Tire Service & Alignment 2018

Tools & Equipment 02099 CV Boot Clamp Installation ToolDesigned for the low-profile clamps usedto hold CV Boots on FWD vehicles. The#02099 comes complete with a ratchet. Werecommend using this tool when installingour #87365 Crown Victoria Camber Kit. 37990 Ball Joint Separator This heavy duty, forged alloy steel, lever-type ball joint and tie rod end remover provides good leverage action to remove stubborn tie rod ends or break ball joint tapers easily. Use when space prevents use of a direct action separator. The #37990 fits 3/4” openings. 38620 CV Joint Fork When used with #499, this tool will pull most CV joints that use a hidden snap ring to hold them in the transaxle. Made to remove the axle assembly without damaging the transmission case or inside roller bearing. 40250 147 Internal Coil Spring Compressor 8/24/2018 5:17:51 PM A handy chrome-moly steel compressor designed to fit inside most coil springs with an internally mounted shock. Will accommodate spring lengths from 8 1/4” to 14”. It can be use on any coil springs with a mini- mum inside diameter of 3 3/8” to a maximum inside diameter of 5 5/8” and wire diameters up to 3/4”.#E - Alignment.indd 147

Tools & Equipment 40310 Tie Rod/Ball Joint/Pitman Arm Tool Kit Five tools in one, this handy kit consists of three drop forged forks and two handles. One handle is for use with a hammer and one is designed to fit an air hammer. All forks are threaded to interchange with either handle. Comes with 3 forks of 11/16”, 15/16” and 1 1/8” openings. 40910 Upper Control Arm Bushing Service Set Easily replace press-in type control arm bushings on many domestic and imported vehicles with this new kit. Mechanical power screw quickly and easily removes worn bushings and install them without damaging the control arm. Set includes C-Frame, screw assembly and all adapters to do the job quickly and correctly. 40920 40920 Performance Ball Joint Press This tool was specifically designed to remove the original equip- ment ball joints on smaller cars when installing SPC Performance’s sliding ball joints. With this revolutionary design you can remove the ball joint from the front upper control arm without removing the arm from the vehicle, saving time and costs. Packaged in a conve- nient blow-molded plastic case this set comes complete with adapt- ers for removing and installing stock or Specialty Product’s sliding ball joints. 45938 45938 Colorado/Canyon 4WD Alignment Socket Applications Chevrolet/GM: 2004 & up 4WD Aligning these trucks can be difficult because it is impossible Chevrolet Colorado, GMC Canyon to access the head of the cam bolt to adjust alignment angles. This special grooved socket fits over the end of the bolt al- lowing the technician to turn the alignment cams to change alignment angles after loosening the lock nut. This socket makes aligning these 4WD trucks much quicker and easier.148#E - Alignment.indd 148 8/24/2018 5:17:51 PM

Tools & Equipment 74400 74400 1½” Open End Wrench This wrench makes presetting the new adjustable truck sleeves, #24120, #24130, #24160, #24180, easier for the installer. When using the #74400 wrench it is recommended that the opening be equally positioned over the slot opening of the sleeve body. For #24160 - holds the outer body in position. For #24180 - holds the inner eccentric sleeve for adjustment. 74500 74500 1 ¼” Box End Wrench This wrench makes presetting the new adjustable truck sleeves, #24120, #24130, #24180, easier for the installer. Adjusts the inner sleeve. 72509 2WD/4WD Ball Joint Press Remove and replace universal joints without “brute force” meth- ods that can cause costly damage. Now you can take on 4WD ball joint service in addition to servicing most cars. A forcing screw-powered press, used with proper adapters, easily removes and installs all press-fit ball joints (includes GM plastic pin “U” type joints). 72509 74910 74910 Applications Cam Knock Out Punch Chevrolet/GM: 1988-1998 2WD/4WD C & K Series 1500, A necessary tool for removing the align- 2500, 3500 w/independent front ment inserts on the upper control arm suspensions; 1991 & up AWD alignment brackets without damaging the Astro Vans and AWD Safari bracket. The center punch is for the older Vans; 1992-1999 4WD V10, V20, GM vehicles and newer Jeep JKs and the V1500, V2500, Tahoe, Suburban; offset punch is for GM’s newer models. 1996-2002 2WD G10, G20, G30; CAUTION: Not for use with impact 1996-1999 2WD R10, R20, R30, wrenches (air tools). Tahoe; 1999-2001 Cadillac Escalde Jeep: 2007 & up JK 149#E - Alignment.indd 149 8/24/2018 5:17:52 PM

Tools & Equipment 76800 8 Piece 1/2” Torque Stick Set Part No. Description Color Green 76610 17mm nut, 55 ft/lbs torque Red Yellow 76615 17mm nut, 80 ft/lbs torque Blue Grey 76620 19mm nut (3/4”), 65 ft/lbs torque Brown Orange 76625 19mm nut (3/4”), 80 ft/lbs torque White 76630 19mm nut (3/4”), 100 ft/lbs torque 76635 13/16” nut, 100 ft/lbs torque 76645 21mm nut, 80 ft/lbs torque 76800 76650 7/8” nut, 120 ft/lbs torque 75555 75500 1/2” Heavy Duty Extension 4 Piece Torque Extension Set Part Description Color No. Part Description Color 75500 75555 140 ft/lbs torque Agua No. 75520 65 ft/lbs torque Yellow 75555 75525 80 ft/lbs torque Blue 75530 100 ft/lbs torque Grey 75550 120 ft/lbs torque White 76900 10 Piece 1/2” Torque Stick Set Part No. Description Color Green 76610 17mm nut, 55 ft/lbs torque Red 76615 17mm nut, 80 ft/lbs torque 76620 19mm nut (3/4”), 65 ft/lbs torque Yellow 76625 19mm nut (3/4”), 80 ft/lbs torque Blue 76630 19mm nut (3/4”), 100 ft/lbs torque Grey 76635 76640 13/16” nut, 100 ft/lbs torque Brown 21mm nut, 60 ft/lbs torque Black 76645 21mm nut, 80 ft/lbs torque Orange 76650 7/8” nut, 120 ft/lbs torque White 76900 76655 7/8”, 140 ft/lbs torque Aqua 8/24/2018 5:17:53 PM150#E - Alignment.indd 150

75915 Tools & Equipment Cutter 75915 This cutter is a necessary tool for cutting the EZ Shim. Its thin cutting blades minimize shim breakage. 77880ZZ Applications Ford / Dodge Combo Sleeve Puller Dodge: 2500 & 3500 Ford: Twin I-Beam w/upper & lower ball joints This sleeve puller will pull OE and most aftermarket camber/caster CAUTION: Not for use with impact wrenches sleeves quickly and efficiently, (air tools). usually without damaging the ears of the sleeve. Heat treated high strength steel. Single-unit design with no loose parts. 81139 Magnetic Adjustable Camber Gauge Has a simple leveling adjustment of ± 3º. Time/ 81139 money saving device. Return a strut to its original camber after repair or replacement. Measure amount of camber change movement before reinstalling alignment heads during camber kit installation. Check the amount of camber change before reinstall- ing tire and wheel assemblies on trucks receiving offset alignment bushings. 87175 Applications Truck Sleeve Socket Ford RWD: 1987-1996 F150, F250 (L/D), 1987 & up F250 This 1-1/2” socket is useful for (S/D), F350, 1992 & up E150, adjusting both the OEM and our E250, E350, 1989-1997 Ranger, popular #23130 and #23180 sleeve 1989-1990 Bronco II, 1991- series for Ford and Mazda RWD 1994 Explorer and 4WD trucks with pinch bolt Ford 4WD: 1990-1997 Ranger, style suspension. For 1/2” drives. 1991-1994 Explorer Mazda RWD/4WD: 1991-1994 Navajo, 1994-1997 Pickup 151#E - Alignment.indd 151 8/24/2018 5:17:56 PM

