2021-Online-Catalogue-AU-FINAL

51PRODUCT CATALOGUE 2021HOSE SELECTION & SERVICE LIFE RECOMMENDATIONS Extracts from SAE J1273 DEC2014: Recommended Practices for Hydraulic Hose Assemblies 6FRSH—SAE J1273 provides guidelines for selection, routing, fabrication, installation, replace-ment, maintenance, and storage of hose and hose assemblies for uid-power systems. Many of these�flSAE Recommended Practices also may be suitable for other hoses and systems. +RVH 6HOHFWLRQ DQG 5RXWLQJ—A wide variety of interacting factors in uence hose service life andfl�the ability of each uid-power system to operate satisfactorily, and the combined effects of these����lffactors on service life are often unpredictable. Therefore, these documents should not be construedas design standards. For applications outside the speci cations in SAE J517, SAE J514, or otherf�relevant design standards, performance of hose assemblies should be determined by appropriatetesting. Carefully analyze each system. Then design routings and select hose and related compo-nents to meet the system-performance and hose-service-life requirements, and to minimize the risksof personal injury and/or property damage. Consider the following factors:5.1 System Pressures—Excessive pressure can accelerate hose assembly failure. Analyze the steady-state pressures, and the frequency and amplitude of pressure surges, such as pulses and spikes. These are rapid and transient rises in pressure which may not be indicated on many common pressure gauges and can be identi ed best on high-frequency-response electronic measuring instru-f�ments.For maximum hose service life, hose selection should be based on a system pressure, including surges, that is less than the hose maximum working pressure. Hose may be used above its maxi-mum working pressure where reduced life expectancy is acceptable. SAE J1927 provides one method to help predict wire-reinforced hose service life for a given hydraulic application, where the surge pressure peaks vary, and/or the highest pressure peaks occur infrequently.5.2 Suction—For suction applications, such as inlet ow to pumps, select hose to withstand both the �flnegative and positive pressures the system imposes on the hose.5.3 External Pressure—In certain applications, such as in autoclaves or under water, the external environmental pressures may exceed the uid pressure inside the hose. In these applications, con-�flsider the external pressures, and if necessary, consult the manufacturers.5.4 Temperature—Exceeding hose temperature ratings may signi cantly reduce hose life. Select f�hose so the uid and ambient temperatures, both static and transient, fall within the hose ratings. The �fleffects of external heat sources should not raise the temperature of the hose above its maximum op-erating temperature. Select hose, heat shields, sleeving, and other methods for these requirements,�����������������l����������������������������f�����������l��������������www.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeHYDRAULIC HOSE - AGENCY RANGE

52PRODUCT CATALOGUE 20213 - 2HOSE SELECTION & SERVICE LIFE RECOMMENDATIONS (cont’d)5.5 Permeation—Permeation, or effusion, is seepage of uid through the hose. Certain materials in flhose construction are more permeable than others. Consider the effects of permeation whenselecting hose, especially with gaseous uids. Consult the hose and uid manufacturers for flflpermeability information.5.6 Hose-Material Compatibility—Variables that can affect compatibility of system uids with hose flmaterials include, but are not limited to:a. Fluid pressureb. Temperaturec. Concentrationd. Duration of exposureBecause of permeation (see 5.5), consider compatibility of system uids with the hose, tube, cover, reinforcement, and ttings. Consult the uid and hose manufacturers for compatibility information.NOTE— Many uid/elastomer compatibility tables in manufacturers’ catalogs show ratings based on  uids at 21 °C, room temperature. These ratings may change at other temperatures. Carefully read the notes on the compatibility tables, and if in doubt, consult the manufacturer.5.7 Environment—Environmental conditions can cause hose and tting degradation. Conditions to evaluate include, but are not limited to:a. Ultraviolet lightb. Salt waterc. Air pollutantsd. Temperature (see 5.4)e. Ozonef. Chemicalsg. Electricityh. AbrasionIf necessary, consult the manufacturers for more information.5.8 Static-Electric Discharge—Fluid passing through hose can generate static electricity resulting in static-electric discharge. This may create sparks that can puncture hose. If this potential exists, select hose with suf cient conductivity to carry the static-electric charge to ground.5.9 Sizing—The power transmitted by pressurized uid varies with pressure and rate of ow. Select hose with adequate size to minimize pressure loss, and to avoid hose damage from heat generation or excessive velocity. Conduct calculations, or consult the manufacturers for sizing at ow velocities.5.10 Unintended Uses—Hose assemblies are designed for the internal forces of conducted uids. Do not pull hose or use it for purposes that may apply external forces for which the hose or ttings were not designed.5.11 Speci cations and Standards—When selecting hose and ttings for speci c applications, refer to applicable government, industry, and manufacturer’s speci cations and standards.www.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeHYDRAULIC HOSE - AGENCY RANGE

53PRODUCT CATALOGUE 20213 - 3HOSE SELECTION & SERVICE LIFE RECOMMENDATIONS (cont’d)5.12 Unusual Applications—Applications not addressed by the manufacturer or by industry stan-dards may require special testing prior to selecting hose.5.13 Hose Cleanliness—The cleanliness requirements of system components, other than hose, will determine the cleanliness requirements of the application. Consult the component manufacturers’ cleanliness information for all components in the system. Hose assemblies vary in cleanliness levels; therefore, specify hose assemblies with adequate cleanliness for the system.5.14 Hose Fittings—Selection of the proper hose ttings for the hose and application is essential for proper operation and safe use of hose and related assembly equipment. Hose ttings are quali ed with the hose. Therefore, select only hose ttings compatible with the hose for the applications.Improper selection of hose ttings or related assembly equipment for the application can result in injury or damage from leaks, or from hose assemblies blowing apart (see 4.2, 6.2, 6.3, and 6.4).5.15 Vibration—Vibration can reduce hose service life. If required, conduct tests to evaluate the fre-quency and amplitude of system vibration. Clamps or other means may be used to reduce the effects of vibration. Consider the vibration requirements when selecting hose and predicting service life.5.16 Hose Cover Protection—Protect the hose cover from abrasion, erosion, snagging, and cutting. Special abrasion-resistant hoses and hose guards are available for additional protection. Route hose to reduce abrasion from hose rubbing other hose or objects that may abrade it.5.17 External Physical Abuse—Route hose to avoid:a. Tensile loadsb. Side loadsc. Flatteningd. Thread damagee. Kinkingf. Damage to sealing surfacesg. Abrasionh. Twisting5.18 Swivel-Type Adapters—Swivel-type ttings or adapters do not transfer torque to hose while be-ing tightened. Use these as needed to prevent twisting during installation.5.19 Live Swivels—If two components in the system are rotating in relation to each other, live swiv-els may be necessary. These connectors reduce the torque transmitted to the hose.5.20 Slings and Clamps—Use slings and clamps to support heavy or long hose and to keep it away from moving parts. Use clamps that prevent hose movement that will cause abrasion.5.21 Minimum Bend Radius—The minimum bend radius is de ned in SAE J343 and is speci ed in other SAE standards and hose manufacturer’s product literature. Routing at less than minimum bend radius may reduce hose life. Sharp bending at the hose/ tting juncture may result in leaking, hose rupturing, or the hose assembly blowing apart (see 4.2)5.22 Elbows and Adapters—In special cases, use elbows or adapters to relieve hose strain.5.23 Lengths—Unnecessarily long hose can increase pressure drop and affect system performance. n ct- e , on d o g in ect ct on s.. efer 1002SROwww.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCceOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeHYDRAULIC HOSE - AGENCY RANGE

