at the assembly point must be checked. In the event of an emergency, emergency hotlines must be dialed immediately and in a calm manner, state the following: • Name of the company: ND Construction • Site: Barangay San Vicente, Alaminos, Laguna • Site Telephone No: Give your telephone number Organize a First Aider to provide first aid to the injured party if it is safe to do so, and notify the Safety Manager by calling the Head Office.
Emergency Hotlines LOCATION NUMBER DESCRIPTION Quezon City 02-8911-5061 Quezon City 02-82840-800 NDRRMC Alaminos, Laguna 049-561-0311 PAGASA Alaminos, Laguna 049-521-0153 MDRRMO Alaminos, Laguna 049-521-0166 BFP Alaminos, Laguna 049-567-1531 PNP San Pablo, Laguna 049-562-0728 St. Clement Medical Clinic SPC Medical Center
9 CONTRACTS AND SPECIFICATIONS CONTRACT AGREEMENT AND TERMS THE PROJECT STAKEHOLDER OF THE 2-STOREY RESIDENTIAL BUILDING AT BARANGAY SAN VICENTE, ALAMINOS, LAGUNA, PHILIPPINES, MR. JUAN V. DELA CRUZ, hereby contracts with “ND Construction,” a construction firm, for profit with an address of One Million Nine Hundred Forty One Thousands Four Hundred Eighty-Four and point Zero One pesos (₱ 1,941,484.01), to perform all work in connection with design and build, as ,said work is set forth in the Plans and Specifications furnished by the Design-Build Firm and other Contract Documents hereafter specified. ARTICLE I - CONTRACT DOCUMENTS Contract documents include written documents that incorporate the roles, responsibilities, and work under the construction contract which are legally-bonded between the two parties – owner and contractor. Listed below are the inclusions of the contract documents: ▪ Scope of Work ▪ Time of Completion ▪ Contract Sum ▪ Guarantee ▪ Performance and Payment Bonds ▪ Safeguards and Warrants ▪ Modification ▪ Successors and Assigns ▪ Governing Law ▪ No Waiver ▪ Entire Agreement ▪ Venue of Court Action
The contract and its requirements for the party are one of the following documents that are needed for the binding process. The purpose of the documents is to include all materials, equipment, and labor. Additionally, the terms and conditions along with the materials required for the execution of the work are essential. Thus, the works can be reasonably inferred from the Contract Documents to be required as to achieve the intended results. Both parties must either sign two copies of the contract documents. Otherwise, the owner’s representative (OR) must be held responsible in identifying the attachments relevant from the contract documents. This certifies that the contractor inspected the worksite and acquainted with the local circumstances by signing the contract. If conflicts occur between agreements and terms of both parties, the regulations of the contract should be applied. Furthermore, if the request for proposal is not aligned with the contractor’s proposal, the former must adapt to the changes as their work is aimed to specify the project's scope. ARTICLE II - SCOPE OF WORK In most cases, the Design-Build Firm will be responsible for providing all of the necessary planning, design, and architectural/engineering services required for the building of the Project, in addition to any other services that are required for its proper design. THAT the CONTRACTOR shall, in compliance with the conditions of and subject to the provisions enclosed in the transcripts provided for in Article I thereto with a mandate that this construction project conforms to ND Construction, and in deliberation of the lump
