CAF-Installation-Guide-PageFlip2022

Location Replacement Time Drivers Side Rear 5 Minutes Cargo Area. Tools Required: None Note: Battery Pack Ventilation Filter Applications 2010-2005 Ford Escape (Battery Filter) 2010-2010 Maz da Tribute (Battery Filter) 2010-2006 Merc ury Mariner (Battery Filter) New July-09 \"Instructions are provided as proper removal and installati CAF2062 for additional information.\"

The cover for the Battery Pack Ventilation Filter is on the drivers side in the rear cargo area. Use your fingers to pop off the plastic cover panel. 1 Locate the little black plastic cover that is held in place by two clips. Push the tabs to release this cover With the filter now visible, remove by pulling it directly out. Replace the filter ensuring the correct air flow direction. Reverse procedure to complete installation. 2 s general guidelines and may not provide every necessary detail for ion. Please consult your specific vehicle's owner's or repair manual ©2009 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 5 Minutes Tools Required: Flathead Screwdriver Applications Accent (Early ‘08) 2008-2006 Hyundai \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" Revised April-11 CAF2063

Left Tab Stops Right Tab 1 Open glove box. Remove the clips holding the glove box stops from both the left and right side. Tip: Pull each clip back (toward the rear of the car) and at the same time, pull them out (toward the center of the glove box). Lower the glove box completely. 2 With glove box lowered locate the filter housing cover. Remove access cover by pinching on the end tabs. Be sure to note the air flow direction. Remove the cabin air filter from the 3 filter housing. Replace cabin air filter, ensuring the filter is placed in the proper direction. Reverse procedure to complete 4 installation. ©2011 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Right Tab Sto Behind glove box 5 Minutes Tools Required: Flathead screwdriver Applications Accent (Late '08) Elantra (exc. Touring) 2011-2008 Hyundai 2013-2007 Hyundai \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" Apps. Updated Feb-13 CAF2064

op Right Tab Open glove box. Remove the clip on the right 1 holding the glove box stop. Tip: Pull the clip back (toward the rear of the car) and at the same time, pull it out (toward the center of the glove box). Lower the glove box completely. 2 With glove box lowered locate the filter housing cover. Remove access cover by pinching on the end tabs. Be sure to note the air flow direction. Remove the cabin air filter from the 3 filter housing. Replace cabin air filter, ensuring the filter is placed in the proper direction. Reverse procedure to complete 4 installation. ©2011 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Passenger side under 5 Minutes hood and cowl. Tools Required Flathead Screwdriver Applications 2009-2008 Pontiac G8 \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2065

Open the hood. Locate the six push pins holding the cowl cover in place. Remove the six push pins from the cowl cover. 1 See 2a, 2b and 2c for reference. 2a 2b 2c Remove cowl cover by pulling it up and away. With the filter now visible, remove the cabin air filter by grabbing at a corner and pulling gently. Replace the cabin air filter ensuring the correct air flow direction. Reverse procedure to complete installation. 3 ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 10 Minutes Tools Required: None Applications Lower glove box com pushing both sides inw 2009-2004 Kia Amanti Note: The cabin air filter \"Instructions are provided as general guidelines the lower portion of the b and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2067

1a Open the glove box. Disengage the damper strap. 1b 2 3 mpletely by Locate the filter cover. ward. Remove cover by pressing the clips at each side of the cover. (See inset image) Cabin Remove and replace cabin air Air Filter filter, ensuring the filter is placed in the proper direction. Reverse procedure to complete installation. r is located in 4 blower fan. ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 5 Minutes Tools Required: Open glove box. Flathead screwdriver Applications Lower completely by di the damper strap. 2010-2007 Hy undai V erac ruz \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2068

Stops 12 Remove the two clips holding the two glove box stops. 3 4 isengaging Locate the filter cover. Remove cover by pressing the clips at each side of the cover. (See inset image) Remove and replace cabin air filter, ensuring the filter is placed in the proper direction. Reverse procedure to complete installation. 5 ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Right Tab Behind glove box 10 Minutes 1a Tools Required Open glove box. 1a. Re None right ho 2 If necessary, disengage the damper straps. Applications Tuc s on w o/DCC 2009-2007 Hyundai \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" Revised April-11 CAF2069 4a. Remove the cabin air housing assembly. 4a. Remove the cabin air the filter tray.