Tools & Equipment Rotary Files 85125 85125 85130 Steel File SetHigh quality carbide rotary files, ideal for elongating strutholes on many vehicles. Use when installing #82110,#82120 and #87350 adjusters. May be used with 1/4” or3/8” drills at high speeds.Includes 85137 85126 - 1/4” Rotary File (Max Speed 9,000 RPM) 85127 - 3/8” Rotary File (Max Speed 9,000 RPM) 85130 85128 - 5/8” Rotary File (Max Speed 7,000 RPM) 3/8” Rotary File Set 85137 This rotary file set is ideal for every Aluminum File technician. Be ready to elongate slots in Aluminum and Steel frames and bracketsThis 3/8” rotary file is specifically designed for Alumi- to accept larger offset cams. The kit in-num. Use it to quickly and cleanly expand cam slots in cludes one #85127 rotary file for steel, onealuminum brackets and frames. It is an ideal tool to use #85137 rotary file for aluminum, and cut-when installing SPC cams such as the #72050 or #72055 ting fluid to extend your rotary file’s life.in a 350Z. 88830 Ford / Dodge Sleeve Puller (Aftermarket)This puller is designed to CAUTION: Not for use withwork specifically with the impact wrenches (air tools).#23100 and #23120 sleeves.It will allow the technician 88830 is not recommended for useto pull the sleeves without on Ford Motor Company originalnormally breaking the ears off equipment sleeves. Use #77880the sleeve. for OEM sleeves. 89000 89105 - Dual socket inner tie rod removal tool, fits 1-3/16” or 1-5/16” hex inner tie Inner Tie Rod End Wrench Set rod ends on Fords and Chryslers with TRW racks. Set includes the 89105 89106 - A 1-3/16” hex tool for inner tie rod Dual Socket Inner Tie ends on Ford Escort, Tempo, Topaz, Lynx. Rod Removal Tool 89107 - A 1-5/16” hex tool designed for in- along with the 89106, ner tie rod ends on 1986 & up Taurus/Sable. 89107 and 89108 adapter sockets. 89108 - A 1-7/16” hex tool designed for GM Saginaw rack and pinions.152#E - Alignment.indd 152 8/24/2018 5:17:58 PM

Tools & Equipment 91000, 91010, 91025 & 91030 FasTraxTM Camber / Caster Gauge 91000 • 91000: Fits wheels 13” to 18” • 91010: Fits wheels 17” - 22” • 91025: Fits wheels 13” - 18” (Off-Road Applications) • 91030: No lip adapter • Portable, hands-free alignment can be done quickly and easily with the FasTraxTM Adjustable Camber/Caster Gauge. • Includes gauge and wheel mount (fits most wheels from 13” to 18”). • Displays Camber ±4º / Caster -4º to +12º. • Saves time and tires. • Accurate, rugged and easy-to-use. If you do any of these jobs, you need the FasTrax Camber/Caster Gauge! • Install adjustable control arms • Replace idler arms / tie rods ends • Replacing struts • Install adjustable bushings • Collision repair estimates • Fram straightening 91100 FasTraxTM Optional Toe Adapter Kit • Simply lower toe arms and insert tape measure into 91100 slot. Then measure to opposite tire reference point for accurate and fast toe readings. • Includes 2 arms and reinforcement blocks that install easily onto either the 91000 or the 91010. 75970 75970 Spacer Set (8) • This set (4 different sizes - 2 of each) aligns caliper to rotor after installation of a camber shim. • Specifically designed to be used with the EZ Shim when cor- recting some FWD cars with hub mounted rear disc brakes. 153#E - Alignment.indd 153 8/24/2018 5:18:06 PM

Tools & Equipment 77928ZZ 77928ZZ Brake Pedal Depressor • An adjustable steel plate extends the length of the bar to put constant pressure on the brake pedal. 77938 77938 Steering Wheel Holder• This tool securely holds the steering wheel and cov- ered hooks while the base prevents damage to the steering wheel or seat. EZREZLINE EZREZLINE Wheel Laser Alignment Tool DOWTC614 • All measurements can be taken in under 10 minutes. 8/24/2018 5:18:07 PM • E-Z precise axle and wheel alignment. • For heavy trucks, all type of trailers. • Compact design, easy transport and toolbox storage. • Multipurpose measurement capabilities. • A straight steel bar and bungee cord are all you need in addition to the EZ line, to set the toe on any vehicle, including trucks, that have an “in” or “out” toe setting. • Includes: 4 magnetic self-centering lasers, measuring tape, 2 magnetic 5th wheel pin adapters and durable storage/travel case.154 DOWTC614 Tomcat Camber Adjustment Tool • Makes camber adjustment a one-man job. • Works on many GM and Chrysler vehicles using two-bolt lower strut mounts. • Inflatable air bladder fits between tire and strut for easy and controlled adjustment of camber settings. • Camber can be easily set with wheels on the ground.#E - Alignment.indd 154

TOOLS & EQUIPMENT#F - Tools & Equipment.indd 155 8/27/2018 9:54:53 AM

Air Systems Air Compressors................................................157 Nitrogen Tire Filling Systems............................158 Air Hose & Reel............................................159-160 Air Regulators.....................................................161 Couplers & Plugs................................................162 Air Accessories..................................................163 Air Tools Impact Wrenches.........................................164-169 Air Ratchets........................................................170 Drills,Grinders,Hammers............................171-173 Tire Buffers..........................................................174 Air ToolAccessories....................................175-177 Wheel & Tire Service Tools Bead Breakers.............................................178-179 Mount/Demount Tools................................180-181 Tire Spreader.......................................................182 TorqueTools.................................................183-184 Shop Service Tools......................................184-185 Tire Gauges.........................................................186 Shop Equipment Bottle Jacks.................................................187-188 Service Jacks...............................................189-190 Wheel Dollies......................................................191 Tire Changers..............................................192-194 WheelBalancers................................................195-196 Lifts............................................................197-199 General...........................................................200-201 Mighty Tool Catalog...................................................202156#F - Tools & Equipment.indd 156 8/27/2018 9:54:53 AM

IMC218V Air Compressors Vertical Electric Compressor IMC218V IMC318VL • Start/Stop pressure switch control • Fully enclosed belt guard • Full 2 year bumper to bumper warranty • Horse Power: 5 • Pump: T29S • Motor Volt / Phase: 208-230/1 • Tank: 80 gallons • CFM Disp: 18.59 • ACFM@100/175 PSI: 15.33/13.75 • Max PSI: 175 IMC318VL Vertical Electric Compressor • Start/Stop pressure switch control • Fully enclosed belt guard • Full 2 year bumper to bumper warranty • Horse Power: 7.5 • Pump: T39 • Motor Volt / Phase: 208-230/1 • Tank: 80 gallons • CFM Disp: 32.52 • ACFM@100/175 PSI: 25.25/22.28 • Max PSI: 175#F - Tools & Equipment.indd 157 157 8/27/2018 9:54:55 AM

Nitrogen Tire Filling Systems N2-900 N2-93025 Gallon Tank, 170 lbs 52 Gallon Tank, 170 lbs15-25 Vehicles per day 15-25 Vehicles per dayCompact Size Compact Size(22” x 17” x 47”) (22” x 17” x 47”)• Five tire hook-up• Makes 95-97% nitrogen• Vacuums tires before filling• Easy two valve operation• Auto shut-off when nitro tank is full• Whole process takes only minutes• All four tires can be inflated at once• The machine only needs shop air; no electrical power N2-930158 NTF-515 NTF-515#F - Tools & Equipment.indd 158 15 Gallon Tank, 206 lbs 20-35 Vehicles per day Compact Size (26” x 25” x 61”) • Application flexibility - dual settings pro- vides either 95% or 98% N2 purity at the outlet with the twist of the wrist • Superior productivity - automatic operation, up to six tire simultaneous fill • Super-fast service times - about 7 minutes for four 225/60R15 tire simultaneously • Use anywhere - battery powered fill control- ler provides superior unit portability • Fill versatility - programmable control head easily accommodates variable pressure set- tings 8/27/2018 9:54:56 AM

Air Hoses Reinforced Air Hose • Heavy duty, non-kink reinforced air hose performs flawlessly in all conditions • Especially designed to withstand the wide range of weather and abrasion condition experienced by today’s active repair facilities 891G 891ZZ Part No. Description Color Length Hose ID (feet) (inch) 890ZZ Reinforced air hose with ¼” NPT male ends Red 891ZZ Reinforced air hose with ¼” NPT male ends Red 25 ⅜ 892ZZ Reinforced air hose Red 50 ⅜ 893Z Reinforced air hose with ¼” NPT male ends Red 500 ⅜ Reinforced air hose with ½” NPT male ends Red 35 ⅜ 895 Reinforced air hose Red 50 ½ 896Z Reinforced air hose with ¼” NPT male ends Green 500 ½ 890G Reinforced air hose with ¼” NPT male ends Green 25 ⅜ 891G Reinforced air hose with ¼” NPT male ends Green 50 ⅜ 893G 35 ⅜ Polyurethane Coil Hose • Heavy duty, non-kink reinforced air hose performs flawlessly in all conditions • Especially designed to withstand the wide range of weather and abrasion condition experienced by today’s active repair facilities Part No. Description Length Hose ID (feet) (inch) 840P Polyurethane coil hose with ¼” male ends 841P Polyurethane coil hose with ¼” male ends 12 ¼ 842P Polyurethane coil hose with ¼” male ends 25 ¼ 843P Polyurethane coil hose with ¼” male ends 50 ¼ 844P Polyurethane coil hose with ¼” male ends 25 ⅜ 50 ⅜ 841P 159#F - Tools & Equipment.indd 159 8/27/2018 9:54:57 AM