sum payment hereinafter mentioned shall immediately and accountably perform all labor, procure the necessary equipment and materials, and utilize workforce and operations required to complete the Construction of the Two-Storey Residential Building for Mr. Juan V. Dela Cruz located at Barangay San Vicente, Alaminos, Laguna, as per plan and specifications of the owner. The work comprises of the individual work elements listed below: ACTIVITY DESCRIPTION START END DURATION General Requirements Supervision 6-Jun-22 27-Oct-22 127 days 6-Jun-22 27-Oct-22 127 days Occupational Health and Safety 6-Jun-22 27-Oct-22 127 days Mobilization/Demobilization Earth Works 6-Jun-22 13-Jun-22 8 days A. Site Clearing and Excavation 13-Jun-22 13-Jun-22 1 day B. Disposal 13-Jun-22 13-Jun-22 C. Gravel Bedding 3 days Foundation Works 13-Jun-22 15-Jun-22 D. Rebar Fabrication and Installation (Up to Ground Level) 15-Jun-22 15-Jun-22 1 day E. Footings and Foundation 15-Jun-22 15-Jun-22 8 days 15-Jun-22 22-Jun-22 1 day Fabrication and Installation of Footing Formworks 23-Jun-22 23-Jun-22 1 day 8 days Concrete Pouring 23-Jun-22 23-Jun-22 1 day 23-Jun-22 23-Jun-22 Curing 24-Jun-22 1-Jul-22 3 days Removal of Footing Formworks 2-Jul-22 2-Jul-22 F. Column 2-Jul-22 2-Jul-22 Fabrication and Installation of Column Formworks Concrete Pouring 2-Jul-22 4-Jul-22 Curing Removal of Column Formworks G. Back Filling and Compaction H. Tie Beam Rebar Fabrication and Installation
Fabrication and Installation of Column Formworks 4-Jul-22 4-Jul-22 1 day Concrete Pouring Curing 4-Jul-22 4-Jul-22 8 days Removal of Footing Formworks 4-Jul-22 11-Jul-22 1 day I. Septic Tank, Manhole, and Drainage Installation 12-Jul-22 12-Jul-22 3 days Structural Works (1st Floor) J. Column Works 13-Jul-22 15-Jul-22 2 days Formwork and Rebar Fabrication and Installation 1 day Concrete Pouring 15-Jul-22 16-Jul-22 8 days Curing 17-Jul-22 17-Jul-22 1 day Removal of Column Formworks 17-Jul-22 24-Jul-22 K. Wall Construction 25-Jul-22 25-Jul-22 1 day Reinforcing steel bar to support CHB 2 days Stacking CHB 25-Jul-22 25-Jul-22 2 days Lintel works 25-Jul-22 27-Jul-22 L. Beam and Slab Works 27-Jul-22 28-Jul-22 2 days Formwork and Rebar Fabrication and Installation 1 day Concrete Pouring 29-Jul-22 30-Jul-22 8 days Curing 30-Jul-22 30-Jul-22 1 day Removal of Formworks 30-Jul-22 6-Aug-22 M. Stair Works 8-Aug-22 8-Aug-22 2 days Formwork and Rebar Fabrication and Installation 1 day Concrete Pouring 8-Aug-22 9-Aug-22 8 days Curing 9-Aug-22 9-Aug-22 1 day Removal of Formworks 9-Aug-22 16-Aug-22 Structural Works (2nd Floor) 17-Aug-22 17-Aug-22 2 days N. Column Works 1 day Formwork and Rebar Fabrication and Installation 17-Aug-22 18-Aug-22 8 days Concrete Pouring 19-Aug-22 19-Aug-22 1 day Curing 19-Aug-22 26-Aug-22 Removal of Column Formworks 27-Aug-22 27-Aug-22 1 day O. Wall Construction Reinforcing steel bar to support CHB 29-Aug-22 29-Aug-22
