RHAU-MKT Thread ID Booklet 2021-05-13 V1-7

THREAD ID KIT POCKET GUIDE & IDENTIFICATION KIT Part Number: RYCO-MKT0250 Part Number: RYCO-MKT0250D THREAD ID KIT CONTAINS:  Thread identification booklet  Vernier caliper (digital)  Metric thread gauge  Imperial thread gauge  Seat angle gauge  15 cm / 6 inch ruler The RYCO Thread ID Kit is to assist with identification of hydraulic threads and connectors. Selection of hydraulic connectors can be complex due to the large array of thread types that are commonly available. Correct identification is of vital importance, as the incorrect application of high pressure connectors presents an immediate safety risk. Using the RYCO 24•7 Thread ID Kit assists with the mitigation of these risks to productivity, environment and safety. 46

SOFT SEAL 30.0 mm 60˚ 1.3/16” UN 12 TPI 47 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL RYCO O RINGS DASH BSPP DASH UNO INTRODUCTION -02 -07 -04 PART NO -08 PART NO -06 RO-BP02 -09 RO-UN07 -08 RO-BP04 -12 RO-UN08 -10 RO-BP06 -14 RO-UN09 -12 RO-BP08 -17 RO-UN12 -16 RO-BP10 -19 RO-UN14 -20 RO-BP12 -21 RO-UN17 -24 RO-BP16 -26 RO-UN19 -32 RO-BP20 -30 RO-UN21 RO-BP24 RO-UN26 RO-BP32 RO-UN30 AIR CONDITIONING SAE FLANGE DASH PART NO DASH PART NO TAPERED THREADS -10 RO-AC10 -08 RO-SF08 -12 RO-AC12 -12 RO-SF12 -14 RO-AC14 -16 RO-SF16 -20 RO-SF20 ORFS -24 RO-SF24 -32 RO-SF32 DASH PART NO -40 RO-SF40 -09 RO-FS09 -11 RO-FS11 METRIC (DKOL) -13 RO-FS13 -16 RO-FS16 DASH PART NO METAL SEAL -19 RO-FS19 -12 RO-DL12 -23 RO-FS23 -14 RO-DL14 -27 RO-FS27 -16 RO-DL16 -32 RO-FS32 -18 RO-DL18 -22 RO-DL22 BSPP ENCAPSULATED MALE -26 RO-DL26 -30 RO-DL30 DASH PART NO -36 RO-DL36 -02 RO-WD084 -45 RO-DL45 -04 RO-WD116 -52 RO-DL52 -06 RO-WD147 -08 RO-WD185 METRIC (DKOS) SOFT SEAL -12 RO-WD239 -16 RO-WD297 DASH PART NO -20 RO-WD388 -14 RO-DS14 -24 RO-WD447 -16 RO-DS16 -32 RO-BE32* -18 RO-DS18 -20 RO-DS20 *NOTE: Seal is a circular cross -22 RO-DS22 section. -24 RO-DS24 -30 RO-DS30 -36 RO-DS36 -42 RO-DS42 -52 RO-DS52 RYCO 24·7 48 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL CONNECTOR TYPES - SOFT SEAL 51 BSPP PORT USE 52 BSPP: BRITISH STANDARD PIPE PARALLEL 53 METRIC PORT USE 54 DIN: DEUTSCHE INDUSTRIE NORMEN (GERMAN INDUSTRIAL STANDARD) DKOL & DKOS55 DKOL: METRIC LIGHT O RING SERIES 24° CONE 56 DKOS: METRIC HEAVY O RING SERIES 24° CONE ORFS 57 ORFS: O RING FACE SEAL RYCO RKVP/RKVF 58 RKVP: HIGH PRESSURE RKVF: HIGH FLOW STAPLELOK 59 SUPERLOK 60 SAE 61 MALE PILOT SWIVEL SAE: S OCIETY OF AUTOMOTIVE ENGINEERS 49 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