54PRODUCT CATALOGUE 2021HOSE SELECTION & SERVICE LIFE RECOMMENDATIONS (cont’d)When pressurized, hose that is too short may pull loose from its ttings, or stress the tting connec-tions, causing premature metallic or seal failures. When establishing hose length, use the following practices:5.23.1 MOTION ABSORPTION—Provide adequate hose length to distribute movement and prevent bends smaller than the minimum bend radius.5.23.2 HOSE AND MACHINE TOLERANCES—Design hose to allow for changes in length due to machine motion and tolerances.5.23.3 HOSE LENGTH CHANGE DUE TO PRESSURE—Design hose to accommodate length changes from changing pressures. Do not cross or clamp together high- and low-pressure hoses. The difference in length changes could wear the hose covers.5.24 Hose Movement and Bending—Hose allows relative motion between system components. Analyze this motion when designing hose systems. The number of cycles per day may signi cantly affect hose life. Also avoid multiple planes of motion and twisting motion. Consider the motion of the hose when selecting hose and predicting service life. In applications that require hose to move or bend, use these practices:5.24.1 BEND IN ONLY ONE PLANE TO AVOID TWISTING5.24.2 PREVENT HOSE BENDING IN MORE THAN ONE PLANE—If hose follows a compound bend, couple it into separate segments, or clamp it into segments that ex in only one plane. +RVH ,QVWDOODWLRQ DQG 5HSODFHPHQW—Use the following practices when installing hose assem-blies in new systems or replacing hose assemblies in existing systems:7.1 Pre-Installation Inspection—Before installing hose assemblies, examine:a. Hose length and routing for compliance with original designb. Assemblies for correct style, size, length, and visible nonconformitiesc. Fitting sealing surfaces for burrs, nicks, or other damageNOTE— When replacing hose assemblies in existing systems, verify that the replacement is of equal quality to the original assembly.7.2 Handling During Installation—Handle hose with care during installation. Kinking hose, or bend-ing at less than minimum bend radius may reduce hose life. Avoid sharp bending at the hose/ tting juncture (see 5.21).7.3 Twist Angle and Orientation—Pressure applied to a twisted hose may shorten the life of the hose or loosen the connections. To avoid twisting, use the hose lay line or marking as a reference.7.4 Securement and Protection—Install necessary restraints and protective devices. Determine that such devices do not create additional stress or wear points.7.5 Routing—Review proper routing practices provided in Section 5 and make appropriate correc-tions to obtain optimum performance.www.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeHYDRAULIC HOSE - AGENCY RANGE

55PRODUCT CATALOGUE 2021HOSE SELECTION & SERVICE LIFE RECOMMENDATIONS (cont’d)7.6 Assembly Torque—The connection end of a hose tting is normally threaded to obtain a tight pressure seal when attached to a port, an adapter, or another tting. Sometimes bolts or screws pro-vide the threaded connection. Each size and type of connection requires different torque values, and these may vary due to type of material or exterior coating.Follow appropriate torquing instructions to obtain a proper pressure seal without over-torquing. A properly calibrated torque wrench should be used to tighten each connection, except when the manu-facturer speci es tightening a speci ed number of hex at turns beyond nger tight to obtain a seal.7.7 System Checkouts—In hydraulic or other liquid systems, eliminate all air entrapment after com-pleting the installation. Follow manufacturers’ instructions to test the system for possible malfunctions and leaks.7.7.1 TO AVOID INJURY DURING SYSTEM CHECKOUTS:a. Do not touch any part of the system when checking for leaks (see 4.1).b. Stay out of potentially hazardous areas while testing hose systems (see Section 4).c. Relieve system pressure before tightening connections. 0DLQWHQDQFH ,QVSHFWLRQ—A hose and tting maintenance program may reduce equipment down-time, maintain peak operating performance, and reduce the risk of personal injury and/or propertydamage. The user should design and implement a maintenance program that suits the speci c ap-plication and each speci c hose in that application.8.1 Inspection Frequency—Evaluate factors such as the nature and severity of the application, past history, and manufacturers’ information to establish the frequency of visual inspections and functional tests.8.2 Visual Inspection (Hose and Fittings)—Visually inspect hose and ttings for:a. Leaks at hose tting or in hoseb. Damaged, cut, or abraded coverc. Exposed reinforcementd. Kinked, crushed, attened, or twisted hosee. Hard, stiff, heat cracked, or charred hosef. Blistered, soft, degraded, or loose coverg. Cracked, damaged, or badly corroded ttingsh. Fitting slippage on hosei. Other signs of signi cant deteriorationIf any of these conditions exist, evaluate the hose assemblies for correction or replacement.8.3 Visual Inspection (All Other Components)—When visually inspecting hose and ttings, inspect for related items including:a. Leaking portsb. Damaged or missing hose clamps, guards, or shieldsc. Excessive dirt and debris around hosed. System uid: level, type, contamination, condition, and air entrainmentIf any of these are found, address them appropriately.www.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeHYDRAULIC HOSE - AGENCY RANGE

56PRODUCT CATALOGUE 20213 - 6HOSE SELECTION & SERVICE LIFE RECOMMENDATIONS (cont’d)8.4 Functional Test—Functional tests determine if systems with hose are leak free and operating properly. Carry out functional tests per information from equipment manufacturers.9. Hose Storage—Age control and the manner of storage can affect hose life. Use the followingpractices when storing hose.9.1 Age Control—Maintain a system of age control to determine that hose is used before its shelf life has expired. Shelf life is the period of time when it is reasonable to expect the hose to retain full capabilities for rendering the intended service.Store hose in a manner that facilitates age control and rst-in, rst-out usage based on manufactur-ing date on hose or hose assembly. Per SAE J517:a. Shelf life of rubber hose in bulk form, or in hose assemblies passing visual inspection andproof test, is forty quarters (ten years) from the date of vulcanization.b. Shelf life of thermoplastic and polytetra uoroethylene hose is considered to be unlimited.www.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeHYDRAULIC HOSE - AGENCY RANGE

57PRODUCT CATALOGUE 20213 - 7NOMOGRAPHIC CHARTFlowHose I.D.VelocityFlow Capacity of Hose AssembliesRecommended Flow VelocitiesUse the chart below to determine Hose I.D. based on Flow and Velocity. Conversely, it can be used to determine Velocity, based on Flow and Hose I.D., or Flow based on Velocity and Hose I.D. Example: To determine the Hose I.D. needed to transport 20 gallons per minute (Gal/min)...Draw a straight line from 20 Gal/min on the left to recom-mended maximum velocity for pressure lines on the left. The line intersects the middle column indicating that a 3/4” I.D. (-12) hose should be the smallest hose used.Please note this chart uses Imperial Gallons, not U.S. Gallons.EMHwww.hydraulink.com100 2 SROTCENNO C D IUL F KN I LUARDY H © t hg i r ypoCwww.hOur product range is constantly evolving and Hydraulink reserve the right to change technical specifications without noticeOur HYDRAULIC HOSE - AGENCY RANGE

