POWER FEED END RECESSED CHANNELS WITH TRIM System Model Description Finish S2 CT04-FE 4 ft Trim Recessed Feed End Required Power Feed Run BK Black 4\" CT08-FE 8 ft Trim Recessed Feed End Connected Power Unit Required WT White 2/\" CT12-FE 12 ft Trim Recessed Feed End See page 44 (sold separately) 2/\" Example: S2CT04-FE-BK Each section comes with two matching end caps and may be cut at end run. 2/\" RECESSED CHANNELS WITH TRIM System Model Description Finish CT01 1 ft Trim Recessed Channel CT1.5 1.5 ft Trim Recessed Channel S2 CT04 4 ft Trim Recessed Channel To extend channel runs after feed end BK Black CT08 8 ft Trim Recessed Channel WT White CT12 12 ft Trim Recessed Channel Example: S2CT08-BK Each section comes with two matching end caps and may be cut at end run. CHANNEL COVER Channel Cover 8ft S2C-COV08 BK Black 8ft length may be field cut, Suitable for Finish WT White top or bottom channel coverage. BK Black SUSPENSION HARDWARE CONNECTORS BK Black Accessories Accessories System System Finish Mount Clip I Connector S2CSR-I Support recessed channel S2CR-CLIP BK Black Joins two sections of with 1/4 - 20 threaded rod channel with eletrical (rod by others) continuity Cable Suspension Dead I Connector S2C-ID Support Recessed Channel S2C-C96 BK Black Joins two sections from plenum ceiling Includes of channel without 96in aircraft cable; may be eletrical continuity field cut End Cap S2CT-EC BK Black Stem Suspension Additional end cap WT White Support Recessed Channel from plenum ceiling Includes L Connector BK Black two 48in stem; may be field S2C-S96 BK Black Use to join two sections S2CT-L WT White cut S2C-LOOP BK Black 90°. Suspension Loop T Connector S2CT-T BK Black Mechanical loop Use to join three WT White Supports up to 15 lb sections. X Connector S2CT-X BK Black Use to join four track WT White sections Inside Corner S2CT-IC BK Black Joins ceiling to wall WT White sections S2CT-OC BK Black Outside Corner WT White Joins wall to wall sections waclighting.com 51
RECESSED TRIMLESS CHANNEL BUILD IT CHOOSE YOUR CHANNELS AND CONNECTORS • Power feed from feed end channel to energize your run. • Support Strut with screws into rear blocking, 1/4\"-20 tie rod (by others), or stem or aircraft cables to plenum ceiling. Minimum two supports per 4ft section. Minimum three supports per 8ft and 12ft section. • For patterns, choose L, T, X, or corners. Note: STRUT is field cut at end of run. For patterns and custom length channels, consult factory. CHOOSE YOUR ELEMENTS • Refer to element specifications to appropriately select elements. • Total the wattage of the system. CHOOSE YOUR CONNECTED POWER UNIT (CPU) • Select remote mount CPU. • Select appropriate wattage based on total system wattage. Note: recommended sizing up as feasible for increased system capability. ACCESSORIZE • Add channel covers, lenses, or glare control accessories as desired. A S2CL08-FE 8FT FEED END RECESSED TRIMLESS CHANNEL G S2CL-OC RECESSED TRIMLESS OUTSIDE CORNER B S2CL04 4FT RECESSED TRIMLESS CHANNEL H S2CR-CLIP 1/4\"-20 TIE ROD MOUNTING CLIP C S2CL08 8FT RECESSED TRIMLESS CHANNEL I S2C-C96 CABLE SUSPENSION D S2CSR-I I CONNECTOR J S2C-S96 STEM SUSPENSION E S2CL-IC RECESSED TRIMLESS INSIDE CORNER K S2CPU-R600-S-BK REMOTE CPU F S2CL-L RECESSED TRIMLESS L CONNECTOR L BY OTHERS FIELD WIRING TO CPU by WAC K L H I J A D G C D DD B E waclighting.com B D FD 52
POWER FEED END RECESSED TRIMLESS CHANNELS System Model Description Finish CL04-FE 4 ft Trimless Recessed Feed End Required Power Feed Run 4\" S2 CL08-FE 8 ft Trimless Recessed Feed End Connected Power Unit Required BK Black 4/\" CL12-FE 12 ft Trimless Recessed Feed End See page 44 (sold separately) Example: S2CL04-FE-BK Each section comes with two matching end caps and may be cut at end run. RECESSED TRIMLESS CHANNELS System Model Description Finish CL01 1 ft Trimless Recessed Channel CL1.5 1.5 ft Trimless Recessed Channel S2 CL04 4 ft Trimless Recessed Channel To extend channel runs after BK Black 2 /\" CL08 8 ft Trimless Recessed Channel feed end 4/\" CL12 12 ft Trimless Recessed Channel Example: S2CL12-BK Each section comes with two matching end caps and may be cut at end run. CHANNEL COVER Channel Cover 8ft S2C-COV08 BK Black 8ft length may be field cut, Suitable for top or bottom channel coverage. CONNECTORS System Finish SUSPENSION HARDWARE System Finish S2CSR-I BK Black Accessories Accessories S2CR-CLIP BK Black S2C-ID BK Black I Connector S2CL-EC Mount Clip S2C-C96 BK Black Joins two sections of BK Black Support recessed channel channel with eletrical BK Black with 1/4 - 20 threaded rod S2C-S96 BK Black continuity BK Black (rod by others) S2C-LOOP BK Black Dead I Cable Suspension Connector Support Recessed Channel Joins two sections of from plenum ceiling Includes channel without eletrical 96in aircraft cable; may be continuity field cut End Cap Stem Suspension Additional end cap Support Recessed Channel from plenum ceiling Includes L Connector S2CL-L two 48in stem; may be field Use to join two sections 90°. cut T Connector S2CL-T Suspension Loop Use to join three sections. Mechanical loop Supports up to 15 lb X Connector S2CL-X BK Black Use to join four track sections Inside Corner S2CL-IC BK Black Joins ceiling to wall sections Outside Corner S2CL-OC BK Black Joins wall to wall sections waclighting.com 53
SUSPENDED CHANNEL BUILD IT CHOOSE YOUR CHANNELS AND CONNECTORS • Power feed from end with S2CP-FE, the middle with S2CP-FI, or from the TRIG with S2CPS-FTRIG to energize your run. • Support Strut with cable or stem suspensions. Minimum two supports per 4ft and 8ft sections. Minimum three supports per 12ft section. • For patterns, use the TRIG connector. TRIG connector can accept as few as two and as many as six connections. Order additional TRIG connectors as needed. TRIG connectors have a switch to maintain pattern polarity. Note: STRUT is field cut at end of run. For patterns and custom length channels, consult factory. CHOOSE YOUR ELEMENTS AND/OR INDIRECT LIGHTING ELEMENTS Note: Suspended strut is compatible with indirect lighting by default. • Refer to element specifications to appropriately select elements • Total the wattage of the system CHOOSE YOUR CONNECTED POWER UNIT (CPU) • Select remote mount or surface CPU • Select appropriate wattage based on total system wattage. Note: recommended sizing up as feasible for increased system capability. ACCESSORIZE • Add channel covers, lenses, or glare control accessories as desired. A S2CPS04 4FT SUSPENDED CHANNEL F S2C-FS96 STEM FEED SUSPENSION S2C-S96 STEM SUSPENSION B S2CPS12 12FT SUSPENDED CHANNEL G S2CPS-TRIG TRIG S2CPU-R320-S-BK REMOTE CPU C S2CP-FE FEED END H BY OTHERS FIELD WIRING TO CPU D S2C-C96 CABLE SUSPENSION I E S2CP-CP CABLE CANOPY J D G D by WAC J by WAC G B B I J G E D FD A C C A H 54 waclighting.com
SUSPENDED CHANNELS System Model Length Finish CPS01 1 ft Suspended Channel CPS1.5 1.5 ft Suspended Channel Direct and/or Indirect Compatible S2 CPS04 4 ft Suspended Channel Connected Power Unit Required BK Black 2 /\" CPS08 8 ft Suspended Channel See page 44 (sold separately) WT White CPS12 12 ft Suspended Channel Example: S2CPS08-BK Each section comes with two matching end caps and may be cut at end run. CHANNEL COVER 1 /\" Channel Cover 8ft S2C-COV08 BK Black 8ft length may be field cut, Suitable for System WT White top or bottom channel coverage. S2CPS-FTRIG Finish BK Black TRIG S2CPS-TRIG WT White BK Black Accessories WT White Trig with Feed Includes 96in feed wire, and 2 channel connectors. Suspension Hardware sold separately. Aircraft cable only. Trig Includes 2 channel connectors. Suspension Hardware sold separately. Stem and Aircraft cable compatible. Adapter S2CPS-NADP BK Black Additional Trig connectors WT White See page 46 for more information about the TRIG hub connector system CONNECTORS SUSPENSION HARDWARE Accessories System Finish Accessories System Finish BK Black Feed End S2CP-FE BK Black Cable Canopy S2CP-CP WT White Includes 96in feed wire WT White Covers a standard 4in BK Black and 10 wire guides junction box. Use with NI Nickel cable feed connectors BK Black NI Nickel I Connector with Feed S2CP-FI BK Black