CONNECTOR TYPES - SOFT SEAL SAE 62 FEMALE PILOT SWIVEL SAE: SOCIETY OF AUTOMOTIVE ENGINEERS SAE FLANGE INTRODUCTION 63 CODE 61 64 SAE FLANGE TAPERED THREADS 65 CODE 62 66 SAE FLANGE METAL SEAL 67 CODE 62C 68 UNO 69 O RING BOSS UNO: U NIFIED NATIONAL, WITH O RING ISO 6149 ISO: INTERNATIONAL ORGANIZATION FOR 70 STANDARDIZATION PRESSURE WASHER SOFT SEAL 71 RYCO 24·7 50 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL BSPP BSPP: BRITISH STANDARD PIPE PARALLEL Sealing method: Soft seal at shoulder or 30° cone seat Thread form: 55° Thread standard: Whitworth ISO 228-1, BS 2779, AS 1722-2 BSPP threads are used as both general adaptors and as port adaptors. Soft sealing is usually required for port use. BS5200 allows for two sealing forms on the face of the female, Type C is conical and Type S is spherical. BSPP THREAD DASH BSPP MALE BSPP FEMALE SIZE & PITCH SIZE THREAD OD THREAD ID inch - TPI -02 mm inch mm inch 1/8 - 28 -04 9,6 0.38 8,6 0.34 1/4 - 19 -06 13,0 0.51 11,9 0.47 3/8 - 19 -08 16,5 0.65 15,2 0.60 1/2 - 14 -10 20,8 0.82 19,1 0.75 5/8 - 14 -12 22,8 0.90 20,8 0.82 3/4 - 14 -16 26,3 1.04 24,6 0.97 1 - 11 -20 33,1 1.30 30,7 1.21 1.1/4 - 11 -24 41,8 1.64 39,4 1.55 1.1/2 - 11 -32 47,7 1.88 45,5 1.79 2 - 11 -40 59,5 2.34 57,4 2.26 2.1/2 - 11 -48 75,1 2.95 72,6 2.86 3 - 11 87,9 3.46 85,4 3.36 51 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

BSPP INTRODUCTION FOR USE WITH O RING AND STEEL TAPERED THREADS RETAINING RING DIN 3852-2 METAL SEAL The thread run out is square to the shoulder. SOFT SEAL BSPP FORM A METAL BONDED SEAL DIN 3852-2 The bonded washer is held concentric to the thread by a shoulder cone. BSPP FORM B CUTTING SEAT DIN 3852-2, ISO 1179-4 The sealing face cuts into the seat. No soft sealing is used. BSPP FORM E ENCAPSULATED SEAL DIN 3852-2, ISO 1179-2 Grooved shoulder to suit DIN 3869 seal. BSPP TYPE O O RING SEAL BS5200 Female sealing face incorporates an O Ring groove for soft sealing. RYCO 24·7 52 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL METRIC DIN: DEUTSCHE INDUSTRIE NORMEN (GERMAN INDUSTRIAL STANDARD) Sealing method: Soft seal or metal seal at shoulder Thread form: 60º Thread standard: Metric ISO 261 Metric threads are used as both general adaptors and as port adaptors. Soft sealing is usually required for port use. Note: As these are port adaptors, some may not be provided with the internal profile to suit metric tube and cutting ring (as is depicted above). Table for ISO 9974-2, FORM E ENCAPSULATED SEAL MALE THREAD DASH LIGHT SERIES HEAVY SERIES OD & PITCH SIZE (L) DKL (S) DKS size pitch -10 3 3 M10 x 1,0 -12 3 3 M12 x 1,5 -14 3 3 M14 x 1,5 -16 3 3 M16 x 1,5 -18 3 3 M18 x 1,5 -20 3 M20 x 1,5 -22 3 M22 x 1,5 -26 3 3 M26 x 1,5 -27 3 M27 x 2,0 -33 3 3 M33 x 2,0 -42 3 3 M42 x 2,0 -48 3 M48 x 2,0 53 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