58PRODUCT CATALOGUE 20213-8HYDRAULIC HOSE INDEXEXTREMELY HIGH PRESSURE HOSEFOUR/SIX SPIRAL WIREHOSEEFG6KPage 3 - 13FOUR/SIX SPIRAL WIREHOSEEFG5KPage 3 - 14FOUR SPIRAL WIREHOSEEFG4KPage 3 - 15FOUR SPIRAL WIREHOSEEFG3KPage 3 - 15HIGH PRESSURE HOSETWO WIRE BRAID HOSEG2Page 3 - 16HIGH TEMP. TWO WIREBRAID HOSEG2XHPage 3 - 17TWO WIRE BRAIDSLIMLINE HOSEM2TPage 3 - 17TWO WIRE BRAIDSLIMLINE HOSE - MTFCOVERM2T-MTFPage 3 - 18TWINLINE TWO WIREBRAID HOSECM2TDL-XTFPage 3 - 18ONE/TWO WIRE BRAIDHOSEM3KPage 3 - 19TWO WIRE BRAID HOSEM4KPage 3 - 19TWO WIRE BRAID HOSE- XTF COVERM4K-XTFPage 3 - 21TWO WIRE BRAID HOSEM5KPage 3 - 21TWO WIRE BRAID HOSEM6KPage 3 - 22TWO WIRE BRAID JACKHOSEJ2ATPage 3 - 22

59PRODUCT CATALOGUE 20213-9HYDRAULIC HOSE INDEXMEDIUM PRESSURE HOSEONE WIRE BRAID HOSEG1Page 3 - 23HIGH TEMP. OIL/AIRRETURNACPPage 3 - 23HIGH TEMP. OIL/AIRRETURNACRPage 3 - 24WATER JETTINGPOWERCLEAN™ WIREBRAID HOSEPCPage 3 - 24LOW PRESSURE HOSEPUSH-LOCK FIBREBRAID HOSELOLPage 3 - 25PUSH-LOCK FIBREBRAID HOSELOCPage 3 - 25PUSH-LOCK FIBREBRAID HOSEGTHPage 3 - 27MultiMaster® RETURNAND SUCTIONGMV-MEGAFLEXPage 3 - 28MAXIMUS PETROLEUMSUCTIONRWPS09Page 3 - 28PUSH-LOCK FIBREBRAID HOSEG3HPage 3 - 29

60PRODUCT CATALOGUE 20213-10HYDRAULIC HOSE INDEXFLEET APPLICATION HOSEONE WIRE NOMINALBORE HOSEC5CPage 3 - 30ONE WIRE NOMINALBORE HOSEC5DPage 3 - 31ONE WIRE NOMINALBORE HOSEC5EPage 3 - 32ONE WIRE NOMINALBORE HOSEC5MPage 3 - 33POWER STEERING HOSEPS188Page 3 - 33PTFE HOSESTAINLESS BRAIDEDPTFE HOSER14Page 3 - 34

61PRODUCT CATALOGUE 20213-11HYDRAULIC HOSE INDEXTHERMOPLASTIC HOSEFIBRE BRAIDTHERMOPLASTIC HOSER7Page 3 - 34FIBRE BRAIDTHERMOPLASTIC HOSER7NCPage 3 - 36TWINLINETHERMOPLASTIC HOSER7TPage 3 - 36FIBRE BRAIDTHERMOPLASTIC HOSER8XPage 3 - 38FIBRE BRAIDTHERMOPLASTIC HOSER8XNCPage 3 - 38TWINLINETHERMOPLASTIC HOSER8XTPage 3 - 40FIBRE BRAIDTHERMOPLASTIC HOSER18Page 3 - 40TWINLINETHERMOPLASTIC HOSER18TPage 3 - 42PAINTSPRAY HOSEONE WIRE BRAIDTHERMOPLASTICPS1BPage 3 - 42AUTOMOTIVE HOSELPG SERVICE HOSELPGPage 3 - 43LPG VAPORISER HOSEMVAPPage 3 - 43FUEL LINE27000FUELPage 3 - 44VACUUM HOSE27000VACPage 3 - 44

62PRODUCT CATALOGUE 20213-12HYDRAULIC HOSE INDEXFIRE SUPPRESSION HOSEONE WIRE BRAID HOSERFSPage 3 - 45MULTIPURPOSE HOSEPremoflex MULTI-PURPOSE HOSEPREMOFLEXPage 3 - 45Terminator MULTI-PURPOSE HOSETERMINATORPage 3 - 46

63PRODUCT CATALOGUE 20213-13HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.EXTREMELY HIGH PRESSURE HOSEEFG6KFOUR/SIX SPIRAL WIRE HOSESPIRAL WIRE REINFORCED HOSE - SAE 100R15•Due to manufacturing tolerances, external dimension is an average.•Recommended for: Extremely high pressure and high impulse hydraulicapplications.•Internal tube: -6, -8, -10, -12, -16, -20: Nitrile based; -24: Neoprene based.•Reinforcement: Four (six for -20, -24) alternating layers of spiralled, hightensile steel wire.•External cover: Neoprene based, MSHA approved.•Temperature range: -40°C to +121°C•Standards: SAE 100R15. Meets or exceeds performance requirements ofEN 856 4SP (-8) and EN 856 4SH (-12, -16)•Characteristics: Extremely flexible. Compatible with biodegradablehydraulic fluids like synthetic esters, polyglycols and vegetable oils andpetroleum-based fluids in sizes -06 to -20 (not -24)•Optional: EFG6K-MTF: the range of EFG6K is also available with theGates special MegaTuff™ cover which offers 300 times the abrasionresistance of the standard cover as per ISO 6945, superiorozone/weathering resistance - please contact Hydraulink for further detailsand availability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)6EFG6K06103/820.56000420240001680658EFG6K08121/224.060004202400016809010EFG6K10165/827.6600042024000168010012EFG6K12193/431.4600042024000168012016EFG6K1625138.7600042024000168015020EFG6K20311.1/450.0600042024000168021024EFG6K24381.1/257.4600042024000168025032EFG6K3251271.16000420240001680635