Air Hoses & Air Reels Nylon Coil Hose • Self-retracting and abrasion-resistant. • Recoils to original size. Part Number Description Length Hose ID (feet) (inch) MTN6375 Nylon coil hose with ¼” MIL1669 Nylon coil hose with ¼” 12 ¼ 25 ¼ Impact Tool Air Hose • Red rubber air hose with brass ferrule • Rated at 300 PSI working pressure • PCV Bend Restrictors Part Number Description Length Hose ID (feet) (inch) KTI72005 Impact Tool Air Hose with ½” NPT male fitting KTI72006 Impact Tool Air Hose with ½” NPT male fitting 25 ½ 50 ½ LIN83753 LIN83754 Air Reel - 50’ x 3/8” Air Reel - 50’ x 1/2” • All steel construction with hose LIN83753 • Slotted mounting base - easy 8/27/2018 9:54:59 AM installation • Spring powered automatic recoil • 8 position ratchet system - easy positioning of hose • 5 position adjustable outlet arm • 300 PSI maximum pressure • 35 CFM maximum air flow160#F - Tools & Equipment.indd 160

AST2615 Air Regulators3/8” NPT Filter with Regulator and Gauge AST2615• Prevents costly damage to air tools caused by rust, scale and moisture• Convenient minimum installation time into your compressed air system• Gauge has rugged polycarbonate case with 2” face• 3/8” NPT with 0-160 PSI gauge AST2616 AST2616 Filter / Regulator and Lubricator with Gauge DEVDAD500 • Prevents costly damage to air tools caused by 161 rust, scale and moisture 8/27/2018 9:55:00 AM • Convenient minimum installation time into your compressed air system • Gauge has rugged polycarbonate case with 2” face • 3/8” NPT with 0-160 PSI gauge DEVDAD500 Desiccant Air Filter • Eliminates costly redos due to moisture and dirt in the air line; three stage drying and filtering • First stage centrifugal filter removes oil, water and dirt down to 5 microns • Second stage coalescer filter removes oil aerosols and dirt particles down to .01 microns • Third stage uses low-dusting desiccant to trap water vapor • 25 CFM capacity.#F - Tools & Equipment.indd 161

Couplers & Plugs Part No./Desc Product Qty/ Dia. 31 Inc. Acme Amflo Camel Dill Milton NAPA Schrader Tru-Flate 2121 Box NPT Tru-Flate Male Coupler 5 ¼ 17-336 A926B C-1 524 D-12 786 4-674 3503 13-124 2122 Tru-Flate 5 ¼ 17-326 A925B C-2 523 D-13 785 4-675 3504 13-134 Female Coupler 2124 5 ¼ 17-340 --- C-2R 545 D-13R 787 --- 3505 13-136 Tru-Flate T Female Ring Sleeve 5 ¼ 17-364 --- C-9 564 D-16 1816 4-678 3511 13-704 R 2155 U Tru-Flate 5 ¼ 17-363 A942B C-10 563 D-17 1815 4-679 3512 13-712 - Female Coupler F 2156 2 ½ 17-224 A928N CP-1 538 D-2C 783 4-685 3506 12-124 L Tru-Flate A Female Ring Sleeve 2 ½ 17-234 A929N CP-2 539 D-3C 784 4-686 3507 12-134 T 2221 E Tru-Flate 5 ½ 17-263 A942N CP-9 568 D-2F 1817 4-689 3513 12-704 Male Coupler A 2222 5 ½ 17-264 A943N CP-10 569 D-3F 1818 4-690 3514 12-712 R Tru-Flate O Female Coupler 5 ¼ 17-348 --- C-37 527 --- 776 4-6603 3525 13-324 2255 I Tru-Flate 5 ¼ 17-342 A918B C-38 526 8888 775 4-820 3526 13-334 N Male Nipple D 2256 5 ¼ 17-221 A914N CP-37 528 8891 777 4-821 3529 12-324 U Tru-Flate S Female Nipple 5 ¼ 17-231 A916N CP-38 529 8889 778 4-822 3530 12-334 T 2131 R ARO 5 ¼ 17-332 A938B C-21 574 10003 716 4-6602 5141-12 13-224 I Male Coupler A 2132 5 ¼ 17-322 A937B C-20 573 10002 715 4-6601 5142-12 13-234 L ARO Female Coupler 5 ¼ 17-222 A910N CP-21 578 10010 727 4-6610 5138-11 12-224 L 2231 I ARO 5 ¼ 17-232 A911N CP-20 579 10009 728 4-6611 5139-11 12-234 N Male Nipple C 2232 5 ¼ 17-313 A935B4M C-27 61-486 --- 790 --- 3527 13-424 O ARO L Female Nipple 5 ¼ 17-312 A935B4F C-28 61-548 --- --- --- 3528 13-434 N 2139 Industrial 5 ¼ 17-212 A935N4M CP-27 61-550 --- 791 --- 3531 12-424162 Male Coupler 2140 5 ¼ 17-213 A935N4F CP-28 61-551 --- 792 --- 3532 12-434 Industrial Female Coupler 2239 Industrial Male Nipple 2240 Industrial Female Nipple 2135 Lincoln Male Coupler 2136 Lincoln Female Coupler 2235 Lincoln Male Nipple 2236 Lincoln Female Nipple#F - Tools & Equipment.indd 162 8/27/2018 9:55:00 AM

Air Accessories Air Chucks Part No. Description 765 Ball Chuck, 1/4” NPT female (closed) 762ZZ 765 766 Ball Chuck, clip-on type, 1/4” NPT male barb (closed) 763ZZ 766 766-O Ball Chuck, clip-on type, 1/4” NPT 17-503 male barb (open) 762ZZ Euro-Style clip-on Air Chuck 772 763ZZ Dual Foot Lock on Air Chuck 773 772 Dual Foot Air Chuck 773 Air Chuck, Lock on 17-501 Ball Foot Chuck (closed) 17-501N Nitrogen Ball Foot Chuck (closed) 17-503 Ball Foot Chuck with Clip (closed) 17-501N 17-503FT Ball Foot Chuck with Clip (open)17-501 17-503FT 14-318R 14-318S 14-318H Air Regulator Air Regulator Swivel Hose • ⅜” Barbed Swivel • ¼” NPT• Hose Size 24” x ⅜” • Inlet size ¼” (M) NPT• ¼” NPT • Outlet size ¼” (F) NPT 14-318S 14-318H 14-318R 17-907 17-907M Air Blow Gun Air Blow Gun • Lever-Type Air Blow Gun • Lever-Type Air Blow Gun • Rubber Tip • Metal Tip 17-907 17-907M#F - Tools & Equipment.indd 163 163 8/27/2018 9:55:03 AM

Impact Wrenches CPT734H CPT734H CPT7733 1/2” Drive Extra Heavy Duty Air Impact Wrench CPT7733-2 • Differential regulator allows the operator to match the required power to the job • Improved oil bath DYNA-PACT clutch delivers higher performance and extended durability • Handle exhaust directs air away from the work piece and operator • Integral 360º air inlet swivel keeps air hose from being twisted and kinked • Working torque: 25-310 ft/lbs. • Max torque: 425 ft/lbs. • Weight: 5.13 lbs. CPT7733 1/2” Drive Heavy Duty Air Impact Wrench • Patented clutch provides smooth operation and extreme durability • Comfort and control with new ergonomic grip and trigger • Low air consumption and high torque makes this tool the most efficient in its class • Working torque: 25-400 ft/lbs. • Max torque: 550 ft/lbs. • Weight: 5.6 lbs. CPT7733-2 1/2” Drive Heavy Duty Air Impact Wrench with 2” Extended Anvil • Patented clutch provides smooth operation and extreme durability • Comfort and control with new ergonomic grip and trigger • Low air consumption and high torque makes this tool the most efficient in its class • Working torque: 25-400 ft/lbs. • Max torque: 550 ft/lbs.164 • Weight: 5.85 lbs.#F - Tools & Equipment.indd 164 8/27/2018 9:55:04 AM