METRIC INTRODUCTION FORM A TAPERED THREADS METAL BONDED SEAL DIN 3852-1 METAL SEAL The bonded washer is held concentric to the thread by a shoulder cone. METRIC FORM B CUTTING SEAT DIN 3852-1, ISO 9974-3 The sealing face cuts into the seat. No soft sealing is used. METRIC FORM E ENCAPSULATED SEAL DIN 3852-11, ISO 9974-2 Grooved shoulder to suit ISO 9974-2 seal. SOFT SEAL RYCO 24·7 54 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL DKOL DKOL: M ETRIC LIGHT O RING SERIES 24° CONE Sealing method: 24° cone seat Thread form: 60° Thread standard: DIN 3853 24° cone seat: DIN 2353, ISO 8434-1 When a soft seal is used, an “O” is added to the acronym to signify an O Ring seal. CODE THREAD TUBE DKOL D SIZE & PITCH SIZE FEMALE 6L THREAD ID mm 8L size pitch mm 6,3 10L M12 x 1,5 6 mm 8,2 12L M14 x 1,5 8 10,5 10,2 15L M16 x 1,5 10 12,5 12,2 18L M18 x 1,5 12 14,5 15,2 22L M22 x 1,5 15 16,5 18,2 28L M26 x 1,5 18 20,5 22,2 35L M30 x 2,0 22 24,5 28,2 42L M36 x 2,0 28 28,0 35,4 M45 x 2,0 35 34,0 42,4 M52 x 2,0 42 43,0 50,0 55 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

DKOS INTRODUCTION DKOS: METRIC HEAVY O RING SERIES 24° CONE TAPERED THREADS Sealing method: 24° cone seat Thread form: 60° Thread standard: DIN 3853 24° cone seat: DIN 2353, ISO 8434-1 When a soft seal is used, an “O” is added to the acronym to signify an O Ring seal. DKOS METAL SEAL THREAD FEMALE CODE SIZE & PITCH TUBE SIZE THREAD ID D 6S size pitch mm mm mm SOFT SEAL 8S M14 x 1,5 6 12,5 6,3 10S M16 x 1,5 8 14,5 7,9 12S M18 x 1,5 10 16,5 10,0 14S M20 x 1,5 12 18,5 12,0 16S M22 x 1,5 14 20,5 14,2 20S M24 x 1,5 16 22,5 15,8, 25S M30 x 2,0 20 28,0 19,8 30S M36 x 2,0 25 34,0 24,5 38S M42 x 2,0 30 40,0 30,0 M52 x 2,0 38 50,0 36,8 RYCO 24·7 56 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL ORFS ORFS: O RING FACE SEAL Sealing method: O Ring Thread form: 60° Thread Standard: UN, UNF or UNS ISO 8434-3, SAE J1453 The ORFS system consists of an ORFS male with O Ring in the face, which seals against a flat seated ORFS female swivel nut fitting. The swivel nut can be slipped back to help installation in tight situations. The prominent position of the O Ring on the male fitting makes it easy to inspect the condition of the O Ring. ORFS THREAD DASH ORFS MALE ORFSFEMALE TUBE SIZE & PITCH SIZE THREAD OD THREADID SIZE inch - TPI mm inch mm inch Inch 9/16 - 18 UNF -09 14,3 0.56 12,9 0.51 1/4 11/16 - 16 UN -11 17,3 0.68 16,0 0.63 3/8 13/16 - 16 UN -13 20,6 0.81 19,1 0.75 1/2 25,4 1.00 23,6 0.73 5/8 1 - 14 UNS -16 30,0 1.18 28,2 1.11 3/4 1.3/16 - 12 UN -19 36,3 1.43 34,3 1.35 1 1.7/16 - 12 UN -23 42,7 1.68 40,6 1.60 1.1/4 1.11/16 - 12 UN -27 51,8 2.00 48,8 1.92 1.1/2 2 - 12 UN -32 57 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