Stacking CHB 29-Aug-22 1-Sep-22 3 days Lintel works 1-Sep-22 2-Sep-22 2 days P. Beam Works Formwork and Rebar Fabrication and Installation 3-Sep-22 5-Sep-22 2 days Concrete Pouring 5-Sep-22 5-Sep-22 1 day Curing 5-Sep-22 12-Sep-22 8 days Removal of Beam Formworks 13-Sep-22 13-Sep-22 1 day Finishing Works Q. Roofing Works 13-Sep-22 13-Sep-22 1 day Installation of Roof Trusses 14-Sep-22 14-Sep-22 1 day Installation of Roof Sheets including ridge roll 15-Sep-22 15-Sep-22 1 day Installation of Roof Gutter and Flashing R. Slab Works (Ground Floor) 16-Sep-22 16-Sep-22 1 day Rebar Fabrication and Installation 17-Sep-22 17-Sep-22 1 day Concrete Pouring 17-Sep-22 24-Sep-22 8 days Curing S. Ceiling Works 26-Sep-22 26-Sep-22 1 day Building ceiling joist 28-Sep-22 28-Sep-22 1 day Installing plywood ceiling cover 29-Sep-22 29-Sep-22 1 day Adding cornices T. Architectural Works 30-Sep-22 02-Oct-22 4 days Installation of Doors 30-Sep-22 3-Oct-22 5 days Installation of Window 5-Oct-22 6-Oct-22 2 days Installation of Balcony Railing U. Plumbing Works 7-Oct-22 7-Oct-22 1 day Septic Tank 7-Oct-22 7-Oct-22 Catch Basin 8-Oct-22 8-Oct-22 1 day Waterline 8-Oct-22 8-Oct-22 Sanitary Line 9-Oct-22 9-Oct-22 1 day Storm Drainage Line V. Electrical Works 10-Oct-22 10-Oct-22 1 day Electrical Fixture
Light Fixture 12-Oct-22 12-Oct-22 1 day 13-Oct-22 13-Oct-22 1 day Panel Board 14-Oct-22 17-Oct-22 4 days W. Plastering Works 19-Oct-22 20-Oct-22 2 days Plastering of Interior and Exterior Walls 21-Oct-22 23-Oct-22 3 days X. Tile Works 24-Oct-22 27-Oct-22 3 days Y. Painting Works Applying primer coating to wall Final paint coating ARTICLE III - TIME OF COMPLETION The activities to be undertaken by the CONTRACTOR here under the contact agreement must begin ten (10) calendar days after the CONTRACTOR receives and accepts client's Notice to Proceed. The construction of Mr. Juan V. Dela Cruz's two- story residential building must be finished throughout one hundred twenty-seven (127) calendar days, including Saturdays. If the CONTRACTOR refuses to perform the work or fails to comply for some other reason, the CONTRACTOR agrees to pay the client 0.1% of the cumulative contract amount each day of delay until the project is completed and validated by the client, or until the client assumes the management of the project or transfers it to another contractor until the client can justifiably safeguard the project completion. This amount shall be removed from any payment due or which may become due to the contractor under the contract, and/or insurance claims shall be collected from the contractor's performance bond or the contractor's bailee, whomever is most convenient for the OWNER, Mr. Juan V. Dela Cruz. ARTICLE IV - THE CONTRACT SUM The OWNER chose to pay the CONTRACTOR in Philippine Monetary System the sum of ONE MILLION NINE HUNDRED FOURTY ONE THOUSAND FOUR HUNDRED EIGHTY-FOUR AND POINT ZERO ONE PHILIPPINE PESO (₱ 1,941,484.01) for faithful and satisfactory performance of the contract in compliance with all contract papers and subject to the deductions herein provided.