64PRODUCT CATALOGUE 20213-14HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.EXTREMELY HIGH PRESSURE HOSEEFG5KFOUR/SIX SPIRAL WIRE HOSESPIRAL WIRE REINFORCED HOSE - SAE 100R13•Due to manufacturing tolerances, external dimension is an average.•Recommended for: Extremely high pressure and high impulse hydraulicapplications.•Internal tube: -6 to -20•Nitrile based: -24, -32: Neoprene based.•Reinforcement: Four (six for -20, to -32) alternating layers of spiralled, hightensile steel wire.•External cover: Neoprene based, MSHA approved.•Temperature range: -40°C to +121°C•Standards: EN 856 R13. SAE 100R13. Meets or exceeds performancerequirements of EN 856 4SP (-10, -12) and EN 856 4SH (-20).•Characteristics: Extremely flexible. Compatible with biodegradablehydraulic fluids like synthetic esters, polyglycols, vegetable oils andpetroleum-based fluids in sizes -06 to -20 (not -24 or -32).•Optional: EFG5K-MTF: the range of EFG5K is also available with theGates MegaTuff™ cover which offers 300 times the abrasion resistance ofthe standard cover as per ISO 6945, superior ozone/weathering resistance- please contact Hydraulink for further details and availability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)8EFG5K08121/224.050003502000014009010EFG5K10165/827.6500035024000140010012EFG5K12193/431.4500035024000140012016EFG5K1625138.7500035024000140015020EFG5K20311.1/450500035024000140021024EFG5K24381.1/257.4500035024000140025032EFG5K32512715000350240001400635

65PRODUCT CATALOGUE 20213-15HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.EXTREMELY HIGH PRESSURE HOSEEFG4KFOUR SPIRAL WIRE HOSESPIRAL WIRE REINFORCED HOSE - SAE 100R12•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Extremely high pressure and high impulse hydraulicapplications.•Internal tube: Nitrile based.•Reinforcement: Four alternating layers of spiralled, high tensile steel wire.•External cover: Neoprene based, MSHA approved.•Temperature range: -40°C to +121°C•Standards: Gates proprietary. EN 856 R12. SAE 100R12. Meets orexceeds performance requirements of EN 856 4SP (-16, -20).•Characteristics: Extremely flexible. Compatible with biodegradablehydraulic fluids like synthetic esters, polyglycols and vegetable oils as wellas petroleum-based fluids in sizes -06 to -20 (not -24).•Optional: EFG4K-MTF: the range of EFG4K is also available with theGates special MegaTuff™ cover which offers 300 times the abrasionresistance of the standard cover as per ISO 6945, superior ozone andweathering resistance - please contact Hydraulink for further details andavailability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)6EFG4K06103/820.54000280160001120658EFG4K08121/224.040002801600011209010EFG4K10165/827.6400028016000112010012EFG4K12193/430.7400028016000112012016EFG4K1625138.0400028016000112015020EFG4K20311.1/447.04000280160001120210EXTREMELY HIGH PRESSURE HOSEEFG3KFOUR SPIRAL WIRE HOSESPIRAL WIRE REINFORCED HOSE - SAE 100R12•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Extremely high pressure and high impulse hydraulicapplications.•Internal tube: Neoprene based.•Reinforcement: Four alternating layers of spiralled, high tensile steel wire.•External cover: Neoprene based, MSHA approved.•Temperature range: -40°C to +121°C•Standards: Gates proprietary. EN 856 R12. SAE 100R12.•Characteristics: Extremely flexible.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)24EFG3K24381.1/253.530002101200084050032EFG3K3251266.8300021012000840630

66PRODUCT CATALOGUE 20213-16HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.HIGH PRESSURE HOSEG2TWO WIRE BRAID HOSEBRAIDED WIRE REINFORCED HOSE - SAE 100R2 Type AT•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: SAE 100R2AT. SAE 100R2S. EN 853 2SN. ISO 1436.•Characteristics: G2 hose is compatible with biodegradable hydraulic fluidslike synthetic esters, polyglycols and vegetable oils as well as petroleum-based fluids.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3G20353/1613.26000415240001660904G20461/415.058004002320016001005G20585/1616.350003502000014001106G206103/818.848003301920013201308G208121/221.8400027516000110018010G210165/825.1362525014500100020012G212193/429.031002151240086024016G21625137.62400165960066030020G220311.1/447.51825125730050042024G224381.1/253.6130090520036050832G23251266.61175804700324635

67PRODUCT CATALOGUE 2021HYDRAULIC HOSEHIGH PRESSURE HOSEM2T-MTFTWO WIRE BRAID SLIMLINE HOSE - MTF COVERBRAIDED WIRE REINFORCED HOSE - SAE 100R16MEGATUFF COVER•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based MegaTuff (MTF) abrasion resistant.MSHA approved. Dual green stripe layline.•Temperature range: -40°C to +100°C.•Standards: Gates proprietary. Exceeds SAE 100R16.•Characteristics: M2T hose has smaller exterior dimensions andsignificantly tighter bend radius than specified in SAE 100R16.•Optional: M2T-MTF: the range of M2T is also available with the Gatesspecial MegaTuff™ cover which offers 300 times the abrasion resistanceof the standard cover as per ISO 6945, superior ozone/weatheringresistance - please contact Hydraulink for further details and availability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure -psiWorkingpressure -barMin burstpressure -psiMin burstpressure -barMin bendradius(mm)4M2T-MTF0461/413.76000420240001680386M2T-MTF06103/817.55000350200001400508M2T-MTF08121/220.64300300720012007110M2T-MTF10165/824.138002601520010407612M2T-MTF12193/427.93500240140009609616M2T-MTF1625135.1250014010000560114HIGH PRESSURE HOSECM2TDL-XTFTWINLINE TWO WIRE BRAID HOSETWINLINE BRAIDED WIRE REINFORCED HOSE - SAE100R16•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure and return lines such as boom arm andforklift applications.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved. Dual green stripelayline.•Temperature range: -40°C to +100°C.•Standards: Gates proprietary. EN 857 2SC. ISO 1436.•Characteristics: No need to use clamps as the two lines are vulcanisedtogether to form one single unit. CM2T twin hose is compatible withbiodegradable hydraulic fluids like synthetic esters, polyglycols andvegetable oils as well as petroleum-based fluids.•Gates recommends minimum split length of 250 mm depending on theapplication. Do not expose hose reinforcement when splitting hoses.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)6CM2TDL-XTF06103/817.74800330192001320908CM2TDL-XTF08121/220.84000275160001100130

68PRODUCT CATALOGUE 20213-18HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.HIGH PRESSURE HOSEM2T-MTFTWO WIRE BRAID SLIMLINE HOSE - MTF COVERBRAIDED WIRE REINFORCED HOSE - SAE 100R16MEGATUFF COVER•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based MegaTuff (MTF) abrasion resistant.MSHA approved. Dual green stripe layline.•Temperature range: -40°C to +100°C.•Standards: Gates proprietary. Exceeds SAE 100R16.•Characteristics: M2T hose has smaller exterior dimensions andsignificantly tighter bend radius than specified in SAE 100R16.•Optional: M2T-MTF: the range of M2T is also available with the Gatesspecial MegaTuff™ cover which offers 300 times the abrasion resistanceof the standard cover as per ISO 6945, superior ozone/weatheringresistance - please contact Hydraulink for further details and availability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure -psiWorkingpressure -barMin burstpressure -psiMin burstpressure -barMin bendradius(mm)4M2T-MTF0461/413.76000420240001680386M2T-MTF06103/817.55000350200001400508M2T-MTF08121/220.64300300720012007110M2T-MTF10165/824.138002601520010407612M2T-MTF12193/427.93500240140009609616M2T-MTF1625135.1250014010000560114HIGH PRESSURE HOSECM2TDL-XTFTWINLINE TWO WIRE BRAID HOSETWINLINE BRAIDED WIRE REINFORCED HOSE - SAE100R16•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure and return lines such as boom arm andforklift applications.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved. Dual green stripelayline.•Temperature range: -40°C to +100°C.•Standards: Gates proprietary. EN 857 2SC. ISO 1436.•Characteristics: No need to use clamps as the two lines are vulcanisedtogether to form one single unit. CM2T twin hose is compatible withbiodegradable hydraulic fluids like synthetic esters, polyglycols andvegetable oils as well as petroleum-based fluids.•Gates recommends minimum split length of 250 mm depending on theapplication. Do not expose hose reinforcement when splitting hoses.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)6CM2TDL-XTF06103/817.74800330192001320908CM2TDL-XTF08121/220.84000275160001100130