RYCO RKVP/RKVF RKVP: HIGH PRESSURE RKVF: HIGH FLOW INTRODUCTION Sealing method: O Ring & Backup washer TAPERED THREADS Thread form: None The RKV male uses an O Ring and a backup washer which seals on the smooth bore of the female. The connection is held together by the shell and positively retained by the lock nut. RKV High Pressure (RKVP) and High Flow (RKVF) series’ are not interchangeable (including the shell). * F or various adaptors, the Lock Nut OD may vary from METAL SEAL standard (Coupling Lock Nut) OD to the values as listed. NOMINAL SIZE NUT OD OD COUPLING ADAPTOR* DN inch Dash mm inch mm inch mm inch SOFT SEAL HIGH PRESSURE - RKVP 10 3/8 -10 20 0.79 25 0.98 29 1.14 12 1/2 -12 24 0.94 30 1.18 34 1.34 19 3/4 -20 30 1.18 38 1.50 40 1.57 25 1 -25 36 1.42 45 1.77 47 1.85 31 1.1/4 -32 44 1.73 52 2.05 59 2.32 38 1.1/2 -40 54 2.13 64 2.52 72 2.83 51 2 -50 70 2.76 78 3.07 85 3.35 63 2.1/2 -63 84 3.31 98 3.86 110 4.33 HIGH FLOW - RKVF 25 1 -25 33 1.30 42 1.65 42 1.65 31 1.1/4 -32 39.8 1.57 50 1.97 50 1.97 38 1.1/2 -40 53 2.09 62 2.44 72 2.83 51 2 -50 65 2.56 75 2.95 80 3.15 63 2.1/2 -63 75 2.95 85 3.35 90 3.54 76 3 -75 99.3 3.91 110 4.33 125 4.92 RYCO 24·7 58 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL RYCOLOK Sealing method : O Ring & Backup washer Thread form: None Connection standard: DIN 20043, SAE J1467 The RYCOLOK male connector uses an O Ring and a backup washer which seals on the smooth bore of the female. The connection is held together by the staple. The male staple groove (G) aligns with the drilled holes of the female allowing the staple to be inserted. NOMINAL SIZE RYCOLOK STAPLE SIZE OD G G S S DN inch Dash mm inch mm inch mm inch 6 1/4 -06 15 0.59 5,1 0.20 8 0.31 10 3/8 -10 20 0.79 5,1 0.20 13 0.51 12 1/2 -12 24 0.94 5,1 0.20 17 0.67 16 5/8 -16 26 1.02 5,1 0.20 19 0.75 19 3/4 -20 29 1.14 5,1 0.20 22 0.87 25 1 -25 39 1.53 7,1 0.28 29 1.14 31 1.1/4 -32 46 1.81 7,1 0.28 36 1.42 38 1.1/2 -40 55 2.16 7,1 0.28 45 1.77 51 2 -50 64 2.52 7,1 0.28 54 2.13 63 2.1/2 -63 81 3.17 9,1 0.36 71 2.80 76 3 -75 94 3.67 ≥9,1 ≥0.36 78 3.07 59 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

SUPERLOK INTRODUCTION Sealing method: O Ring & Backup washer TAPERED THREADS Thread form: None The SUPERLOK male connector uses an O Ring and a backup METAL SEAL washer which seals on the smooth bore of the female. The connection is held together by the staple. The male staple groove (G) aligns with the drilled holes of the female allowing the staple to be inserted. SUPERLOK use different width staples than standard STAPLELOK and are therefore not interchangeable. NOMINAL SIZE SUPERLOK STAPLE SIZE OD G G S S DN inch Dash mm inch mm inch mm inch SOFT SEAL 19 3/4 -20 29 1.14 9 0.35 22 0.87 25 1 -25 39 1.53 13 0.51 29 1.14 31 1.1/4 -32 46 1.81 13 0.51 36 1.42 38 1.1/2 -40 55 2.16 13 0.51 45 1.77 51 2 -50 64 2.52 13 0.51 54 2.13 RYCO 24·7 60 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL SAE MALE PILOT SWIVEL SAE: SOCIETY OF AUTOMOTIVE ENGINEERS Sealing method: O Ring Thread form: 60° This connection is commonly used in air conditioning. The spigot length in front of the tube ‘bump’ is 4.83mm on the male version. Sealing is achieved by compressing an O Ring against the tube ‘bump’. The O Ring material is often Hydrogenated Nitrile Butadiene Rubber (HNBR). THREAD DASH MALE BEAD SPIGOT TUBE SIZE & PITCH SIZE THREAD OD DIA LENGTH SIZE inch - TPI mm inch mm mm inch 5/8 - 18 -10 15,9 0.63 13.2 4.83 -6 3/4 - 18 -12 19,0 0.75 16.2 4.83 -8 7/8 - 18 -14 22,2 0.88 19.6 4.83 -10 1.1/16 - 16 -17 27,0 1.06 23.1 4.83 -12 61 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