IRT231C Impact Wrenches 1/2” Drive Super Duty Impactool™ IRT231C IRT231HA-2 • IR Twin Hammer MechanismTM • Adjustable Power Regulator • Pressure Feed Lubrication • Working torque: 25-350 ft/lbs. • Max torque: 600 ft/lbs. • Weight: 5.8 lbs. IRT231HA-21/2” Drive Super Duty Impact Wrench with 2” Extended Anvil • In-handle exhaust directs air away from user • Contoured comfort handle • Pressure Feed Lubrication • Adjustable power regulation • Working torque: 25-350 ft/lbs. • Max torque: 590 ft/lbs. CPT7722 CPT7722 3/8” Drive Butterfly Impact Wrench 165 • Rocking dog clutch for smooth operation 8/27/2018 9:55:06 AM and extreme durability • Easy maneuvering with 360º swivel air inlet • Built in regulator for controlled torque • Butterfly throttle for comfort and control • Made of durable aluminum body housing and is strongest in its class • Working torque: 5-50 ft/lbs. • Max torque: 90 ft/lbs.#F - Tools & Equipment.indd 165

Impact Wrenches IRT215 CPT772H IRT212 CPT7763-6 3/8” Drive Super Duty Air Impactool™ • More torque and less vibration • Unaffected by air press changes • Built-in power regulator prevents over torquing • Working torque: 20-150 ft/lbs. • Max torque: 180 ft/lbs. • Weight: 2.89 lbs. CPT772H 3/4” Drive Super Duty Air Impact Wrench • One hand push button forward/reverse power regulator • 4 position power settings in forward and ultimate power in reverse • Handle exhaust with 360º air inlet swivel • Working torque: 150-700 ft/lbs. • Max torque: 1,000 ft/lbs. • Weight: 10.5 lbs. CPT7763-6 3/4” Drive Heavy Duty Impact Wrench with 6” Extended Anvil166 • Twin hammer high performance clutch for longer life under tough conditions • Efficient 6 Vane Motor - power with any 1/2” hose air supply • 3 Position regulator and directional control • Handle exhaust keeps exhaust away from the operator • Working torque: 100-950 ft/lbs. • Max torque: 1,200 ft/lbs.#F - Tools & Equipment.indd 166 8/27/2018 9:55:07 AM

IRT261 Impact Wrenches 3/4” Drive Super Duty Air IRT261 Impact Wrench IRT261-3• Jumbo hammer mechanism• Compact with handle exhaust• Trouble-free, longer performance aided by the pressure-feed lube system• Working torque: 200-900 ft/lbs.• Max torque: 1,100 ft/lbs.• Weight: 12.4 lbs. IRT261-3 3/4” Drive Super Duty Air Impact Wrench with 3” Extended Anvil• Jumbo hammer mechanism• Compact with handle exhaust• Trouble-free, longer performance aided by the pressure-feed lube system• Working torque: 200-900 ft/lbs.• Max torque: 1,100 ft/lbs.• Weight: 13 lbs. IRT261-6 IRT261-6 3/4” Drive Super Duty Air Impact Wrench with 6” Extended Anvil• Jumbo hammer mechanism• Compact with handle exhaust• Trouble-free, longer performance aided by the Pressure-Feed Lube System• Working torque: 200-900 ft/lbs.• Max torque: 1,100 ft/lbs.• Weight: 13.7 lbs.#F - Tools & Equipment.indd 167 167 8/27/2018 9:55:07 AM

Impact Wrenches CPT7600-R CPT7773 CPT7600-R CPT7782-6 Pistol Grip Pneumatic Torque Wrench 8/27/2018 9:55:09 AM • Sets precise torque on wheels • Simple swing bar reaction mechanism for easy alignment and quick operation • Shut off mechanism eliminates torque varia- tion from air pressure changes or need for a separate pressure regulator. • Working torque: 350-660 ft/lbs. • Max torque: 1,200 ft/lbs. • Weight: 27 lbs. CPT7773 1” Drive Heavy Duty Air Impact Wrench • Twin Hammer high performance clutch for longer life under tough conditions • Efficient 6 Vane Motor - power with any 1/2” hose air supply • 3 position regulator & directional control - one lever for all controls with three positions in forward and reverse • Working torque: 100-950 ft/lbs. • Max torque: 1,200 ft/lbs. • Weight: 12.05 lbs. CPT7782-6 1” Drive Heavy Duty Impact Wrench with Extended Anvil • Pinless closed reinforced rocking dog impact mechanism • Socket retainer ring combined with hole retainer • Full teasing trigger • Regulator with integrated forward/re- verse with 3-position power settings in both directions • Working torque: 440-1,850 ft/lbs. • Max torque: 2,140 ft/lbs.168 • Weight: 25.6 lbs.#F - Tools & Equipment.indd 168

IRT271 Impact Wrenches 1” Drive Super Duty Air IRT271 Impact Wrench • Pressure-feed lube system for longer life service • Impressive power-to-size ratio • Dead handle improves operator control • Working torque: 200-900 ft/lbs. • Max torque: 1,100 ft/lbs. • Weight: 12.5 lbs. IRT285B-6 IRT285B-61” Drive Heavy Duty Air Impact Wrench with 6” Extended Anvil• New fast torque feature• Improved feather-tough trigger• Increased pressure rating can withstand 120 PSI for better durability• Working torque: 100-1,000 ft/lbs.• Max torque: 1,770 ft/lbs.• Weight: 27.3 lbs. IRT2190TI-6 IRT2190TI-6 1” Drive Titanium Air Impact Wrench with 6” Extended Anvil• Perfect for applications where high quality is essential• Reduced vibration• Extended robust anvil bushing provides long life under heavy shop usage• Working torque: 150-1,200 ft/lbs.• Max torque: 1,600 ft/lbs.• Weight: 15.5 lbs.#F - Tools & Equipment.indd 169 169 8/27/2018 9:55:10 AM

Ratchets CPT7823 CPT7823 IRT1105MAX-D2 1/4” Drive Compact Ratchet with 4 Position Swivel Head • 4 position swivel head for easy access and maneuverability • Compact & lightweight • Rear exhaust • 250 RPM of speed • Working torque: 15 ft/lbs. IRT1105MAX-D2 1/4” Drive Composite Air Ratchet• MAX power - 300 RPM free speed deliver• MAX control - Variable-speed regulator is hand-operable• MAX comfort - Ergonomic coupling nut and composite handle ensure operator comfort even during extended use• Working torque: 30 ft/lbs. CPT7830Q 3/8” Drive Super Duty “Quiet” Air Ratchet • Unique, adjustable noise con- CPT7830Q trol with no loss of power • Tri-Spring ratchet head • Lightweight and well balanced • Working torque: 10-90 ft/lbs. IRT107XPA IRT107XPA 3/8” Drive Air Ratchet • Variable speed lever-style throttle • 360º adjustable exhaust directs air away • Working torque: 54 ft/lbs. IRT109XPA IRT109XPA170 3/8” Drive Super Duty Air Ratchet • 220 RPM of free speed • 360º adjustable exhaust directs air away • Working torque: 76 ft/lbs.#F - Tools & Equipment.indd 170 8/27/2018 9:55:11 AM

CPT789R-26 Drills 3/8” Chuck Super Duty CPT789R-26 Reversible Drill IRT7802RA • Teasing throttle for precise control CPT789HR • Oil free operation • Needle bearing gearing for improved durability IRT7803R • Applications: Screwdriving, honing, and heavy 171 drilling • RPM: 2,600 8/27/2018 9:55:13 AM • Weight: 2.5 lbs. IRT7802RA 3/8” Chuck Heavy Duty Reversible Drill • Reversible motor with a quick reverse lever • Variable speed throttle for starting holes easily • Handles smoothly; a lightweight compact drill • RPM: 2,000 • Weight: 2.5 lbs. CPT789HR 1/2” Chuck Super Duty Reversible Air Drill • Teasing throttle for precise control • Oil free operation • Needle bearing gearing for improved durability • Applications: Heavy drilling, reaming, hole sawing and jobs requiring a lot of torque • RPM: 500 • Weight: 3.25 lbs. IRT7803R 1/2” Chuck Heavy Duty Reversible Drill • Quick reverse lever • Variable speed throttle • Heavy duty ball and needle bearing • RPM: 400 • Weight: 3.3 lbs.#F - Tools & Equipment.indd 171