69PRODUCT CATALOGUE 20213-19HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.HIGH PRESSURE HOSEM3KONE/TWO WIRE BRAID HOSEBRAIDED WIRE REINFORCED HOSE - SAE 100R17•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: -4, -5, -6, -8: one braid of high tensile steel wire; -10, -12, -16: two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: SAE 100R17. ISO 11237-1. Meets or exceeds EN 8571SC/2SC performance requirements.•Characteristics: M3K hose is compatible with biodegradable hydraulicfluids like synthetic esters, polyglycols and vegetable oils as well aspetroleum-based fluids.•Optional: M3K-XTF: the range of M3K is also available with the Gatesspecial XtraTuff™ cover which offers 25 times the abrasion resistance ofthe standard cover as per ISO 6945, superior ozone/weathering resistance- please contact Hydraulink for further details and availability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4M3K0461/412.2300021012000840506M3K06103/816.0300021012000840658M3K08121/220.23000210120008409012M3K12193/429.030002101200084012016M3K1625137.7300021012000840150HIGH PRESSURE HOSEM4KTWO WIRE BRAID HOSEBRAIDED WIRE REINFORCED HOSE - SAE 100R19•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: SAE 100R19. ISO 11237-1. Meets or exceeds EN 857 2SCperformance requirements.•Characteristics: Alternative to spiral hoses in high pressure lines whereflexibility is required. M4K hose is compatible with biodegradable hydraulicfluids like synthetic esters, polyglycols and vegetable oils as well aspetroleum-based fluids.•Special item - please contact Hydraulink for further details and availability.•-XTF (XtraTuff™) hose lasts up to 25 times longer than standard hoseduring hose-to-hose and hose-to-metal abrasion tests per ISO 6945.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4M4K0461/413.74000275160001100506M4K06103/817.5400027516000110065

70PRODUCT CATALOGUE 20213-20HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)8M4K08121/220.840002751600011009010M4K10165/825.0400027516000110010012M4K12193/429.0400027516000110012016M4K1625138.64000275160001100114

71PRODUCT CATALOGUE 20213-21HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.HIGH PRESSURE HOSEM4K-XTFTWO WIRE BRAID HOSE - XTF COVERBRAIDED WIRE REINFORCED HOSE - SAE 100R19•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: SAE 100R19. ISO 11237-1. Meets or exceeds EN 857 2SCperformance requirements.•Characteristics: Alternative to spiral hoses in high pressure lines whereflexibility is required. M4K hose is compatible with biodegradable hydraulicfluids like synthetic esters, polyglycols and vegetable oils as well aspetroleum-based fluids.•Special item - please contact Hydraulink for further details and availability.•-XTF (XtraTuff™) hose lasts up to 25 times longer than standard hoseduring hose-to-hose and hose-to-metal abrasion tests per ISO 6945.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4M4K-XTF0461/413.74000280160001120506M4K-XTF06103/817.54000280160001120658M4K-XTF08121/220.840002801600011209010M4K-XTF10165/825.0400028016000112010012M4K-XTF12193/429.04000280160001120120HIGH PRESSURE HOSEM5KTWO WIRE BRAID HOSEBRAIDED WIRE REINFORCED HOSE - 5000PSI•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: Exceeds ISO 18752 Grade B.•Characteristics: Alternative to spiral hoses in high pressure lines whereflexibility is required. M5K hose is compatible with biodegradable hydraulicfluids like synthetic esters, polyglycols and vegetable oils as well aspetroleum-based fluids.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4M5K0461/4145000350200001400506M5K06103/817.85000350200001400638M5K08121/221.6500035020000140089

72PRODUCT CATALOGUE 20213-22HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.HIGH PRESSURE HOSEM6KTWO WIRE BRAID HOSEBRAIDED WIRE REINFORCED HOSE - 6000PSI•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications. Easy to routeand to install in tight areas.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Characteristics: Alternative to spiral hoses in high pressure lines whereflexibility is required. M6K hose is compatible with biodegradable hydraulicfluids like synthetic esters, polyglycols and vegetable oils as well aspetroleum-based fluids.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4M6K0461/414.7600042024000168050HIGH PRESSURE HOSEJ2ATTWO WIRE BRAID JACK HOSEBRAIDED WIRE REINFORCED JACK HOSE•Due to manufacturing tolerances, the external dimension is an average.•Static (non-impulse) pressure rating for hydraulic jack applications only.•Recommended for: Hydraulic jack applications. Meets Material HandlingInstitute specification IJ 100 for hydraulic hose and assemblies used withjacking systems.•Internal tube: Nitrile based.•Reinforcement: Two braids of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +49°C constant.•Standards: Gates proprietary.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4J2AT0461/415.0100006902000013801006J2AT06103/818.810000690200001380130

73PRODUCT CATALOGUE 20213-23HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.MEDIUM PRESSURE HOSEG1ONE WIRE BRAID HOSEBRAIDED WIRE REINFORCED HOSE - SAE 100R1 Type AT•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Medium pressure hydraulic applications.•Internal tube: Nitrile based.•Reinforcement: One braid of high tensile steel wire.•External cover: NBR/PVC based. MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: SAE 100R1AT. SAE 100R1S. EN 853 1SN. ISO 1436.•Characteristics: G1 hose is compatible with biodegradable hydraulic fluidslike synthetic esters, polyglycols and vegetable oils as well as petroleum-based fluids.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3G10353/1611.936252501450010001004G10461/413.53275225131009001005G10585/1615.03125215125008601106G106103/817.52600180104007201308G108121/220.82325160930064018010G110165/823.91900130760052020012G112193/427.91525105610042024016G11625135.8127590510036030020G120311.1/443.492563370025242024G124381.1/249.872550290020051032G13251264600402400168635MEDIUM PRESSURE HOSEACPHIGH TEMP. OIL/AIR RETURNBRAIDED WIRE REINFORCED HOSE - FABRIC COVER•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Multi-purpose, high pressure hydraulic, air compressorlines, petroleum base or phosphate ester hydraulic fluid supply lines. Easyto route and to install in tight areas.•Internal tube: Black, oil resistant synthetic CPE rubber.•Reinforcement: Two braids of high tensile steel wire.•External cover: Blue, oil and abrasion resistant, polyester braid.•Temperature range: -40°C to +149°C.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)24ACP24381.1/254.11500105600042050832ACP3251266.31300905200360635

