PartsLOCTITE SF 7063 LOCTITE SF 7200 LOCTITE SF 7840 Prior to Bonding Gasket Remover General Cleaner Solvent Solvent Water• For use prior to bonding • Remove old gaskets • Biodegradable and sealing applications • Minimal scraping • Can be diluted with water• Leaves no residue• For similar performance and improved health & safety select LOCTITE SF 7064 | 51
Cleaners – Parts and Hands CleanersHow to apply LOCTITE SF 7850Application• Rub into dry hands until dirt or grease is dissolved• Wipe hands dry or rinse with water• Repeat procedure if necessaryHow to apply LOCTITE SF 7063Application• Treat surfaces to be cleaned by generously spraying with LOCTITE SF 7063• Wipe surface when still wet with a clean paper towel• Repeat if necessary until contamination is removed• Allow solvent to evaporate until surface is completely dryNote:LOCTITE SF 7063 can cause stress cracks on sensitive plastics.52 |
How to apply LOCTITE SF 7200Application• Before applying protect painted surfaces as LOCTITE SF 7200 may attack the paint• Spray a heavy coat onto flange or surface. Wait 10 – 15 min for the gasket to soften (for silicone gaskets 30 min)• Remove gasket with soft scraper and wipe flange clean• Repeat procedure if necessaryHow to apply LOCTITE SF 7840Application• Dilute LOCTITE SF 7840 with water• Soak or spray parts and wipe or rinse cleanHint:Effectiveness can be enhanced by diluting with warm waterFor detailed information please refer to the Technical Datasheet or contact your Henkel Technical Service Team. | 53
Lubricants and GreasesWhat type of lubricant do you require? General Spray Lubricant Solution LOCTITE LB 8201 LOCTITE LB 8021 General purpose Silicone oilBase Mineral oil Silicone oilViscosity 17,5 cSt (+50 °C) 350 mPa·sService temperature range -20 to +120(°C) – -30 to +150Approvals H1 NSFComments • Multi-purpose oil • Silicone oil • Frees assemblies • Lubricates metal and • Lubricates metal • Cleans parts non-metal surfaces • Displaces moisture • Suitable as release agent • Prevents corrosionTechnology Benefits• Protect moving parts against friction, wear and corrosion• Prevent overheating54 |
Specialized Lubricant Dry LubricantLOCTITE LB 8018 LOCTITE LB 8011 LOCTITE LB 8191 Solvo Rust High temperature chain oil General purposeMineral oil Silicone oil MoS2< 100 mPa·s 11,5 cSt (+20 °C) 11 s (cup 4)N.A. -20 to +250 -40 to +340– H2 NSF –• Transparent penetrating • High temperature chain • Quick drying oil in an aerosol can to oil spray • Surface protection free rusted or seized nuts, bolts, screws, fit- • Oxidation resistance against corrosion tings and other fasteners prolongs lubricant ser- • Enhances the as well as metal com- vice life ponents performance of oils and • Lubricates open mecha- greases• Prevents rust nisms, conveyors and• Recommended for clean- chains at elevated tem- peratures up to 250 °C ing before lubricatio | 55
Lubricants and GreasesWhat type of grease do you require? General Solution LOCTITE LB 8105 General purposeBase Mineral oilViscosity –Service temperature range (°C)Approvals -20 to +150Comments H1 NSF • Mineral grease • Lubricates moving parts • Colourless • Odourless • Ideal for bearings, cams, valves and conveyorsTechnology Benefits• Protect moving parts against friction, wear and corrosion• Prevent overheating56 |
SpecializedLOCTITE LB 8104 LOCTITE LB 8102 LOCTITE LB 8101Silicone grease High temperature resistance Chains, gears Silicone oil with Mineral oil, extreme Mineral oil, E.P.inorganic thickenr p ressure additives–––-40 to +200 -30 to +200 -30 to +170H1 NSF – –• Silicone grease • High temperature grease • Adhesive grease for open• Valve and packing grease • For humid conditions mechanical systems• Wide temperature range • Ideal for rolling/plain • Protecs against water up to +200°C bearings, open gears and ingress• Lubricates most plastic slideways • Excelent wear and high and elastomeric com- presure resistance ponents• NLGI Class 2/3 • Lubricates chains, open gears and worm screws • NLGI Class 2 | 57