Grinders CPT7500D CPT7500D 2” Angle Grinder / Cut-off Tool• Compact and lightweight for easy access in tight areas• Full 180 degree protective guard• Wheel size: 2 in.• RPM: 22,000• Weight: 1.2 lbs. CPT874 General Duty High Speed Cut-off Air Tool • Built-in regulator matches speed to job CPT874 • Lock off throttle to prevent accidental start up • Rear exhaust directs air away from work area IRT326 • Wheel size: 2 7/8 in. • RPM: 22,000 • Weight: 1.75 lbs. Heavy Duty Air Cut-off Tool IRT326 • Contoured level throttle with positice self-locking action • Built in speed regulator • Wheel size: 2-7/8 in. • RPM: 18,000 • Weight: 2.3 lbs. CPT854 4” Heavy Duty Air Angle Grinder CPT854 • Aluminum alloy housing is rugged yet lightweight • Removable dead handle • Spiral bevel gearing in angle head provides extended life and smooth vibrations • Wheel size: 4 in. • RPM: 12,000 • Weight: 3.75 lbs. IRT3445MAX Super Duty Air Angle Grinder172 IRT3445MAX • MAX power - featuring a mighty 0.88 horsepower mo- tor • MAX safety - internal to the tool is a governor • Built-in lubricating which optimizes the life of the angle gear set • Wheel size: 4.5 in. • RPM: 12,000 • Weight: 3.5 lbs.#F - Tools & Equipment.indd 172 8/27/2018 9:55:14 AM

Hammers CPT7110K CPT7110K Heavy Duty Air Hammer Kit IRT121K6• Includes (1) quick change retainer, (4) chisels, Air Chisel Open Stock and heavy duty carrying case Part No. Description• Vibration isolation system KTI81972 6” Cold Chisel• Touch trigger for precision start ups and total KTI81973 8” Cold Chisel KTI81975 Rivet and Bolt Cutter control KTI81976 Scraper• Weight: 4.5 lbs. KTI81979 3/8” Tapered Punch KTI81981 Hammer IRT121K6 KTI81995 Tie Rod Separators KTI81996 Ball Joint Separators Super Duty Air Hammer Kit• Includes (6) chisels and blow molded case• Hammer delivers up to 3,000 blows per minute• Professional touch trigger for total control• Weight: 3.5 lbs. IRT9500 5 Piece Chisel Set IRT9500 KTI81996 KTI81972#F - Tools & Equipment.indd 173 173 8/27/2018 9:55:15 AM

Tire Buffers CP-873K IRT327LS CP-873K Slow Speed Tire Buffer • Quick release chuck • Rear exhaust system • RPM: 2,800 • Weight: 2.25 lbs. IRT327LS Low Speed Tire Buffer • Lever-style tease trigger with lock-off • Quick change chuck for easy buffing wheel change • Piped-away exhaust • RPM: 3,000 • Weight: 1.1 lbs. CP-871 CP-871 High Speed Tire Buffer • Built-in regulator • Jacob’s chuck for holding buffing accessories • Lock off throttle to prevent accidental start ups • Rear exhaust system • RPM: 2,200 • Weight: 1.75 lbs. IRT327 IRT327 Heavy Duty High Speed Tire Buffer • Lever throttle for easy operation • Rear exhaust keeps air away from you and your work • RPM: 2,200 • Weight: 1.6 lbs.174 8/27/2018 9:55:16 AM#F - Tools & Equipment.indd 174

Air Tool Accessories AST78803 AST78803 4 Piece 1/2” Drive Thin Wall Flip Impact Socket Set with Protective Sleeves• Set includes sizes: 17mm x 19mm; 3/4” x 13/16”; 7/8” x 21mm• Includes 3” extension bar• Made of industrial grade chrome molybdenum steel alloy CPTSS4211WP CPTSS4211WP SUN2843 11 Piece 1/2” Drive Metric and SAE Wheel Nut Protector Impact Socket Set SUN4011M 175 • Set includes sizes: 3/4”, 13/16”, 7/8”, 15/16”, 1”, 1 1/16”, 17mm, 19mm, 21mm, 22mm and 23mm SUN2843 3 Piece 1/2” Drive 150mm Wheel Protector Impact Socket Set • Set includes sizes: 17mm, 19mm and 21mm • Services the most popular size lug nuts in the performance market SUN4011M 11 Piece 3/4” Drive Deep SAE Truck Impact Socket Set• Set includes sizes: 8 Deep Sockets: 27mm, 30mm, 32mm, 33mm, 35mm, 36mm, 38mm, 41mm; 3 Square Sockets: 17mm, 20mm, 21mm• Made of industrial grade chrome molybdenum alloy steel• Radius corner design - to extend the life of fasteners#F - Tools & Equipment.indd 175 8/27/2018 9:55:18 AM

Air Tool Accessories SUN4682 SUN4682 SUN5690A 11 Piece 3/4” Drive Truck Service Impact Socket Set KNK29KK5DB• Set includes sizes: 3/4”, 16/16”, 7/8”, 15/16”, 1”, 1 1/16”, 1 1/8”, 1 3/16”, 1 1/4”, 1 1/2” standard sockets and a 13/16” square socket• Made of industrial grade chrome molybdenum alloy steel• Radius corner design - to extend the life of fasteners SUN5690A 10 Piece 1” Drive SAE / Metric Heavy Duty Wheel Impact Socket Set • Set includes sizes: Deep: 33mm, 1”, 1 3/16”, 1 3/4”: Thin wall deep: 1 1/16”, 1 1/8”, 1 1/4”; Square: 13/16”, 15/16”; Controlled depth: 1 1/2” • Made of industrial grade chrome molybdenum alloy steel • Radius corner design - to extend the life of fasteners KNK29KK5DB 29 Piece Fractional Jobber Length Drill Bit Buddy Set • For jobber length drills from 1/16” through 1/2” by 64ths • Waterproof, great for outdoor worksites • No center punch or pilot hole required • Rounder, more accurate holes • Made in the USA Flip Sockets Part No. Description Size 14-847A TDFS-M TDFS-M Flip Socket, Metric 19mm x 21mm TDFS-S Flip Socket, Standard 3/4” x 13/16” 14-846 Flip Socket, Thin Wall 3/4” x 13/16” 14-846A Flip Socket, Extra Thin Wall 3/4” x 13/16” 14-847 Flip Socket, Thin Wall 19mm x 21mm 14-847A Flip Socket, Extra Thin Wall 19mm x 21mm176#F - Tools & Equipment.indd 176 8/27/2018 9:55:20 AM

Air Tool Accessories 3MTM Green CorpsTM RolocTM Discs• 3 Dimensional non-woven fiber material• Resists loading and clogging when removing greasy gasket material• For fast removal of cut gasket, residual adhesives, rust and debris and form-in-place gasketing com- pounds prior to assembly Part No. Description 1397-25 1396-25 2” 3MTM Coarse Brown 1397-25 2” 3MTM Medium Maroon 3MTM RolocTM Surface Conditioning Discs Part No. Description 7481-25 7480-25 2” 3MTM Coarse Brown 7481-25 2” 3MTM Medium Maroon 7485-25 3” 3MTM Coarse Brown 7486-25 3” 3MTM Medium Maroon AT032 AT032 Air Tool Oil • (12) 4 oz. bottles • Specially formulated for use in all piston-type and rotary air tools or in-line air lubricators • Prevents rust • Assures maximum tool performance#F - Tools & Equipment.indd 177 177 8/27/2018 9:55:21 AM

Bead Breaking Tools KEN35327 KEN35429 KEN32126 KEN35329 KEN35129 KEN35926 Part No. Replacement Length Weight Handle Wood Handled Wedges KEN35327 T11DH 17” (43.2cm) 4 3/4 lbs. KEN35329 T11EH 30” (76.2cm) 8 1/2 lbs. Fiberglass Handled Wedges KEN35427 TG11HD 18” (45.7cm) 4 3/4 lbs. KEN35429 TG11EH 32” (81.3cm) 8 1/2 lbs. Hickory Replacement Handles KEN35127 17” (43.2cm) 3/4 lbs. KEN35129 30” (76.2cm) 1 1/4 lbs. Fiberglass Replacement Handles KEN35227 18” (45.7cm) 2 1/2 lbs. KEN35229 33” (81.3cm) 3 lbs. Bead Breaking Tools KEN32126 For Trucks & 11 3/4” (29.9cm) 3 3/4 lbs. Bus Beads Impact Bead Breaker KEN35926 Heavy Duty 50” - 80” 24 lbs. (127.0cm - 203.2cm)178#F - Tools & Equipment.indd 178 8/27/2018 9:55:22 AM