74PRODUCT CATALOGUE 20213-24HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.MEDIUM PRESSURE HOSEACRHIGH TEMP. OIL/AIR RETURNBRAIDED WIRE REINFORCED HOSE - FABRIC COVER•Due to manufacturing tolerances, the external dimension is an average.•For -24 and 32 sizes please see alternative ACP series.•Recommended for: Pressurised hot oil return lines and air compressorlines, power steering, tilt cab cylinders, engine and transmission coolantand filtration lines.•Internal tube: CPE based.•Reinforcement: One braid of high tensile steel wire.•External cover: Oil resistant textile braid, impregnated with syntheticrubber. MSHA approved.•Temperature range: -40°C to +150°C. Phosphate ester fluids: -40°C to+100°C.•Air: -40°C to +121°C.•Vacuum range: To 30In.Hg (760mm.Hg)•Standards: Gates proprietary. Meets the requirements of SAE J1019performance specifications for use in high temperature transmission oilsystems and high temperature lubrication oil systems using petroleumbased oils.•Characteristics: Very good resistance to weathering and ozone. ACR hoseis compatible with a variety of fluids such as hydraulic oil, phosphateesters.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)24ACR50024381.1/249.550035200014038032ACR5003251263.050035200014046040ACR50040632.1/275.450035200014056048ACR5004876388.9500352000140610WATER JETTINGPCPOWERCLEAN™ WIRE BRAID HOSEBRAIDED WIRE REINFORCED WATERBLAST HOSE•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Hot and cold water high pressure cleaning equipmentwhere heavy duty service is required. Specially compounded cover tohandle pressure washer environment.•Internal tube: Black nitrile.•Reinforcement: Braided high tensile steel wire.•External cover: Nitrile and PVC - non marking.•Temperature range: -40°C to +121°C.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4PC35000461/413.5350024014000900646PC300006103/817.23000210120008401276PC500006103/818.85000350200001320127

75PRODUCT CATALOGUE 20213-25HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.LOW PRESSURE HOSELOLPUSH-LOCK FIBRE BRAID HOSEBRAIDED FIBRE REINFORCED HOSE•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Petroleum-based hydraulic oils, antifreeze solutions,water, hot lubricating oils and air. Suitable for low-pressure cleaning andpneumatic systems, return lines and low pressure lines. Push-Lock hoseand couplings are not recommended for pressure surge applications orcritical applications.•Internal tube: Nitrile based.•Reinforcement: One fibre braid.•External cover: Oil and abrasion resistant synthetic rubber (blendednitrile). MSHA approved.•Temperature range: -40°C to +100°C constant and +121°C intermittent.•Standards: Gates proprietary.•Characteristics: Available in 6 colours for easy colour coding. Easy toassemble.•Suffix A = black, B = blue, C = grey, G = green, R = red, Y = yellow.Please note some size/colour combinations are not held in inventory andare subject to minimum order requirements.Part NumberColourInternalSizeInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3LOLABlack033/1610.430021120084754LOLABlack041/411.930021120084755LOLABlack055/1614.030021120084756LOLABlack063/815.930021120084758LOLABlack081/219.63002112008413010LOLABlack105/823.93002112008415012LOLABlack123/426.930021120084180LOW PRESSURE HOSELOCPUSH-LOCK FIBRE BRAID HOSEBRAIDED FIBRE REINFORCED HOSE•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Petroleum based hydraulic oils, glycol anti-freezecompounds, water, engine lubricating oils and air.•Standards: Meets SAE R2, SAE30 R6, SAE 30R7 performancerequirements for fuel and B20 biodiesel fuel transfer applications.•Internal tube: Black oil resistant synthetic nitrile.•Reinforcement: Single fibre braid.•External cover: Oil and mildew resistant, textile braid, impregnated withsynthetic rubber.•Temperature range: -40°C to +121°C. For air,-40°C to 71°C.Part NumberInternalSizeColourInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4LOC04Black1/413.230021120084756LOC06Black3/816.330021120084758LOC08Black1/220.33002112008413010LOC10Black5/822.930021120084150

76PRODUCT CATALOGUE 20213-26HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.Part NumberInternalSizeColourInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)12LOC12Black3/425.430021120084180

77PRODUCT CATALOGUE 20213-27HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.LOW PRESSURE HOSEGTHPUSH-LOCK FIBRE BRAID HOSEBRAIDED FIBRE REINFORCED HOSE - SAE 100R6•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Hydraulic oil lines, heavy-duty transmission oil coolerlines and glycol anti-freeze solutions. Push-Lock hose and couplings arenot recommended for pressure surge applications or critical applications.•Internal tube: Nitrile based.•Reinforcement: One fibre braid.•External cover: Black - Neoprene based.•Temperature range: -40°C to +135°C constant and +149°C intermittent.•Vacuum range: -3, -4, -5, -6: 28In.Hg (710mm.Hg). -8: 18In.Hg(450mm.Hg). -10, -12: 15In.Hg (380mm.Hg). -16: 10In.Hg (250mm.Hg)•Standards: Gates proprietary. Meets or exceeds requirements of SAE100R6.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3GTH0353/1611.2500352000140504GTH0461/412.7400301600120655GTH0585/1614.2400301600120756GTH06103/816.0400301600120758GTH08121/219.840030160012010010GTH10165/823.135025140010013012GTH12193/426.930020120080150

78PRODUCT CATALOGUE 20213-28HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.LOW PRESSURE HOSEGMV-MEGAFLEXMultiMaster® RETURN AND SUCTIONFIBRE AND WIRE REINFORCED HOSE - SAE 100R4•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Petroleum and water based hydraulic fluids in suctionlines or in low pressure return lines.•Internal tube: Nitrile based.•Reinforcement: Synthetic high tensile steel wire helix.•External cover: Black corrugated chloroprene. MSHA approved.•Temperature range: -40°C to +135°C constant and +150°C intermittent.•Vacuum range: to 25In.Hg (635mm.Hg) for all sizes.•Standards: Gates proprietary. SAE 100R4.•Characteristics: Extremely flexible and lightweight.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)12GMV-MEGAFLEX12193/430.53502414009620.316GMV-MEGAFLEX1625135.83002112008425.420GMV-MEGAFLEX20311.1/442.22501710006833.024GMV-MEGAFLEX24381.1/248.3160116404438.132GMV-MEGAFLEX3251260.7150106004050.840GMV-MEGAFLEX40632.1/274.7150106004063.548GMV-MEGAFLEX4876387.4150106004076.264GMV-MEGAFLEX641024166.41501060040152.4LOW PRESSURE HOSERWPS09MAXIMUS PETROLEUM SUCTIONRUBBER OIL SUCTION - 150 PSI•Conforming Standards: AS2683 Type 1; Grade 2; Kind 1•Temperature: -20°C to +80°C•Cover: Black; Smooth Wrapped Finish SBR Rubber•Tube: Black; NBR Rubber Compound•Reinforcement: High Strength Synthetic Cord Plus Embedded Steel HelixWire•Application: Lightweight Suction Hose for the transfer of petroleumproducts with an aromatic content up to 30%. Resistant to Abrasion AndWeather.Part NumberHose I.D (mm)Hose O.D (mm)WorkingPressure (psi)Workingpressure (bar)Min burstpressure (psi)Min burstpressure (bar)RWPS09-06363.57615010.445031RWPS09-07676.18915010.445031RWPS09-102101.611815010.445031