Left Knob Right Tab Tip: Pull the clip back (toward -OR- Right Knob the rear of the car) and at the same time, pull it out (toward 1b the center of the glove box). 1b. Remove the rotating knobs on the left and right side. emove the clip on the olding the glove box stop. Tip: Hold the 3 bottom of the Lower the glove box completely. glove box with Remove the cabin air filter housing cover. your hand, as shown. . -OR- 4b. Remove the cabin air filter directly from the housing unit. 4a 4b. Replace the cabin air filter, ensuring the filter is placed in the correct direction. 4b filter and Reverse procedure to filter from complete installation. ©2011 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 5 Minutes Tools Required: Open glove box. Flathead screwdriver Applications Lower completely by di the damper strap. 2010-2009 Kia Borrego 2009-2004 Kia S pec t ra \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2070

Stops 12 Remove the two clips holding the two glove box stops. 3 4 isengaging Locate the filter cover. Remove cover by pressing the clips at each side of the cover. (See inset image) Remove and replace cabin air filter, ensuring the filter is placed in the proper direction. Reverse procedure to complete installation. 5 ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Left Tab Time Behind glove box 5 Minutes 1a Tools Required Tip: Pull the clip back (toward th Flathead Screwdriver same time, pull it out (toward the Open glove box. 1a. R the glo the lef Applications Tip: Hold bottom o 2012-2009 Hyundai Azera glove bo 2009-2009 Hyundai Santa Fe your han 2010-2009 Hyundai Sonata shown. 2010-2008 Kia Optima Disengage the damper st \"Instructions are provided as general guidelines Lower the glove box comp and may not provide every necessary detail for proper removal and installation. Please consult Remove filter from housin your specific vehicle's owner's or repair manual for Reverse procedure to com additional information.\" Apps. Updated Feb-13 CAF2071

Right Tab Left Knob a -OR- Right Knob he rear of the car) and at the 1b e center of the glove box). 1b. Remove the Remove the clips holding rotating knobs on the ove box stops from both left and right side. ft and right side. d the 3 Locate the filter of the access cover. ox with Remove cover by nd, as pressing the clips at each side of the 2 cover. (See inset image) trap. 4 pletely. Pull the filter access cover out and away. 56 ng unit and replace with a new filter. mplete installation. ©2011 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Stops Behind glove box 5 Minutes Open glove box. Remove the two clips hold Tools Required: Flathead Screwdriver 12 Two (2) filters required. Applications 2009-2007 Kia Sorento Locate the two filters with \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2072

1 2 ding the two glove box stops. Disengage the damper strap. 3a Remove filter 2 housing cover by pushing in on the end tabs. 3b 4 5a 5b hin the housing. Remove the first filter by pulling the tab. Slide the second filter to the right and then out. Replace the two filters in reverse order. Reverse procedure to complete installation. 6 ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Caution: Must di Time Passenger side under dash 60 Minutes Tools Required Open glove box. Phillips Head Screwdriver Flathead Screwdriver Locate trim panel. (see arrow) 12mm Socket Ratchet & Extension Two (2) filters required. CAF2073 CAF2074 Note: Two different filters; Remove the two glove box s same access location. above. Note: Only remove tho Applications CAF2073 Mazda Mazda3 Mazda Mazda5 2009-2006 2017-2006 Mazda Mazda3 CAF2074 2005-2004 Updated March-18 Remove the entire glove box assembly from the dash board CAF2073 & CAF2074 OVER

isconnect battery ground cable to perform this installation. 1 2a 2a Remove the upper trim on the Remove the upper trim on the ) right side of glove box first. left side of glove box second. screws as shown 3 ose two screws. 4 5 Pull the entire glove box assembly away from x the right side of the dash board. d. Using a flathead screwdriver, release tabs and disconnect the glove box lamp. 6 ©2018 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

7a 7b Under the dash, p covering the fuse b Using a flathead screwdriver, release the push pin and remove the lower left kick panel. Release Screw Small Fuse Connectors Release Large Fuse Screw Connector 9 Looking at the bottom of the fuse box, locate the following: Two small fuse connectors, One large fuse connector, Two release screws Carefully disconnect the two small connectors and the one large connector by pulling back on their individual release tabs. By hand, turn and release the two release screws. Lower the entire fuse box. CAF2073 & CAF2074 OVER \"Instructions are provided as genera Page 2 and installation. Please consult you

8b Remove the lower kick panel as shown. 8a pull down on the lower kick panel box. Small Fuse Large Fuse Connector Connector (1) Large Fuse Connector (2) 10 From the top of the fuse box, locate the following: One small fuse connector, Two large fuse connectors Continued on Page 3 al guidelines and may not provide every necessary detail for proper removal ur specific vehicle's owner's or repair manual for additional information.\"