Bead Breaking ToolsPart No. Length Stock WeightStraight Tire SpoonsKEN32119 24” (61.0cm) 11/16” (17.5mm) 2 1/2 lbs. KEN32102 KEN32106KEN33219 30” (76.2cm) 11/16” (17.5mm) 3 lbs. KEN32109 KEN32121Curved Tire SpoonsKEN32102 18” (45.7cm) 11/16” (17.5mm) 1 3/4 lbs.KEN32120 24” (61.0cm) 11/16” (17.5mm) 2 1/4 lbs.KEN33220 30” (76.2cm) 11/16” (17.5mm) 3 lbs.Drop-Center Tire SpoonsKEN34121 24” (61.0cm) 11/16” (17.5mm) 2 1/2 lbs.KEN32121 18” (45.7cm) 11/16” (17.5mm) 1 3/4 lbs.Mount/Demount Tire ToolKEN32106 16 1/2” (42.0cm) 5/8” (16.0mm) 1 1/2 lbs.KEN32109 9” (23.0cm) 7/16” (11.0mm) 0.4 lbs.Standard & Heavy Duty Tubeless Tire MountingKEN34645 37” (94.0cm) 3/4” (19mm) 4 1/2 lbs.KEN34647 41” (104.1cm) 7/8” (22mm) 7 lbs.KEN34747 36” (91.4cm) 3/4” (19mm) 4 1/2 lbs.KEN34847 52” (132.1cm) 1” (25mm) 7 lbs. KEN34747 KEN34645KEN34847 AMN71600 AMN71600 Manual Tire Bead Breaker 179• Excellent for working on tire without removing 8/27/2018 9:55:24 AM the wheel• Great for all kinds of tires - ATV, golf cart, truck, bus, agricultural and even back hoe tires• Operates with an air ratchet or manual wrench• Weight 12 lbs.#F - Tools & Equipment.indd 179

Mount / Demount Tools GAIBB6L GAIG12100 & GAIG12300 Tire Bead Seating Tool Demount Tools• Combines the unique rapid air • GAIG12100 - Demounts release technology and easiest- tire sizes 17.5” - 24.5” to-handle tank • GAIG12300 - Demounts• Smaller tank (6 liters) allows for super single tire sizes easier handling • Only a single tool needed to• Lightweight - 14 lbs. demount tires• Push-button trigger allows tech- • Eliminates the need to lift nician to keep both hands on the the tire and wheel tank • Unique design protects GAIBB6L valuable tire casings for retreading • Patent-pending handle design protects against dam- age to the tool GAIG12100 GAIG12300 M-100 Mount/Demount Tool • Effortless Truck Tire Mount M-100 and Demount • Superior Tool Quality • Time Saving • Max-Well Quality TSICH-5 KEN35440 Tire Bead Seating Tool Demount Tool • Easily seats the • Quickly demount nearly any 22.5” and 24.5” tubeless truck tire, up to a 13” wide toughest tire bead wheel saves time and • Ergonomic shaped steel handle with no-slip grip money • Allow tire demounting without lifting the • 6 gallon capacity wheel assembly with ASME certi- • Comes with 31810 Leather Rim Protector fied tank KEN35440 • Designed for commercial use TSICH-5 on large truck tires, auto and ATV tires180 • Weight: 27 lbs.#F - Tools & Equipment.indd 180 8/27/2018 9:55:25 AM

Mount / Demount Tools Lock Ring ToolsPart No. Description Length Stock Weight 11/16” (17.5mm) 2 1/4 lbs.Truck Lock Ring Remover 11/16” (17.5mm) 2 1/2 lbs. 11/16” (17.5mm) 2 1/2 lbs.KEN32123 Designed especially for Firestone 24” (61.0cm) 5/8” (16.0mm) 1 3/4 lbs. RH and TI rims 5/8” (16.0mm) 1 3/4 lbs.KEN33223 Designed especially for Firestone 30” (76.2cm) 5/8” (16.0cm) 1 3/4 lbs RH and TI rims 3/4” (19.0mm) 4 1/2 lbs.Combination Rim / Ring ToolKEN33224 Flat tapered end ideal for all round 23 1/2” (59.7cm) ring and rim work5º Rim Lock ToolKEN32125 For servicing 5º wide base rims 18” (45.7cm)Special Lock Ring Tool Long tapered curved end for R-1 18” (45.7cm)KEN32127 continuous side rings; short curved end for Goodyear rimsLock Ring ToolKEN32128 Removes continuous side ring on 18” (45.7cm) two-piece truck rimsHeavy Duty Lock Ring ToolKEN34648 Use for multi-piece wheels, espe- 37” (94.0cm) cially hub type KEN32123 KEN33223 KEN33224 KEN32125 KEN32127 KEN32128 181 KEN34648 8/27/2018 9:55:26 AM#F - Tools & Equipment.indd 181

Tire Spreaders 3050 3050RB 3050 RHS-300 Tire Spreader• This portable tire spreader performs passenger and light truck tire inspections with ease• The portable tire spreader fits over the center post of most tire changers (up to 1 ¾” post diameter)• Hand-operated spreading device allow easy access to any portion of the tire 3050RB Tire Spreader• The adjustable tire spreader can accommodate all tire from garden service through light truck• The tire spreader has a foot-control swivel, tilts and is equipped with a tool tray and a floor stand base-plate• Platform Height: 39 1/4” RHS-300 Deluxe Tire Spreader • Versatile machine with twice the lift height • Smaller dimensional footprint • Will handle tires 20% wider • 33% greater lifting capacity • Handles tires sizes from passenger, truck, tractor and small OTR • Tilt function for operator comfort • Lifting Capacity: 660 lbs • Lifting Height: 34.5” • Operating Pressure: 145 PSI • Weight: 507 lbs.182 8/27/2018 9:55:28 AM#F - Tools & Equipment.indd 182

Torque Tools• +/- 3% accuracy Torque Wrenches• Sealed pear head design• Twist locking collar allows easy setting of desired torque and prevents accidental change of torque setting while in use• One finger operated reversing lever for better productivity• Elastomer handle grip for comfort and oil resistance KTI-721171/4” Micrometer Torque Wrench, 30-150 in/lbs. KTI-72117 KTI-72140 KTI-721403/8” Micrometer Torque Wrench, 25-250 in/lbs. KTI-72143 KTI-721433/8” Micrometer Torque Wrench, 10-100 ft/lbs. KTI-72141 KTI-721411/2” Micrometer Torque Wrench, 20-150 ft/lbs. KTI-72142 KTI-72142 KTI-72145 1/2” Micrometer Torque Wrench, 30-250 ft/lbs. KTI-72145 3/4” Micrometer Torque Wrench, 100-600 ft/lbs. SUN2450 AMN67000 5 Piece Torque Extension Set Torqcheck - 1/2” Torque Wrench Tester• All come in a 1/2” drive: type 65 ft/lbs., 80 ft/lbs., 100 ft/lbs., 120 ft/lbs. and 140 • The most affordable way to accurately check ft/lbs. extension bars torque wrenches• Sizes are color coded • Guaranteed accurate within +/- 2% • For use with all 1/2” torque wrenches • Precision needle gauge measures from 0+180 ft. lbs. • Not to be used with impact wrenches AMN67000 SUN2450 183#F - Tools & Equipment.indd 183 8/27/2018 9:55:29 AM