SAE FEMALE PILOT SWIVEL SAE: SOCIETY OF AUTOMOTIVE ENGINEERS Sealing method: O Ring INTRODUCTION Thread form: 60° This connection is commonly used in air conditioning. TAPERED THREADS The spigot length in front of the tube ‘bump’ is 9.91 mm on the female version. METAL SEAL Sealing is achieved by compressing an O Ring against the tube ‘bump’. The O Ring material is often Hydrogenated Nitrile Butadiene Rubber (HNBR). FEMALE THREAD DASH FEMALE BEAD SPIGOT TUBE SIZE & PITCH SIZE THREAD ID DIA LENGTH SIZE inch - TPI mm inch mm mm inch 5/8 - 18 -10 14,2 0.56 13.2 9.91 -6 3/4 - 18 -12 17,8 0.70 16.2 9.91 -8 7/8 - 18 -14 20,6 0.81 19.6 9.91 -10 SOFT SEAL 1.1/16 - 16 -17 24,9 0.98 23.1 9.91 -12 RYCO 24·7 62 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL SAE FLANGE CODE 61 L Bolt Sealing method: O Ring on flange face Retained by bolts UNC or Metric Thread form: Connection standard: ISO 6162, SAE J518 SAE Code 61 flanges are available in both metric and inch sizes, the difference being the bolt size used. The diameter of the fluid port is usually the nominal size of the flange. Code 61 flanges are used in pressure, suction and return applications. Be advised that O Ring dimensions may change between manufacturers. * Japanese version is JIS B 8363 Type I, (5/8” size added). NOMINAL FLANGE SIZE DASH SIZE DIAMETER (B) THICKNESS (T) BOLT CENTRES (F) BOLT CENTRES (G) inch mm inch mm inch mm inch mm inch 1/2 -08 30,2 1.19 6,73 0.265 17,5 0.69 38,1 1.50 5/8* -10 34,0 1.34 6,73 0.265 19,8 0.78 42,9 1.69 3/4 -12 38,1 1.50 6,73 0.265 22,2 0.88 47,6 1.88 1 -16 44,5 1.75 8,00 0.315 26,2 1.03 52,4 2.06 1.1/4 -20 50,8 2.00 8,00 0.315 30,2 1.19 58,7 2.31 1.1/2 -24 60,3 2.38 8,00 0.315 35,7 1.41 69,8 2.75 2 -32 71,4 2.81 9,53 0.375 42,9 1.69 77,8 3.06 2.1/2 -40 84,1 3.31 9,53 0.375 50,8 2.00 88,9 3.50 3 -48 101,6 4.00 9,53 0.375 61,9 2.44 106,4 4.19 63 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