79PRODUCT CATALOGUE 20213-29HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.LOW PRESSURE HOSEG3HPUSH-LOCK FIBRE BRAID HOSEBRAIDED FIBRE REINFORCED HOSE - SAE 100R3•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Hydraulic oil lines, anti-freeze solutions, or water.•Standards: Meets or exceeed SAE R3.•Internal tube: Black synthetic nitrile.•Reinforcement: Two fibre braids.•External cover: Oil and abrasion synthetic rubber.•Temperature range: -40°C to +135°C.Part NumberInternalSizeInternalDNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min. bendradius (in)Min bendradius(mm)4G3H0461/414.212508850003523756G3H06103/819.1112579450031641008G3H08121/223.91000704000280512512G3H12193/431.87505230002086150

80PRODUCT CATALOGUE 20213-30HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.FLEET APPLICATION HOSEC5CONE WIRE NOMINAL BORE HOSEBRAIDED WIRE REINFORCED HOSE - SAE 100R5•-Size is based on nominal bore of corresponding tube size.•Due to manufacturing tolerances, external dimension is an average.•Recommended for: Medium pressure hydraulic petroleum-based oil linesin impulse applications, lube oil, air and water in applications such as airbrakes, power steering, turbocharger oil supplies, tilt cab cylinders,transmission coolant and filtration lines. Not recommended for gasoline ordiesel fuel.•Internal tube: -4, -5; Neoprene based. Balance of range: Nitrile based.•Reinforcement: One braid of high tensile steel wire over one braid ofpolyester.•External cover: Black, oil and mildew resistant polyester braid.•Temperature range: Under SAE 100R5 (hydraulic) -40°C to +100°C. All-purpose fleet application (hot lube oil lines) -40°C to +149°C. Air to +71°Conly. Avoid continuous use at maximum temperature concurrent withmaximum working pressures.•Standards: Gates proprietary. Meets or exceeds requirements of SAE100R5 for hydraulic applications).Part NumberInternalSizeInternalDiameter(mm)InternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4C5C0453/1613.2300021012000840755C5C0561/414.7300021012000840856C5C0685/1617.0225015590006201008C5C081013/3219.62000140800056011510C5C10121/223.41750120700048014012C5C12165/827.41500105600042016516C5C16227/831.280055320022019020C5C20281.1/838.162545250018023024C5C24351.3/844.550035200014027032C5C32461.13/1656.435024140096340

81PRODUCT CATALOGUE 20213-31HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.FLEET APPLICATION HOSEC5DONE WIRE NOMINAL BORE HOSEMULTI-FLUID BRAIDED WIRE REINFORCED HOSE•-Size is based on nominal bore of corresponding tube size.•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Petroleum-base or phosphate ester fluids; diesel fuelsand filtration lines, transmission coolant lines, hot lube oil lines, powersteering (CAUTION: Intended for heavy-duty commercial vehicle useonly), gasoline and turbocharger oil supplies. Tilt cab cylinder and airbrakes.•Internal tube: CPE based.•Reinforcement: One braid of high tensile steel wire over one braid ofpolyester.•External cover: Green for easy identification, oil and mildew resistant,polyester braid impregnated with synthetic rubber.•Temperature range: -40°C to +149°C. Air to +121°C only.Maximumphosphate esters to +100°C.•Standards: Gates proprietary. Sizes -4 to -12 meet or exceed DOTFMVSS 106-74 Type AII, SAE J1402 Type AII and SAE J1019 and fuelresistance of SAE J30R2.•Special item - please contact Hydraulink for further details and availability.Part NumberInternalSizeInternalDiameter(mm)InternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4C5D0453/1613.215001056000420255C5D0561/414.715001056000420406C5D0685/1617.015001056000420458C5D081013/3219.612508550003405010C5D10121/223.412508550003405012C5D12165/827.47505230002085816C5D16227/831.240028160011289

82PRODUCT CATALOGUE 20213-32HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.FLEET APPLICATION HOSEC5EONE WIRE NOMINAL BORE HOSEHIGH TEMP. BRAIDED WIRE REINFORCED HOSE•-Size is based on nominal bore of corresponding tube size.•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Air brake hose, power steering (for heavy dutycommercial vehicle use only), engine and transmission coolant lines, andhot lube oil lines. Not recommended for gasoline or diesel fuel.•Internal tube: Black, oil and heat resistant synthetic nitrile rubber.•Reinforcement: One braid of high tensile steel wire over one braid ofpolyester.•External cover: Black, oil and heat resistant, textile braid impregnated withsynthetic rubber.•Temperature range: -40°C to +149°C. Air to +121°C only.•Standards: Gates proprietary. Sizes -4 to -12 meet or exceed DOTFMVSS 106, SAE J1402 Type A1.Part NumberInternalSizeInternalDiameter(mm)InternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4C5E0453/1612.415001056000420205C5E0561/41415001056000420256C5E0685/1615.515001056000420358C5E081013/3218.512508550003404510C5E10121/221.112508550003406012C5E12165/824.17505230002087016C5E16227/830.54002816001129020C5E20281.1/837.930021120084115

83PRODUCT CATALOGUE 20213-33HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.FLEET APPLICATION HOSEC5MONE WIRE NOMINAL BORE HOSEMARINE FUEL BRAIDED WIRE REINFORCED HOSE•-Size is based on nominal bore of corresponding tube size.•Due to manufacturing tolerances, the external dimension is an average.•Reference SAE J1942/-1 for USCG-approved working pressures.•Recommended for: On-shore/off-shore and marine diesel fuel andgasoline applications, and hot oil lines up to 100°C.•Internal tube: Nitrile based.•Reinforcement: One braid of high tensile steel wire.•External cover: NBR/PVC based. Blue.•Temperature range: -20°C to +100°C.•Standards: Gates proprietary. Meets marine fuel line specifications SAEJ1527 Type A Class I and SAE J1942 requirements. Exceedsperformance requirements of SAE J30R2 for non-marine applications.Part NumberInternalSizeInternalDiameter(mm)InternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)5C5M0561/414.7500352000140256C5M0685/1617.0500352000140328C5M081013/3219.65003520001404510C5M10121/223.45003520001406012C5M12165/827.45003520001407016C5M16227/831.250035200014090FLEET APPLICATION HOSEPS188POWER STEERING HOSEBRAIDED FIBRE HOSE FOR POWER STEERING•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Power steering pressure lines.•Internal tube: CSM based.•Reinforcement: Two high strength nylon braids that resist hightemperatures and allow for expansion for system noise dampening.•External cover: CSM based.•Temperature range: -40°C to +150°C. Standards: Gates proprietary.Designed to meet requirements of SAE J2050 specifications.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)6PS18806103/818.01500105600042085