Cable Suspension S2C-C96 BK Black Includes 96in of feed WT White Suspend channel from ceiling. S2C-SC96 WT White wire and 10 wire guides Includes 96in aircraft cable; S2C-FS96 BK Black may be field cut WT White I Connector S2CP-I BK Black BK Black Joins two sections of S2C-ID WT White Sloped Ceiling WT White channel with electrical BK Black Cable Suspension BK Black continuity WT White Suspend channel from a sloped ceiling. Includes 96in Dead I aircraft cable; may be field cut Connector Joins two sections of Stem Feed Suspension channel without Suspend channel from ceiling electrical continuity with feed. Includes two 48in stem; may be field cut Stem Suspension S2C-S96 Suspend channel from ceiling. Includes two 48in stem; may be field cut End Cap S2CPS-EC BK Black Sloped Ceiling Additional end cap WT White Stem Suspension Suspend channel from a sloped ceiling. Includes two S2C-SS96 48in stem; may be field cut S2C-LOOP Suspension Loop Mechanical loop Supports up to 15 lb waclighting.com 55
SURFACE MOUNTED CHANNEL BUILD IT CHOOSE YOUR CHANNELS AND CONNECTORS • Power feed from end with S2CS-FE or S2CS-FEB, or feed from the TRIG WITH S2CP-FTRIG to energize your run. • Support with screws into support or joist. Minimum two supports per 4ft section. Minimum three supports per 8ft and 12ft section. • For patterns, use the TRIG connector. The TRIG connector can accept as few as two and as many as six connectors. Order additional TRIG connectors as needed. TRIG connectors have a switch to maintain pattern polarity. Note: STRUT is field cut at end of run. For patterns and custom length channels, consult factory. CHOOSE YOUR ELEMENTS • Refer to element specifications to appropriately select elements. • Total the wattage of the system. CHOOSE YOUR CONNECTED POWER UNIT (CPU) • Select remote mount or surface mount (using side knock out provisions) CPU. • Select appropriate wattage based on total system wattage. Note: recommended sizing up as feasible for increased system capability. ACCESSORIZE A • Add channel covers, lenses, or glare control accessories as desired. A C C A C A C A A A A A CA A C C C C A D FA A BA by WAC C E C A S2CPS04 4FT SURFACE CHANNEL B S2CPS-FTRIG TRIG WITH FEED C S2CPS-TRIG TRIG D S2CPU-R320-S-BK REMOTE CPU E BY OTHERS FIELD WIRING TO CPU 56 waclighting.com F S2CP-CP SUSPENDED CANOPY
SURFACE CHANNELS System Model Length Finish 2 /\" BK Black 1 /\" CPS01 1 ft Surface Channel WT White CPS1.5 1.5 ft Surface Channel 57 S2 CPS04 4 ft Surface Channel Connected Power Unit Required BK Black CPS08 8 ft Surface Channel See page 44 (sold separately) WT White CPS12 12 ft Surface Channel Example: S2CPS04-BK Each section comes with two matching end caps and may be cut at end run. CHANNEL COVER S2C-COV08 Channel Cover 8ft 8ft length may be field cut, Suitable for top or bottom channel coverage. TRIG Accessories System Finish S2CPS-FTRIG BK Black Trig with Feed WT White Includes 96in feed wire, and 2 channel connectors. Trig S2CPS-TRIG BK Black Includes 2 channel connectors. WT White Adapter S2CPS-NADP BK Black Additional Trig connectors WT White See page 46 for more information about the TRIG hub connector system Finish BK Black CONNECTORS System WT White Accessories Feed End S2CS-FE Includes 24in feed wire Junction Box S2CS-FEB BK Black 3in junction box with side knock outs WT White BK Black I Connector S2CSR-I WT White Joins two sections of channel S2C-ID BK Black with electrical continuity WT White Dead I Connector Joins two sections of channel without electrical continuity End Cap S2CPS-EC BK Black Additional end cap WT White Inside Corner S2CS-IC BK Black Joins ceiling to wall sections S2CS-OC WT White BK Black Outside Corner WT White Joins wall to wall sections S2C-LOOP BK Black Suspension Loop Mechanical loop Supports up to 15 lb waclighting.com
Copyright © 2020 by WAC Lighting. All rights reserved. This catalog is copyrighted and WAC Lighting reserves the right to use any and all measures available to it under the law against anyone who copies or derives from its copyrighted work. 58 waclighting.com
Search