INTRODUCTION TAPERED THREADS NOMINAL BOLT LENGTH METRIC BOLT BOLT LENGTH METAL SEAL FLANGE SIZE (L) (L) DASH SIZE UNC BOLT inch UNC inch Metric mm SOFT SEAL 1/2 -08 5/16 - 18 1.1/4 M8 x 1,25 35 5/8* -10 5/16 - 18 1.1/4 M8 x 1,25 35 3/4 -12 3/8 - 16 1.1/4 M10 x 1,5 35 1 -16 3/8 - 16 1.1/4 M10 x 1,5 35 1.1/4 -20 7/16 - 14 1.1/2 M10 x 1,5 40 1.1/2 -24 1/2 - 13 1.1/2 M12 x 1,75 45 2 -32 1/2 - 13 1.1/2 M12 x 1,75 45 2.1/2 -40 1/2 - 13 1.3/4 M12 x 1,75 45 3 -48 5/8 - 11 1.3/4 M16 x 2,0 45 RYCO 24·7 64 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL SAE FLANGE CODE 62 L Bolt High pressure modification of the Code 61 flange Sealing method: O Ring on flange face Retained by bolts UNC or Metric Thread form: Connection standard: ISO 6162, SAE J518 SAE Code 62 flanges are an isobaric version of the Code 61 flange. Isobaric means that the pressure rating is consistent across all sizes. All Code 62 flanges are rated to 400 bar / 5800 psi or greater. The Code 62 flanges are wider and thicker than Code 61 flanges. Code 62 are only used in pressure ports. Japanese version is JIS B 8363 Type II. NOMINAL FLANGE SIZE DASH SIZE DIAMETER (B) THICKNESS (T) BOLT CENTRES (F) BOLT CENTRES (G) inch mm inch mm inch mm inch mm inch 1/2 -08 31,7 1.25 7,75 0.305 18,2 0.72 40,5 1.59 3/4 -12 41,3 1.63 8,76 0.345 23,8 0.94 50,8 2.00 1 -16 47,6 1.88 9,53 0.375 27,8 1.09 57,2 2.25 1.1/4 -20 54,0 2.12 10,29 0.405 31,8 1.25 66,7 2.63 1.1/2 -24 63,5 2.50 12,57 0.495 36,5 1.44 79,4 3.13 2 -32 79,4 3.13 12,57 0.495 44,5 1.75 96,8 3.81 65 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

INTRODUCTION TAPERED THREADS NOMINAL BOLT LENGTH METRIC BOLT BOLT LENGTH METAL SEAL FLANGE SIZE (L) (L) UNC BOLT DASH SIZE inch UNC inch Metric mm SOFT SEAL 1/2 3/4 -08 5/16 - 18 1.1/4 M8 x 1,25 35 1 1.1/4 -12 3/8 - 16 1.1/2 M10 x 1,5 40 1.1/2 2 -16 7/16 - 14 1.3/4 M12 x 1,75 45 -20 1/2 - 13 1.3/4 M14 x 2,0 45 -24 5/8 - 11 2.1/4 M16 x 2,0 60 -32 3/4 - 10 2.3/4 M20 x 2,5 70 RYCO 24·7 66 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL SAE FLANGE CODE 62C L Bolt High pressure modification of the code 62 flange Sealing method: O Ring on flange face Retained by bolts Thread form: UNC or Metric SAE Code 62C flanges are a modification by Caterpillar® of the Code 62 flange. In all sizes, the flange thickness is 0,559”, (14,2mm). SAE Code 62C series flanges are isobaric which means that the pressure rating is consistent across all sizes. Code 62C flanges are visually thicker than standard Code 62 flanges. NOMINAL FLANGE SIZE DASH SIZE DIAMETER (B) THICKNESS (T) BOLT CENTRES (F) BOLT CENTRES (G) inch -12 mm inch mm inch mm inch mm inch 3/4 -16 41,3 1.63 14,20 0.559 23,8 0.94 50,8 2.00 1 -20 47,6 1.88 14,20 0.559 27,8 1.09 57,2 2.25 1.1/4 -24 54,0 2.12 14,20 0.559 31,8 1.25 66,7 2.63 1.1/2 -32 63,5 2.50 14,20 0.559 36,5 1.44 79,4 3.13 2 79,4 3.13 14,20 0.559 44,5 1.75 96,8 3.81 67 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