Lubricants and GreasesHow to apply1. Preparation Cleaning • It is recommended to use LOCTITE SF 7063 to degrease and clean surfaces • Surfaces should be free from scale, oxides and lubricant residues2. Application Shake well before use.A LOCTITE LB 8105, LB 8102 • Check compatibility with other grease residues • Apply to clean parts by brush, spatula or grease gun Hint: Product may be suitable for use in automatic application systems.B LOCTITE LB 8021, LB 8201 • Choose between jet and spray (based on application needs) • Spray consistently onto parts to give a uniform film58 |
C LOCTITE LB 8191 • Product should be sprayed on cleaned parts from a distance of about 20 cm to give a uniform coating • Let parts dry for 15 to 30 min at ambient temperatureFor detailed information please refer to the Technical Datasheet or contact your Henkel Technical Service Team. | 59
Anti-Seize General purposeWhat type of Anti-Seize do you require? LOCTITE LB 8150/8151 Solution AluminiumColour GreySolid lubricating agent Aluminium, graphite, extreme pressure additivesService temperature range (°C)Approvals -30 to +900Comments – • General purpose aluminium assembly pasteTechnology Benefits• Protect parts against corrosion, galling, seizing and fretting• Resistant to high temperatures, corrosive environments and high loads• Prevent overheating60 |
High performance LOCTITE LB LOCTITE LB LOCTITE LB8007/8008/8065 8009 8023 Copper Heavy duty MarineCopper Black BlackCopper, graphite Graphite, calcium fluoride Graphite, calcium, boron nitrate, rust inhibitors -30 to +980 -30 to +1.315 -30 to +1.315 – – ABS• General purpose copper assembly paste • Metal-free • Protection against fresh • Excellent lubricity and salt water • Superior protection • Outstanding water wash- for stainless steel and out resistance titanium • Metal-free • Excellent lubricity | 61
Anti-SeizeHow to apply1. Preparation Cleaning • It is recommended to use LOCTITE SF 7063 to degrease and clean surfaces • Surfaces should be free from scale, oxides and l ubricant residues2. Application Shake well before use.A Can / brush top • Apply a thin layer over the whole surface by brushing evenly over the whole surface • Do not dilute • Assemble in accordance to manufacturer’s recommendationsB Spray can • Spray consistently onto parts to give a uniform film • Do not dilute • Assemble in accordance to manufacturer’s recommendations62 |
For detailed information please refer to the Technical Datasheet or contact your Henkel Technical Service Team. | 63
Surface Treatment and RustWhat kind of treatment do you require? Rust treatment Solution LOCTITE SF 7500 Rust ConverterColour Matt blackService temperature range (°C)Comments – • Convert rust into a s table base • Cured product acts as primer ready for paintingTechnology Benefits• Solutions for all types of surface treatments or preparations64 |
P revention ProductsCorrosion protection Protection of welding Tamper proofing equipmentLOCTITE SF 7800 LOCTITE SF 7900 LOCTITE SF 7414 Zinc Spray Ceramic Shield Movement Detector Grey White Blue -50 to +550 – -35 to +145• Excellent cathodic • Prevent adhesion of • Visually detect m ovement c orrosion protection on welding spatter of parts ferrous metal • Long-term protection of • For outdoor applications• Restore protection to welding equipment galvanised parts • Silicone-free | 65
Surface Treatment and RustHow to apply LOCTITE SF 75001. Preparation Use a wire brush to remove flaky rust and loose scale. It is recommended to use LOCTITE SF 7063 to remove oil, grease and dirt. Shake well before use.2. Application Brush or sponge on liberally. Apply two coats (recoat time: 60 to 120 minutes). Uneven colour indicates need for additional coats. Allow minimum 24 hours to dry before painting. Hint: Do not apply in direct sunlight or on wet surfaces.How to apply LOCTITE SF 78001. Preparation Remove rust, old coats of paint etc. from surface. Gritblast surface if possible. It is recommended to use LOCTITE SF 7063 to finally remove oil, grease and dust. Shake well before use.2. Application • Spray onto clean parts from 20 to 30 cm to give a uniform film • The coating becomes dry to touch after 30 to 60 minutes. Allow 24 hours to dry completely66 |