Small Fuse Large Fuse Connector Connector (2) Large Fuse Connector (1) 11a 11b From the top of the fuse box: Carefully disconnect the one small connector and the two large connectors by pulling back on their individual release tabs. Tip: Lift fuse box from mounting bracket to assist in disconnecting. Filter C 13 Using a Phillip screwdriver, rem Remove the two nuts holding the mounting bracket. screws holding t Remove the two cabin 15 air filters from the filter housing unit. Tip: Note the position in which they come out. CAF2073 & CAF2074 Page 3

\"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" 12 Remove the entire fuse box from the mounting bracket. (Note: bracket shown in the next picture) Cover Top Bottom 14 14a 14b ps head Replace the filters, move the four ensuring they are placed in the proper direction. the filter cover. Tip: See the tiny arrows on the new filters. Clean and Carefully, reverse inspect the filter procedure to complete housing unit. installation. Remove any 17 additional debris. 16

Location Replacement Caution: Must di Time Passenger side under dash 60 Minutes Tools Required Open glove box. Phillips Head Screwdriver Flathead Screwdriver Locate trim panel. (see arrow) 12mm Socket Ratchet & Extension Two (2) filters required. CAF2073 CAF2074 Note: Two different filters; Remove the two glove box s same access location. above. Note: Only remove tho Applications CAF2073 Mazda Mazda3 Mazda Mazda5 2009-2006 2017-2006 Mazda Mazda3 CAF2074 2005-2004 Updated March-18 Remove the entire glove box assembly from the dash board CAF2073 & CAF2074 OVER

isconnect battery ground cable to perform this installation. 1 2a 2a Remove the upper trim on the Remove the upper trim on the ) right side of glove box first. left side of glove box second. screws as shown 3 ose two screws. 4 5 Pull the entire glove box assembly away from x the right side of the dash board. d. Using a flathead screwdriver, release tabs and disconnect the glove box lamp. 6 ©2018 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

7a 7b Under the dash, p covering the fuse b Using a flathead screwdriver, release the push pin and remove the lower left kick panel. Release Screw Small Fuse Connectors Release Large Fuse Screw Connector 9 Looking at the bottom of the fuse box, locate the following: Two small fuse connectors, One large fuse connector, Two release screws Carefully disconnect the two small connectors and the one large connector by pulling back on their individual release tabs. By hand, turn and release the two release screws. Lower the entire fuse box. CAF2073 & CAF2074 OVER \"Instructions are provided as genera Page 2 and installation. Please consult you

8b Remove the lower kick panel as shown. 8a pull down on the lower kick panel box. Small Fuse Large Fuse Connector Connector (1) Large Fuse Connector (2) 10 From the top of the fuse box, locate the following: One small fuse connector, Two large fuse connectors Continued on Page 3 al guidelines and may not provide every necessary detail for proper removal ur specific vehicle's owner's or repair manual for additional information.\"

Small Fuse Large Fuse Connector Connector (2) Large Fuse Connector (1) 11a 11b From the top of the fuse box: Carefully disconnect the one small connector and the two large connectors by pulling back on their individual release tabs. Tip: Lift fuse box from mounting bracket to assist in disconnecting. Filter C 13 Using a Phillip screwdriver, rem Remove the two nuts holding the mounting bracket. screws holding t Remove the two cabin 15 air filters from the filter housing unit. Tip: Note the position in which they come out. CAF2073 & CAF2074 Page 3

\"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" 12 Remove the entire fuse box from the mounting bracket. (Note: bracket shown in the next picture) Cover Top Bottom 14 14a 14b ps head Replace the filters, move the four ensuring they are placed in the proper direction. the filter cover. Tip: See the tiny arrows on the new filters. Clean and Carefully, reverse inspect the filter procedure to complete housing unit. installation. Remove any 17 additional debris. 16

Location Replacement Time Behind glove box 10 Minutes Tools Required None Applications 2012-2011 Hyundai Azera (w/o Dual AC) 2013-2011 Hyundai Equus 2013-2009 Hyundai Genesis \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" Apps. Updated Feb-13 CAF2075

Left Tab Stops Right Tab 1 Open glove box. Remove the clips holding the glove box stops from both the left and right side. Tip: Pull each clip back (toward the rear of the car) and at the same time, pull them out (toward the center of the glove box). 2 Lower the glove box completely. Remove the filter access cover by pinching the tab. Be sure to note the air flow direction. Remove the cabin air filter from the filter housing. 3 Replace the cabin air filter, ensuring the filter is placed in the correct direction. Reverse procedure to complete installation. 4 ©2013 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 5 Minutes Tools Required None Applications Push in o 2010-2007 Maz da CX-7 Remove the filter cover b it toward you. \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2076

Open glove box. 2 Disengage the damper strap by 1 pushing it to the left. 3a 3b on left and then right side to fully release the compartment. 4 5 by simply pulling Pull the dirty filter straight out. Reverse procedure to complete installation. ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 5 Minutes Tools Required None Applications Mazda6 2008-2003 Mazda \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" Apps. Updated April-11 CAF2077