INTRODUCTION TAPERED THREADS NOMINAL UNC BOLT BOLT LENGTH METRIC BOLT BOLT LENGTH METAL SEAL FLANGE SIZE (L) (L) DASH SIZE inch UNC inch Metric mm SOFT SEAL 3/4 1 -12 3/8 - 16 1.3/4 M10 x 1,5 45 1.1/4 1.1/2 -16 7/16 - 14 1.3/4 M12 x 1,75 45 2 -20 1/2 - 13 2 M14 x 2,0 50 -24 5/8 - 11 2.1/2 M16 x 2,0 60 -32 3/4 - 10 2.3/4 M20 x 2,5 70 RYCO 24·7 68 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL UNO (O RING BOSS) UNO: UNIFIED NATIONAL, WITH O RING Sealing method: O Ring Thread form: 60° Thread standard: UNF or UNC Connection standard: ISO 11926, SAE J1926 Very commonly used as a port thread, the UNO, or O Ring Boss is a companion thread for JIC. In all sizes, it uses the same thread as the JIC. It seals with an O Ring compressed between the hex boss of UNO male and the 12°/15° tapered bore of the UNO female port. UNO THREAD DASH SAE UNO MALE UNO FEMALE SIZE & PITCH SIZE DASH THREAD OD THREAD ID inch - TPI mm inch mm inch 5/16 - 24 UNF -05 -02 7,9 0.31 6,9 0.27 3/8 - 24 UNF -06 -03 9,5 0.38 8,5 0.33 7/16 - 20 UNF -07 -04 11,1 0.44 9,9 0.39 1/2 - 20 UNF -08 -05 12,7 0.50 11,4 0.45 9/16 - 18 UNF -09 -06 14,3 0.56 13,0 0.51 3/4 - 16 UNF -12 -08 19,1 0.75 17,5 0.69 7/8 - 14 UNF -14 -10 22,2 0.88 20,3 0.80 1.1/16 - 12 UN -17 -12 27,0 1.06 24,9 0.98 1.3/16 - 12 UN -19 -14 30,2 1.19 28,2 1.11 1.5/16 - 12 UN -21 -16 33,3 1.31 31,2 1.23 1.5/8 - 12 UN -26 -20 41,3 1.63 39,1 1.54 1.7/8 - 12 UN -30 -24 47,6 1.88 45,5 1.79 2.1/2 - 12 UN -40 -32 63,5 2.50 61,5 2.42 69 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

ISO 6149 ISO: INTERNATIONAL ORGANIZATION FOR STANDARDIZATION Sealing method: O Ring INTRODUCTION Thread form: 60° Thread standard: ISO 261 TAPERED THREADS Connection standard: ISO 6149-1, SAE J2244/1, DIN 3852 Part 3 ISO 6149 is a modern port alternative. ISO 6149 is similar to UNO (O Ring Boss) except that the thread form is metric. *M14 x 1,5 is recommended for diagnostic port use. ISO 6149 THREAD ISO 6149 MALE ISO 6149 FEMALE METAL SEAL SIZE & PITCH THREAD OD THREAD ID SOFT SEAL size pitch mm mm M8 x 1,0 8,0 7,0 M10 x 1,0 10,0 9,0 M12 x 1,5 12,0 10,5 M14 x 1,5* 14,0 12,5 M16 x 1,5 16,0 14,5 M18 x 1,5 18,0 16,5 M22 x 1,5 22,0 20,5 M27 x 2,0 27,0 25,0 M33 x 2,0 33,0 31,0 M42 x 2,0 42,0 40,0 M48 x 2,0 48,0 46,0 M60 x 2,0 60,0 58,0 RYCO 24·7 70 THREAD IDENTIFICATION POCKET GUIDE

SOFT SEAL PRESSURE WASHER Sealing method: O Ring & Spherical Seat Commonly used on Karcher® industrial and domestic high pressure water cleaners. THREAD DASH SPIGOT SPHERICAL SIZE & PITCH SIZE DIAMETER SEAT size pitch -22 mm mm M22 x 1,5 14 5mm radius 71 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