P revention ProductsHow to apply LOCTITE SF 7900 Ceramic Shield1. Preparation Clean contact tip and shroud from adhering spatter. For best results, use a new contact tip and shroud. Shake well before use.2. Application 1 2 • Place the contact tip on the welding torch and apply from a distance of 10 – 15 cm. Fit the shroud to the welding torch and coat the exterior and interior. Let the coating dry for several seconds • After the application reverse the can and spray for several seconds to prevent clogging of the nozzleHow to apply LOCTITE SF 74141. Preparation It is recommended to use LOCTITE SF 7063 to degrease, clean and dry surfaces.2. Application Squeeze the tube to extrude the paste and form a narrow bead across the parts. Let product dry for 60 seconds.For detailed information please refer to the Technical Datasheet or contact your Henkel Technical Service Team. | 67
Emergency Repair ProductsWhat is your application? O-Ring Free corroded Detect pipe leaks replacement parts Solution LOCTITE LOCTITE LOCTITE O-RING KIT LB 8040 SF 7100 O-Ring Kit Freeze & Release Leak DetectorService – – +10 to +50temperature range(°C) • Set with rub- • Shock freezing • ProducesComments ber cords, (-40 °C) b ubbles at point L OCTITE 406 of leakage and tools to cre- • Release ate customized rusted, c orroded • For all gases and O-rings and seized gas mixtures c omponents except for oxygen • Eliminates the need for an • Wicks directly • Non-toxic / non- inventory of into the rust by flammable different sized capillary action O-Rings • Use for iron, copper and plastic piping68 |
Seal pipe leaks Taping LOCTITE LOCTITE LOCTITE TEROSON EA 3463 PC 5070 SI 5075 VR 5080Metal Magic Steel™ Pipe Repair Kit Insulating and High Strength Tape Stick Sealing Wrap-30 to +120 – -54 to +260 up to +70• Steel-filled • Easy-to-use • Insulating and • Fabric reinforced kneadable stick repair kit for Sealing Wrap tape temporary repair• For emergency of weak areas on • Withstand • Easy to tear by repair of tanks, pipes extreme hand pipes and conditions castings • Repair, reinforce, • Stretches fix, seal and 3-times protect its size • Available in red and black | 69
Emergency Repair ProductsHow to apply LOCTITE LB 80401. Preparation Remove loose dirt and rust. Shake well before use.2. Application • Spray onto parts from a distance of 10 – 15 cm for 5 to 10 seconds • After 1 to 2 minutes disassemble parts. If necessary repeat procedure5 – 10 sec. -43 °C Active ingredientminimum Corrosion layerHow to apply LOCTITE PC 50701. Preparation • Turn off pressure in pipe system • Thoroughly clean and abrade surfaces. Finally clean with LOCTITE SF 70632. Application • Mix required amount of LOCTITE EA 3463 (details see chapter Metal-filled Compounds). Firmly press product into the crack, hole or void • Activate tape by soaking into water at room temperature for 20 seconds. Wrap tape tightly around repair, building up at least 4 layers70 |
How to apply LOCTITE O-Ring KIT1. Preparation • Clean cutting blade using LOCTITE SF 7063 • Cut the required approximate length of cord. Use the O-Ring cutting fixture to cut at both ends to achieve clean bonding surfaces at required length2. Application • Apply a small drop of LOCTITE 406 to one end of the O-Ring • Immediately join the two ends using the V-groove on the end of the cutting fixture. Hold in place for 30 seconds, then O-Ring is ready for serviceHow to apply LOCTITE SF 71001. Preparation Shake well before use.2. Application • Spray product from 15 to 20 cm onto suspect area • A leak will be clearly visible, as the product will start foaming at the leaking areaFor detailed information please refer to the Technical Datasheet or contact your Henkel Technical Service Team. | 71
Equipment – DispensersManual applicatorsIDH number For product For pack sizeIDH 142240 • LOCTITE 518, 510, 577, • 300 ml 660, SI 5331, SI 5366, • 310 ml SI 5980, SI 5990, SI 5616 • 250 ml (1:1) • 265 ml (2:1) • TEROSON MS 930, MS 9320 SF, PU 6700 • TEROSON MS 9399 • 50 ml (1:1)IDH 150035 • LOCTITE EA 9466 • 50 ml (1:1, 2:1)IDH 267452 • TEROSON PU 6700IDH 363544 • LOCTITE 518, 510, • 50 ml SI 5980, SI 5990 • LOCTITE AA 3038 • 50 ml (10:1)IDH 103402672 |