Torque Tools & Shop Service Tools Torque Sticks Part No. Color Drive Size FT/LBS. Part No. Color Drive Size FT/LBS.ACC-10-0304 Green ½” 17mm 55 33mm 30mm 330ACC-10-0305 Red ½” 17mm 80 ACC-20-3045 Unpainted 33mm 33mm 160ACC-10-0306 Yellow ½” 19mm 65 33mm 33mm 140ACC-10-0307 Blue ½” 19mm 80 ACC-20-3345 Unpainted 22mm 140ACC-10-0308 Gray ½” 19mm 100 ½” 24mm 140ACC-10-0309 Black ½” 21mm 60 ACC-20-3360 Unpainted ½” 140ACC-10-0310 Light Brown ½” 21mm 80 ½” 1” 140ACC-10-0311 Brown ½” 21mm 100 ACC-10-3898 Light Purple ½” 1-1/16” 140ACC-10-0312 White ½” 22mm 120 ½” 140ACC-10-0313 Turquoise ½” 140 ACC-10-3899 Light Green ½” 1⅛” 175ACC-10-0327 Light Blue ½” ⅞” 100 ¾” 1¼” 250ACC-10-0328 Charcoal ½” 22mm 147 ACC-20-3900 Purple 1” 1¼” 475ACC-10-0329 Off White ½” 21mm 90 1” 1¼” 475ACC-10-0334 Light Yellow ½” 17mm 113 ACC-20-3901 Tan 1” 33mm 475ACC-10-0336 Orange ½” 17mm 75 1” 1½” 250ACC-10-0337 Dark Green ½” 22mm 60 ACC-20-3902 Olive ¾” 13/16 sq 475ACC-10-0340 Mud ½” 22mm 80 ¾” 1¼” 475ACC-10-0341 Quartz ½” 14mm 120 ACC-20-3903 Burgundy ¾” 33mm 475ACC-10-0342 Light Tan ½” 19mm 90 ¾” 1½” 400ACC-10-0343 Red-Orange ½” 19mm 110 ACC-20-3904 Orange 41mm 13/16” 21mm 41mm ACC-20-3908 Red ACC-20-3909 Brown ACC-20-3910 Black ACC-20-3911 Yellow ACC-20-3918 Red ACC-20-3919 Brown ACC-20-3920 Black ACC-20-3921 Yellow ACC-20-4155 Unpainted Wheel Cover Puller / Replacer Part No. Description Length Stock Weight KEN31568 Standard 14” (36cm) 7/16” (11.1mm) 1 1/4 lbs. KEN31568 AMN67300 Nut Buddy AMN67300 • Bust loose the most stubborn wheel nuts • Use on commercial or agricultural wheels • Gear ratio - 58:1 • Rated output torque: 2,950 ft/lbs. • Two sockets included: 1½” (38mm) and 1-5/16” (33mm)184#F - Tools & Equipment.indd 184 8/27/2018 9:55:31 AM

Shop Service Tools Tire Wrenches Part No. Description Socket Sizes Length Stock WeightStandard Professional 5/8” (16mm) 4 1/2 lbs. 3/4”, 13/16”, 7/8”, 22” (55.9cm) 3/4” (19mm) 6 1/2 lbs. KEN35659 Passenger 15/16” 25” (63.5cm) 5/8” (16mm) 4 3/4 lbs. KEN35690 Light Truck 7/8”, 15/16”, 1”,Professional Gold 4-Way 11/16” 1” (25mm) 13 3/4 lbs. 1” (25mm) 13 1/2 lbs KEN35657 Passenger 3/4”, 13/16”, 7/8”, 23” (58.4cm)Heavy Duty Truck 4-Way 15/16” KEN35695 Truck 1 1/16”, 1 1/4”, 1 1/2”, 27 1/2” (69.9cm) 13/16” sq. 27 1/2” (69.9cm) KEN35697 Truck 1/4”, 1 1/2”, 13/16”,Bud Nut Wrenches 3/4” KEN30609 SAE & Metric KEN30610 Metric service arm KEN30612 Metric 1 1/2” (38mm) 35mm 41mm KEN35659 KEN35697 KEN30609 Tire Hammers KEN35323Part No. Length Head Weight WeightWood Handled HammersKEN35323 16 1/2” (41.93cm) 5 1/2 lbs 6 1/2 lbs.Fiberglass Handled HammersKEN35423 18” (45.7cm) 4 3/4” (16mm) 7 lbs. AMN37200 AMN37200 Hub Stud Cleaner Kit 185• Designed to be used with either 3/8” or 1/2” drill, 1/2” impact wrench or low-speed tire buffer• Removes rust, corrosion and other build-up from wheel stud, drums and tire rim• Helps proper torque of lug nuts by removing corrosion• A must for easy/accurate tire balancing• Kit includes two tools and 10 replacement discs (2” Large Pads 5 each) (1.5” Small Pads 5 each)#F - Tools & Equipment.indd 185 8/27/2018 9:55:32 AM

Air Pressure & Tread Depth Gauges Part No. Air Pressure Gauges 179 Description Straight truck pressure gauge: 20-150 PSI, calibrated in 2 pound increments 181 Truck pressure gauge: 20-120 PSI, calibrated in 2 pound increments, high impact chrome body 182 Agricultural pressure gauge: 5-50 PSI for air / liquid ballast filled tires 183 Dual head truck pressure gauge: 10-120 PSI, calibrated in 2 pound increments, chrome body 184 Dual head pocket truck pressure gauge: 20-120 PSI, calibrated in 2 pound increments 5900 Digital pressure gauge: 5-100 PSI, LCD reading and automatic shut-off 17-908C Air / liquid tires pressure gauge: 5-45 PSI 17-911C High pressure pocket gauge: 20-120 PSI17-1317BC Premium dual foot gauge: 20-120 PSI, straight-on 17-1045C Straight-on, 2 sided nylon bar: 10-150 PSIH300532P Digital Tire Inflation Gauge, 0-175 PSI, 6 ft. durable hose, measures PSI, BAR & kPaH310532P Analog Tire Inflation Gauge, 0-175 PSI, 6 ft. durable hose, measures PSI, BAR & kPa Part No. Tread Depth Gauge 185 Description Tread Depth Gauge: reads 0” to 1” in 1/32 increments 5800 Digital Tread Depth Gauge: reads in mm, inches and fractions, LCD display, 1/32 increments and has a zero function 17-607 Tread Depth Gauge: 1/32 and mm increments 17-607C Tread Depth Gauge: color coded, 1/32 and mm increments 17-697 OTR Tread Depth Gauge 5800 5900 17-607C 17-607 H300532P H310532P 17-1317B 17-911 183 182 17-908 185 184186 17-1045C 181 179#F - Tools & Equipment.indd 186 8/27/2018 9:55:35 AM

Bottle Jacks KTI-63212 12 Ton Capacity Bottle Jack Part No. Description Minimum Maximum Height Height KTI-63212 12 Ton Bottle Jack 9-1/16” 18-5/16” • Powerful jack makes big loads easy to lift KTI-63212 • Carrying handle for easy handling • Two piece slip fit handle for controlling the release valve and pumping the jack SUN4912CAH2 12 Ton Air Bottle Jack Part No. Description Minimum Maximum Height Height SUN4912CAH2 12 Ton Bottle Jack 9.9” 18.5” • Designed for operating either manually or pneumatically • Double spring return • Airhose can swivel in any direction • Minimum air pressure required is 90 PSI SUN4913A SUN4912CAH2 SUN4913A 12 Ton Capacity Short Bottle Jack Part No. Description Minimum Maximum Height HeightSUN4913A 12 Ton Bottle Jack 6” 10.5”• Ductile iron base for added strength• Hydraulic bypass prevents over-travel of ram• Three piece slip fit handle for controlling the release valve and pumping the jack 432020 432020 187 20 Ton Air/Manual Bottle Jack Part No. Description Length Width 432020 20 Ton Bottle Jack 5.12” 8.66” • Chrome plated ram and aluminum air motor guarantee optimal performance • Premium air filter connected to hose#F - Tools & Equipment.indd 187 8/27/2018 9:55:36 AM

Bottle Jacks 412000 20 Ton Hydraulic Bottle JackPart No. Description Hyrdaulic Extension Stock Screw412000 20 Ton Bottle Jack 6.30” 3.15”• Has a chrome main ram and a chrome pump piston• The extension screws have a pressed thread KTI-63220 412000 20 Ton Capacity Bottle Jack KTI-63220 OTC4321CPart No. Description Minimum Maximum Height Height 8/27/2018 9:55:36 AMKTI-63220 20 Ton Bottle Jack 9-3/4” 14-3/8”• Includes an overload valve to prevent being usedbeyond its rated capacity• Ductile iron base for added strength• Electrostatic paint for rust prevention• Hydraulic bypass prevents over-travel ram• Two piece slip fit handle for controlling the releasevalve and pumping the jack OTC4321C 20 Ton Air Assist Hydraulic Bottle JackPart No. Description Minimum Maximum Height HeightOTC4321C 20 Ton Bottle Jack 9 7/16” 17 11/16”• Oil bypass system prevents the lifting ram from being over extended188#F - Tools & Equipment.indd 188