a. The monthly premium will depend on satisfactory completion of the work as documented by the CONTRACTOR, approved by the Design Consultant, and accompanied by a certification from the OWNER. The application for transactions, authentication of payouts, etc. shall be in compliance with the provision and conditions set forth in the General Conditions affixed thereof or incorporated herein. The entirety of the payment will be made available upon completion of the project and acquiescence by the Contractor of a notarized certification that all taxes owed to him and all liabilities for commodities used and labor engaged in line with this contract have been paid in full. b. Ten percent (10%) of progress payments are subject to retention, also known as \"withholding balance.\" This balance shall be constituted on the entire value payable to the Contractor preceding to any withdrawals and will be deducted for each transaction until 50% of the work, as decided by the OWNER, has been completed. If after 50% of the work is performed competently and on-time, no extra payment shall be imposed on the subsequent progress balance. Otherwise, 10% retention shall be imposed and at total retention money is required upon final work acceptance. After cumulative progress payments to the Contractor totaling at least 50% of the entire contract price, the OWNER may request a share of the retention money commensurate with the percentage of work accomplished, as assessed by the OWNER. The CONTRACTOR must deposit an irreversible collateral letter of credit in behalf of the OWNER to cover the 10% retention. Any discharge of retention money by the OWNER does not relinquish the OWNER's right to be compensated for damage caused by the CONTRACTOR under Art.20 of the New Civil Code. c. The CONTRACTOR shall monitor and ensure on his own expenditure in accordance to warranty coverage which as follows: (1) Project Provider’s Wide- Hazard Protection; (2) Conveyance to the Site Location of Machineries and Equipment, and Materials Possessed by the Provider; (3) Detailed liability coverage for the death or bodily injury of employees of the Contractor; and (4)
Wide array coverage of insurance for third party liability to the Contractor's direct or indirect conduct or abrogation which results to damages to multiple parties. d. That the CONTRACTOR shall be liable for collecting the insurance premium. ARTICLE V – GUARANTEE The CONTRACTOR fully ensures the services listed in this contract and all the materials and supplies that will be utilized in the project development, as well as the craftsmanship of all its work under this contract and agrees to pay for its own account and/or its own expenditures. The CONTRACTOR shall assume full responsibility for any damage or destruction of the works only after the OWNER has given its final confirmation to the project, excluding those caused by unforeseen circumstances. Wherein in Section 62.2.3.3 of IRRA of R.A. 9184, CONTRACTOR will be required to impose a collateral warranty denominated in Philippines Pesos and shall remain lawful for one (1) year, the day the owner received the certificate of final acceptances and shall only be returned if any lapses occur within the given time period. Furthermore, the provisions of An. 1723 of the New Civil Code shall also enforce to assure the CONTRACTOR's affirmation of quality deliverance ARTICLE VI - PERFORMANCE AND PAYMENT BONDS In full compliance with the contract's Instruction to Bidders and General Conditions, the contractor shall furnish and file with the owner. Upon acceptance, a Performance Bond in accordance with Section 39 of the Revised Implementing Rules and Regulations of RA 9184 to guarantee the full and faithful efficiency of the agreement and to answer for any liability suffered by the owner as a result of the contractor's violation of labor and other laws. However, in the case of expiration or termination of this contract for violation, the bond shall be automatically forfeited in favor of the owner and become immediately
payable and collected by the owner. Otherwise, the bond shall stay and continue in full effect until the stated duties as to the completion and faithful compliance with the contract, liquidated damages, and cost of materials and labor is fulfilled. ARTICLE VII - SAFEGUARDS AND WARRANTS The contractor shall provide and do everything required to fulfill its responsibilities. Under this contract in accordance with the true intent and meaning of the other contract documents taken together (drawings, plans, and specifications), provided that the same shall be inferred therefrom, and should the contractor find any discrepancy in the drawings, plans, and specifications, the contractor shall promptly refer the same to the owner resident supervisor or inspector. The owner claims the right to add or enhance the number of laborers or workers allocated to the construction site if the owner believes that the exigencies of the situation warrant it. The contractor considered an independent contractor, and as such, he takes all obligations and liabilities resulting from the Employee's Liability Act, as well as any other existing and subsequent laws that may influence the rights of employees or laborers hired in the fulfillment of this contract. If the owner is liable for any of the contractor's violations of labor regulations, the contractor must compensate the owner for any money the latter is obliged to pay to these laborers, and the Performance Bond is responsible for this contingency. Regardless of any conditions of this contract, the owner has the right and/or power to terminate the contract without the need for judicial action by providing written notice to the contractor if he fails to comply with any of its requirements. The contract hereby declares that it has not provided or pledged to pay money or gifts to any official of the owner and/or any other office, or agency, in order to guarantee this conflict, and any violation of this assurance shall be sufficient basis for the owner to withdraw or terminate the contract.