Peristaltic dispensersIDH number For product For pack size • LOCTITE 222, 243, 290, • 50 ml 270, 542, 603, 638, AA 326IDH 608966 • LOCTITE 222, 243, 290, • 250 ml 270, 542, 603, 638IDH 88631Pneumatic applicatorsIDH number For product For pack size • LOCTITE PC 7255 • 900 mlIDH 1175530 | 73
Equipment – AccessoriesMixersIDH number For product For pack size • TEROSON PU 6700 • 250 ml (1:1)IDH 780805 • LOCTITE 3090 • 10 ml (10:1)IDH 1453183 • LOCTITE EA 9466 • 400 ml (2:1)IDH 1487439 • LOCTITE EA 9466 • 50 ml (1:1; 2:1)IDH 1487440 • TEROSON PU 6700, MS 939974 |
Nozzles For product For pack size • TEROSON MS 930 • 310 ml IDH number • LOCTITE SI 5331, • 310 ml IDH 581582 SI 5366, SI 5980, SI 5990 IDH 1118785 For product For pack size • Suitable for all liquid • 18 (= Green)Needles instant adhesives ID 0,84 mm IDH number • Suitable for all liquid • 20 (= Pink) IDH 88661 instant adhesives ID 0,61 mm IDH 88662 | 75
Maintenance Expert TrainingHigh-quality products can be only as good as the people who use them.That is why we offer hands-on training on the use of our products inmaintenance and repair environments.Our trainers are thoroughly familiar with the day-to-day problems youmay encounter and will give you the tools and practical know-how forsuccessful application of our products.The training content is based on the product categories of thisM aintenance Expert Guide and can be tailored to your needs.Features• Pre-plant survey• Hands-on training• Conducted on site• Training materials supplied• Review of common failure causes and prevention• In-plant follow up76 |
Your benefitsThe training will provide you with knowledge and tools to do thef ollowing: Increase Reliability and avoid downtime of your industrial equipment and machinery by regular maintenance Improve Safety at work by increasing reliability of your machinery and by using non- hazardous products Save Time by using innovative technologies that reduce downtimes and increase s ervice intervals Reduce Costs by repairing worn or damaged parts instead of replacing themContact your Henkel Engineer for more details and to arrangetraining for your maintenance and repair team. | 77
Specific Maintenance SolutionsIndustry expertise and equipment know-howYears of experience in manufacturing and maintenance have enabled usto build up profound knowledge of the typical maintenance and repairtasks in all major industries and common industrial equipment.Industry programsOur industry programs cover the typical maintenance and repairc hallenges in your industry. They include numerous applicatione xamples, references and case studies. Learn how your specific repairtask was solved in a comparable situation.Power Mining Oil & GasMarine Railway Steel Plants78 |
Device programsOur device programs go even deeper into the specific m aintenanceand repair tasks of the industrial component. They include specifica pplication solutions for any repair task and suitable products uggestions. We will bring the solution so you can concentrate on yourbusiness. Pump Shaft CentrifugeLOCTITE SF 7063 LOCTITE SI 5980LOCTITE EA 3478 LOCTITE 243 LOCTITE LB 8150 LOCTITE 603 Gear BoxFind more information on the programs on www.loctite.co.uk/maintenance and c ontactyour Henkel Engineer for a workshop tailored to your needs. | 79
Find the right product and discover additional features. Check out our mobile Maintenance Expert Guide: m.loctite-repairs.co.uk Henkel AG & Co. KGaA Henkel & Cie. AG Gutenbergstr. 3 Salinenstr. 61 85748 Garching CH-4133 Pratteln Tel.: (+49) 89 9268-0 Tel.: (+41) 61 825 70 00 Fax: (+49) 89 910 1978 Fax: (+41) 61 825 73 03 www.loctite.de/instandhaltung www.loctite.ch/instandhaltungIDH Nr. ???????????? Henkel Central Eastern Europe The data contained herein are intended GmbH as reference only. Please contact Henkel Erdbergstraße 29 Technical Support Group for assistance and A-1030 Wien recommendation on specifications for these Tel.: (+43) 1 711 04 0 products. Fax: (+43) 1 711 04 4194 www.loctite.at/instandhaltung ® designates a trademark of Henkel and/or its affiliates in the US, Germany, and elsewhere © Henkel AG & Co. KGaA, 2016
Search