SEAT ANGLE GAUGE 90º 45º 74º 37º 60º 30º To measure the seat angle, place part on page and match to the angle shown 72

THREAD PROFILES METRIC THREAD PROFILES DKM, DKL, DKS, DKOL, DKOS, JIS METRIC, ISO 6149 14mm 14 mm 16mm 16 mm 18mm 18 mm 22mm 22 mm 24mm 24 mm 26mm 26 mm 30mm 30 mm 36mm 36 mm 42mm 42 mm 52 mm 52mm 73 RYCO THREAD IDENTIFICATION POCKET GUIDE

THREAD PROFILES PIPE THREAD PROFILES MALE BSPP, BSPT & NPT -02 1/8” -04 1/4” -06 3/8” -08 1/2” -10 5/8” -12 3/4” -16 1” -20 1.1/4” -24 1.1/2” 2” -32 RYCO 24·7 74 THREAD IDENTIFICATION POCKET GUIDE

JSEAL™ THE NEW STANDARD  IN JIC FITTINGS LEAK FREE NO SWEATING NO WEEPING L RIGHTS RESERVALED PAT E N TE D NO STRETCHING NO CRACKING 75 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

ISOBARIC HOSE INTRODUCTION 1/2 BEND RADIUS TAPERED THREADS MILLION CYCLE METAL SEAL CHOOSE FROM OVER 100 PRODUCTS WITHIN THE ISOBARIC RANGE OF HOSES THAT WILL COVER ALL YOUR CONSTANT SOFT SEAL PRESSURE SYSTEM’S NEEDS. ALL OF THE RYCO ISOBARIC SPIRAL RANGE IS TESTED TO A MINIMUM OF ONE MILLION IMPULSE CYCLES TO DELIVER EXTENDED HOSE LIFE CYCLE, AND EXCEPTIONAL PERFORMANCE AND DURABILITY. 76Up to hHalfSeSArieEsmIsionbimaruicmSbpeirnadl arnaddiTu3s0Tf0oH0r RTseESreiAeriDsehsIoIDssoeEbsNaarTriecIFbteIrsaCtiedAdThtIooOseoNnaenPdmOHCillSKioeREnrYiTeimCsGOpIsUuo2lbIs4Dea·rEc7icycslpeisr.al hose.

RYCO HALP® HOSE ASSEMBLY LIFESPAN PREDICTOR RYCO HALP® is an online program that predicts the estimated lifespan of hose assemblies for given conditions and environments. 1. ASSET MANAGEMENT RYCO HALP® aids in determining the optimum time to carry out 4. REPORTING 2. AUDIT preventative maintenance by providing an estimated prediction 3. LIFE CYCLE MANAGEMENT when hose assemblies should be replaced before end of life. By being proactive RYCO HALP® assists in risk management and helps to prevent fluid injection injuries. RYCO HALP® links to the RYCO Asset Management (QRAM) database of hose assemblies, providing estimated predictive lifespan. When coupled with QRAM, RYCO HALP® keeps you on track with a scheduled hose maintenance solution. 77 RYCO 24·7 THREAD IDENTIFICATION POCKET GUIDE

HAVE HOSE ASSEMBLY VISUAL EVALUATION IT’S AS EASY AS 1-2-3! Free from obvious 1 external defects and/ or abnormalities. Non-urgent external 2 deterioration and/ or abnormalities that require the hose assembly to be scheduled for replacement at the next service. Urgent external 3 deterioration. Possible safety issue. Replace immediately. Hydraulic hose assemblies have a finite service life. This service life is dependent upon many factors that cannot be determined upon visual inspection alone. HAVE is a methodology of determining visual external defects, wear and tear, or abuse. HAVE does not provision or determine the portion of the hose assembly life that has been consumed. RYCO 24·7 78 THREAD IDENTIFICATION POCKET GUIDE

All Rights Reserved Copyright: March 2021 Released: March 2021 Part Number: RYCO-MKT0213 RHAU-MKT Thread ID Booklet 2021-05-13 V1-7