The contractor is required to develop the construction safety and health program as specified in the proposal, which includes, among other things, mandating its employees to have Identification Cards, which should be available online when inspected by university security personnel or any authorized representative of the owner. ARTICLE VIII – MODIFICATION No modification or alteration to the agreement will be effective or binding on the parties unless done in writing and signed by parties involved meant to be obligated by it. ARTICLE IX - SUCCESSORS AND ASSIGNS No modification or amendment to this Agreement shall be effective or enforceable unless it is in notarized by the party or parties to whom it applies ARTICLE X - GOVERNING LAW Subject to other conditions herein, the Agreement binds and benefits the parties' heirs and assigns. ARTICLE XI - NO WAIVER The Agreement shall be read and performed in accordance with the laws of the Philippines, and the Parties agree that venue for matters pertaining to the subject matter of this Agreement shall be in Alaminos, Laguna. ARTICLE XII - ENTIRE AGREEMENT The County's failure to enforce any one or any of the provisions of the CONTRACT at any time or for any period of the time shall not be regarded as or constitute a waiver of any such provision or provisions or of its right afterwards to dispute each and every such condition.
ARTICLE XIII - VENUE OF COURT ACTION Should the OWNER or CONTRACTOR file a judicial action originating from this contract, the parties mutually agree that the venue shall be a related court in the province of Laguna. IN WITNESS WHEREOF, the parties hereto have placed their confirmation on this agreement this 5th day of May 2022 in ALAMINOS, LAGUNA, PHILIPPINES. MR. JUAN V. DELA CRUZ ND CONSTRUCTION Alaminos, Laguna Santa Cruz, Laguna By: ENGR. JUDE MARY VERONE M. OROSA MR. JUAN V. DELA CRUZ Proprietor Alaminos, Laguna Santa Cruz, Laguna (OWNER) (CONTRACTOR) Signed in the presence of: 1.MARK JEROME VILLANUEVA 2. RYCESA P. ANGELES 3.MARGIE L. PANALIGAN 4. ALYZZA MARIELLA N. AQUINO 5. PRINCE LUKE B. MAGBOO 6. JERICO R. ROSALES 7. JEGO GABRIEL S. VALENCIA 8.HARRELSON Q. PISANO 9. KEN VRIANE A. CUA
BEFORE ME, this 3rd day of June, 2022 at ALAMINOS, LAGUNA personally appeared: Name Comm. Tax Cert Date/Place Issued Mr. Juan V. Dela Cruz __1_2_3_4_5_6_7_89____ 05_/_0_5_/2_0_2_2_,_A_l_a_m_i_n_o_s,_L_a_g_u_na Engr. Jude Mary Verone M. Orosa __9_8_7_6_5_4_3_2_1___ 05_/_0_5_/2_0_2_2_,_S_ta_._C__ru_z_,_L_a_g_u_na known to me to be the same persons who executed the foregoing instrument and they acknowledged to me that the same is their voluntary act and deed. This instrument consisting of twelve (12) pages including this acknowledgement has been signed on each page by parties and their witnesses and sealed with my notarial seal. WITNESS MY HAND AND SEAL on the date and place first above given.
10 CONSTRUCTION PROJECT SCHEDULE A project schedule is a timetable that shows the start and end date of all project tasks, how the tasks relate to each other and usually which team members or other resources are responsible for delivery.
GANTT CHART GANTT CHART
To view the entire Gantt chart clearly, you may click the link attached below and open the file using Microsoft excel. https://docs.google.com/spreadsheets/d/1_cSJhnk2X_NTtOKUF8VoQjjV5Ig46PpK/edit?usp=sharing&ouid= 107508758264219660552&rtpof=true&sd=true
PRECEDENCE DIAGRAM To view the entire Precedence Diagram clearly, you may click the link attached below and open the file using Microsoft excel. https://docs.google.com/spreadsheets/d/1_cSJhnk2X_NTtOKUF8VoQjjV5Ig46PpK/edit?usp=sharing&oui d=107508758264219660552&rtpof=true&sd=true
EQUIPMENT SCHEDULE
To view the entire Equipment Schedule clearly, you may click the link attached below and open the file using Microsoft excel. https://docs.google.com/spreadsheets/d/1_cSJhnk2X_NTtOKUF8VoQjjV5Ig46PpK/edit?usp=sharing&oui d=107508758264219660552&rtpof=true&sd=true
Search