Open the glove box. Unclip the tab holding the slide and hook on the right side of the glove box. 1 Press inward on each side until the tabs release. Lower glove box completely. 2 Pulling from the bottom, gently unclip the filter access cover. Remove the filter access cover, exposing the dirty filter. 3 Pull the dirty filter straight out. Reverse procedure to complete installation. 4 ©2009 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 5 Minutes Tools Required Open glove box. None Two (2) filters required. Disengage the damper s Lower glove box comple Applications Remove the filter cover b 2006-2003 Maz da MPV it toward you. 2010-2004 Maz da RX-8 \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2078

12 Press inward on each side until the tabs release. strap. 34 etely. Locate the filter cover. Push in tabs on left and right sides of housing. 5 6 by simply pulling Pull the dirty filter straight out. Reverse procedure to complete installation. ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Hood Push Pins Passenger side under 5 Minutes hood and cowl. Cowl Tools Required None Hood Cowl Filter & Filter Housing Applications 2009-2000 Honda S2000 New July-09 \"Instructions are provided as proper removal and installati CAF2080 for additional information.\"

d Open the hood. Remove the two push pins on the Windshield passenger side of the cowl. Weatherstrip Pull back weatherstrip from passenger side of cowl. 1 d Lift cowl away from the windshield. Windshield Remove filter and filter housing. Replace the cabin air filter. Reverse procedure to complete installation. Weatherstrip 2 s general guidelines and may not provide every necessary detail for ion. Please consult your specific vehicle's owner's or repair manual ©2009 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 35 Minutes Tools Required Open glove box. Phillips Head Screwdriver 10mm Socket Ratchet Box Cutter or Knife Two (2) filters required. Applications 2001-1999 Honda Prelude New April-10 CAF2081AOVER

A B 12 Remove the two glove box stops by pressing on the clips. (see A) Remove the screw holding the slide and hook. (see B and inset image) Lower the glove box completely. Remove the two glove box screws. (see circled) 3 Remove glove box assembly. Remove the two bolts holding the support bar in place. (see circled) 4 Note: For first time installations, cut the mid (see arrows) section of the plastic support bar. Remove the support bar. 5 ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

2 1 6 Remove the first filter (1) b Remove the second filter (2 Unclip the filter cover from the bottom down and then out. (see arrow) by pulling down and then out. Remove the filter cover. CAF2081 9 Page 2 \"Instructions are provided as general guidelines an Please consult your specific vehicle's owner's or re

7 8 Clean and inspect the filter housing unit. by pulling the bottom tab. 2) by pulling the top tab 9 Push the filters out of their frame in the direction of the arrow. (see arrow) 10 Replace the filters, ensuring they are placed in the proper direction. - Reverse procedure to complete installation. 10 nd may not provide every necessary detail for proper removal and installation. epair manual for additional information.\"

Location Replacement Time Behind glove box 5 Minutes Tip: I Tools Required: scr None Open glove box. Applications Lower the glove box com 2008-2007 Honda Fit \"Instructions are provided as general guidelines and may not provide every necessary detail for proper removal and installation. Please consult your specific vehicle's owner's or repair manual for additional information.\" New April-10 CAF2082

If necessary, remove the two 2 rews from the bottom of the glove box. (see above) 1 Push both sides inward to release the compartment. 3 4a 4b mpletely. Push in tabs on left and right sides of housing and pull it towards you. Remove the cabin air filter and housing assembly. Remove the cabin air filter from the tray. Replace the cabin air filter, ensuring the filter is placed in the proper direction. Reverse procedure to complete installation. 5 ©2010 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092

Location Replacement Time Behind glove box 10 Minutes Open glove box. Locate damper strap (left Tools Required: Box Cutter or Knife Applications Disengage the damper s Lower the glove box ass 2006-2004 Mitsubishi Lancer 2006-2003 Mitsubishi Outlander Note: \"Instructions are provided as general guidelines For first time installations, use knife to cut the cover along the lines to and may not provide every necessary detail for form a rectangular opening. proper removal and installation. Please consult Remove the two screws your specific vehicle's owner's or repair manual for additional information.\" Apps. Updated Dec-11 CAF2083

1 2 t) and tab (right). Push in on right tab to release the compartment. 3a 3b 3c strap by sliding and pushing it out, then removing it as shown above. sembly completely. 4 5 s from the filter housing. Remove the cabin air filter. Reverse procedure to complete installation. ©2011 ~ Mighty Distributing System of America ~ 650 Engineering Drive, Norcross, GA 30092