Service Jacks 420300 3 Ton Garage Jack Part No. Description Length Width 420300 3 Ton Garage Jack 31.30” 15.15” • Equipped with a rubber saddle and handle bumper, universal joint release valve results in precise and safe operation while under-load • Pump pistons are angled and protected from contamination 420300 420302 resulting in smooth, full pumping stroke KTI-63156 420302 KTI-63185 3 Ton Garage Jack 189 Part No. Description Length Width 420302 3 Ton Garage Jack 28” 14.15” • Professional universal joint release valve makes it possible to lower the jack with load very precisely and free of any risks • The “protected” pump piston is placed at a 45º angle so a complete pumping stroke will always be utilized KTI-63156 5 Ton Hydraulic Floor Service JackPart No. Description Lifting Saddle Range DiameterKTI-63156 5 Ton Service Jack 6½ - 22¼” 6½• Professional series turbo lift service jack boasts long, com- pact structure design, extra heavy duty welded steel chassis and universal joint release valve• Patented built-in bypass device prevents over-pumping damage KTI-63185 10 Ton Hydraulic Service Jack Part No. Description Lifting Saddle Range DiameterKTI-63185 10 Ton Service Jack 6¼ - 22 ⅛” 6⅜”• Service jack features extra wide 2” front wheels, long, low design with additional foot pedal, and spring-loaded T- handle that can be set at any angle#F - Tools & Equipment.indd 189 8/27/2018 9:55:37 AM

Service Jacks 432001 20 Ton Air Service Trolley Jack Part No. Description Hyrdaulic Extension Stock Screw 432001 432001 20 Ton Service Jack 4.25” 3.15” • This heavy duty model is designed for service jobs in the truck industry • This jack has an extension screw and 3 saddles that can be placed on top of each other for added height 432003 20 Ton Air / Hydraulic Jack with Cart Part No. Description Hyrdaulic Extension Stock Screw 432003 20 Ton Service Jack 5.7” 3.15” • These bottle jacks are fixed on a heavy duty cart, which results in convenient transportation and easy reach of lifting point • Due to the smart cart frame, these jacks can be stored vertically 432003 ASTAJ22FE2A 22 Ton Air Over Jack with Quick Springs • Large 8” (203mm) diameter hard rubber tires make ma- neuverability easier • Includes quick springs for fast ram retraction - eliminates manual lowering of jack, comes with extended height saddle adapters • Safety overload system prevents jack from being used beyond its rated capacity190 ASTAJ22FE2A#F - Tools & Equipment.indd 190 8/27/2018 9:55:37 AM

Hydraulic Oil & Wheel Dollies HJ032 Hydraulic Jack Oil • 32 oz. of rust inhibitors, anti-wear and anti-foam agents • For use in most style hydraulic jacks HJ032 OTC5096A OTC5096A Easy Lever ™ Wheel Dolly for Wide Tires• Heavy duty contruction capable of toting 300 pounds• Dolly handles tire diameters of 36” to 48”• Onboard rollers make stud-to-hole alignment a snap• Features improved “bent-arm” design to improve leverage and minimize back strain• Spring loaded kickstand for handy parking• Rugged tubular steel construction OTC1769A OTC1769A Truck Dual Wheel Dolly • This 1,500 pound capacity dolly will remove, transport and replace dual wheel and tire assemblies without strain or struggle • Swivel casters, 3 1/2” front and 3” rear, provide easy maneuverability • Floor space is 43” x 42” • The hydraulic jack provides over 6 1/2” of lift and tilts wheel assembly 7º to prevent damage to wheel seal • Includes a 6’ support chain to hold load in place 191#F - Tools & Equipment.indd 191 8/27/2018 9:55:38 AM

Tire Changers 8006330 COATS® CHD-6330 Heavy Duty Tire Changer • Four-jaw chuck allows fast and easy clamping of virtually all rim styles, including demountable, reverse disc, standard disc and off-road-style wheels • Floating jaws match wheel contours for excellent grip and safety • Solid, single-piece fram for added capacity and reliability • Portable wired control unit lets you work from the best angle at all times • Handles Rim Diameter 13” - 27” • Maximum Tire Diameter 63” • Maximum Tire Width 30.5” • 220V, 3 Phase COATS® Tire Changer Accessories for 50, 60 & 70 Series Part No. Description 8183061 Nylon Mount Demount Head 8184432 High Spoke Mount Demount Head 8182963 Nylon Inserts - package of 12, tire changers with metal mount demount head 8183061 8184432 8182963192 8/27/2018 9:55:43 AM#F - Tools & Equipment.indd 192

Tire Changers80070XEH3 193COATS® 70XEH3 Tire Changer• Best-in-class clamping capacity comes standard with 6” 2 24” external (8” - 26”internal) (car & light truck only)• Service the widest array of applications without secondary adapter• Advanced clamp positioning allows for greater control when clamping wheels• Position clamps exactly where needed at any point between fully in and fully out• No need to wait for the clamps to have to cycle the full range• Hybrid duckhead• Robo-Arm® power assist helper arm and single point bead blast• Electric or air tabletop motor and hand or foot bead loosener control 85609950 COATS® RC-55 Tire Changer • External rim clamping range from 10” - 24” diameter • Maximum rim width 10.5” • Maximum tire diameter 50” • Robo-Arm® power assist helper arm • Designed for alloy and steel wheels • Electric or air motor turntable available • Includes bead sealing jet to aid inflation85609949COATS® RC-45 Tire Changer• External rim clamping range from 10” - 24” diameter• Maximum rim width 10.5”• Maximum tire diameter 50”• Designed for alloy and steel wheels• Electric or air motor turntable available• Includes bead sealing jet to aid inflation 85002500 BaseLine™ BL500 Tire Changer • External clamping: 10” - 24” • Internal clamping: 12” - 26” • Maximum tire diameter: 38” • Maximum rim width: 10” • Robo-Arm® power assist helper arm • Includes bead sealing jets to aid in inflation • Electrical power requirement: 110 volt • Air requirement: 125 psi#F - Tools & Equipment.indd 193 8/27/2018 9:55:47 AM

Tire Changers 85002300 BaseLine™ BL300 Tire Changer • External clamping: 10” - 24” • Internal clamping: 12” - 26” • Maximum tire diameter: 38” • Maximum rim width: 10” • Includes bead sealing jets to aid in inflation • Electrical power requirement: 110 volt • Air requirement: 125 psi ATEATTC289 Atlas TC289 • External rim clamping range: 117/8” - 28” • Maximum rim width 18.5” • Maximum tire diameter: 47.5” • Designed for alloy, aluminum and steel wheels • Tilt back wheel clamp tire changer • Included bead blaster ATETC229-WB11 8/27/2018 9:55:49 AM Atlas TC229 Tire Changer & WB11 Wheel balancer combo • External clamping: 10” - 24” • Internal clamping: 12” - 26” • Maximum tire diameter: 38” • Maximum rim width: 10” • Includes bead sealing jets to aid in inflation • Electrical power requirement: 110 volt • Air requirement: 125 psi194#F - Tools & Equipment.indd 194

850645002 Wheel BalancersCOATS® 6450-2D Heavy Duty Wheel Balancer 85001300• 1-1/2 HP direct drive motor• Dual Calibration software COATS® 1100 Wheel Balancer• Maximum tire diameter 52’ • 1-1/2 HP direct drive motor• Maximum rim width 20” • Maximum tire diameter 44”• Maximum tire weight 500 lbs. • Maximum rim width 30”• 4 center cones included 2.44” - 6.95” • Maximum tire weight 150 lbs.• 220 volt • 40mm shaft diameter• Optional wheel lift and adapters available • Direct tape-a-weight measurement • Static on screen • Includes four centering cones • 220 volt 80016003D COATS® V200-3D Wheel Balancer • 1-1/2 HP direct drive motor • ProBalance technology • Auto stop-n-lock weight placement • Maximum tire diameter 44’’ • Maximum rim width 30” • Auto hood start • Behind-the-spoke mode • Automatic distance, diameter and rim width data entry • Laser guided tape-a-weight placement • 220 volt, 1PH or 220 volt, 3PH • Adapter kit purchase required#F - Tools & Equipment.indd 195 195 8/27/2018 9:55:53 AM

Wheel BalancersATEATWB49Computer Wheel Balancer• Rim sizes 10” - 32”• Max. wheel weight: 150 lbs• 110 V / 1-phase• Display in standard or metric units• Self-diagnosis/self-calibrationATEATWBT-210Atlas WBT210• Maximum tire diameter 47”• Maximum wheel width 20”• Maximum tire weight 440obs.• 40mm shaft diameter• 220 volt 1 ph• Pneumatic wheel lift• Automatic brake, start and stop• Self-diagnosis / self-calibration Part No. COATS® Wheel Balancer Accessories 8113277C Description Light Truck Cone Kit - double-sided cone 4.88” - 6.88” & backing 8112421 plate, 40mm 8111935 Short Cone - 2.65” - 3.025”, 40mm Faceplate Extension Spacer - fits Coats Direct Drive Balancers196 8113277C 8112421 8111935#F - Tools & Equipment.indd 196 8/27/2018 9:55:56 AM