84PRODUCT CATALOGUE 20213-34HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.PTFE HOSER14STAINLESS BRAIDED PTFE HOSEPTFE HOSE WITH STAINLESS STEEL BRAIDED COVER•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Air compressor discharge, hot oil fluids, hot andgreasy environments.•Internal tube: Non-conductive white, smooth bore Teflon®/PTFE.•Reinforcement.•External cover: AISI 304/S15 or BS970-1 1996 quality hard drawn tensilestainless steel wire.•Temperature range: -54°C to +204°C. Characteristics: The PTFE hosetube is virtually inert to all chemicals and solvents. It is resistant to fumingSulphuric and Nitric Acids, Amines, Antioxidants and Methanol. It is onlyknown to react with elemental alkali metals (molten or in solution), Fluorineand Chlorine Trifluoride.•NOTE: A damaging electrostatic charge can build up inside the hose whenelectrically resistive fluids are being transmitted at very high flow rates(particularly if the hose assemblies are lengthy).Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)R14-030353/167.940002751200082550R14-040461/49.353250224975067276R14-050585/1611.331602189500655102R14-0606103/812.6526601838000552127R14-0808121/216.5523301617000483152R14-1010165/819.7516601145000345178R14-1212193/422.9615001034500310203R14-161625127.81000693495241310THERMOPLASTIC HOSER7FIBRE BRAID THERMOPLASTIC HOSEBRAIDED FIBRE REINFORCED HOSE - SAE 100R7•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Medium pressure hydraulic applications requiringincreased resistance to abrasion.•Internal tube: Polyester elastomer.•Reinforcement: One or two braids of synthetic fiber. External cover:Abrasion resistant polyurethane, black, pinpricked, white ink-jet branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 100R7.•Characteristics: R7 is a medium pressure hose for use with petroleum,synthetic or water based hydraulic fluids. Suitable for general fluid powertransmission like earthmoving, agricultural machinery and forklift trucks.Also suitable for many industrial gases (check for compatibility).Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3R70353/169.6300021012000840254R70461/412.2300021012000840355R70585/1614.327001901080076045

85PRODUCT CATALOGUE 20213-35HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)6R706103/816.023001609200640558R708121/220.3200014080005607512R712193/427.11300905200360140

86PRODUCT CATALOGUE 20213-36HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.THERMOPLASTIC HOSER7NCFIBRE BRAID THERMOPLASTIC HOSENON-CONDUCTIVE FIBRE REINFORCED HOSE - SAE100R7•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Medium pressure hydraulic applications requiringincreased resistance to abrasion and electrical non-conductivity.•Internal tube: Polyester elastomer.•Reinforcement: One or two braids of synthetic fiber. External cover:Abrasion resistant polyurethane, orange, non pinpricked, black ink-jetbranding branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 100R7.•Characteristics: R7NC is a medium pressure hose for use with petroleum,synthetic or water based hydraulic fluids in applications requiring highelectrical insulation or non-conductivity; e.g. High voltage equipment,safety and rescue equipment, Aerial platforms, Cranes.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3R7NC0353/169.6300021012000840254R7NC0461/412.2300021012000840355R7NC0585/1614.3270019010800760456R7NC06103/816.023001609200640558R7NC08121/220.3200014080005607512R7NC12193/427.11300905200360140THERMOPLASTIC HOSER7TTWINLINE THERMOPLASTIC HOSEBRAIDED FIBRE REINFORCED HOSE - SAE 100R7•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Medium pressure hydraulic applications requiringincreased resistance to abrasion.•Internal tube: Polyester elastomer.•Reinforcement: One or two braids of synthetic fiber.•External cover: Abrasion resistant polyurethane, black, pinpricked, whiteink-jet branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 100R7.•Characteristics: R7 is a medium pressure hose for use with petroleum,synthetic or water based hydraulic fluids. Suitable for general fluid powertransmission like earthmoving, agricultural machinery and forklift trucks.Also suitable for many industrial gases (check for compatibility).•Please note customised multi-line combinations of different hose types ordiameters can also be produced to customer requirements.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4R7T0461/412.2300021012000840355R7T0585/1614.3270019010800760456R7T06103/816.02300160920064055

87PRODUCT CATALOGUE 20213-37HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)8R7T08121/220.3200014080005607512R7T12193/427.11300905200360140

88PRODUCT CATALOGUE 20213-38HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.THERMOPLASTIC HOSER8XFIBRE BRAID THERMOPLASTIC HOSEBRAIDED FIBRE REINFORCED SLIMLINE HOSE - SAE100R8•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications requiringincreased resistance to abrasion.•Internal tube: Polyester elastomer.•Reinforcement: One or two braids of aramid fiber.•External cover: Abrasion resistant polyurethane, black, pinpricked, whiteink-jet branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 100R8.•Characteristics: R8X is a compact high pressure hose for use withpetroleum, synthetic or water based hydraulic fluids. Suitable for generalfluid power transmission like earthmoving, agricultural machinery andforklift trucks. Also suitable for many industrial gases (check forcompatibility).Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)2R8X0241/886000420240001680253R8X0353/168.95000350200001400304R8X0461/411.55000350200001400505R8X0585/1613.44300300172001200556R8X06103/815.54000280160001120608R8X08121/219.93500245140009808012R8X12193/426.923001659200660150THERMOPLASTIC HOSER8XNCFIBRE BRAID THERMOPLASTIC HOSENON-CONDUCTIVE FIBRE REINFORCED HOSE - SAE100R8•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications requiringincreased resistance to abrasion and electrical non-conductivity.•Internal tube: Polyester elastomer.•Reinforcement: One or two braids of aramid fiber.•External cover: Abrasion resistant polyurethane, orange, non-pinpricked,black ink-jet branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 100R8.•Characteristics: R8XNC is a compact high pressure hose for use withpetroleum, synthetic or water based hydraulic fluids in applicationsrequiring high electrical insulation or non-conductivity; e.g. High voltageequipment, Safety and rescue equipment, Aerial platforms, Cranes.•Special item - please contact Hydraulink for further details and availability.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4R8XNC0461/411.5500035020000140050

89PRODUCT CATALOGUE 20213-39HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)5R8XNC0585/1613.44300300172001200556R8XNC06103/815.54000280160001120608R8XNC08121/219.935002451400098080

90PRODUCT CATALOGUE 20213-40HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.THERMOPLASTIC HOSER8XTTWINLINE THERMOPLASTIC HOSEBRAIDED FIBRE REINFORCED SLIMLINE HOSE - SAE100R8•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: High pressure hydraulic applications requiringincreased resistance to abrasion.•Internal tube: Polyester elastomer.•Reinforcement: One or two braids of aramid fiber.•External cover: Abrasion resistant polyurethane, black, pinpricked, whiteink-jet branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 100R8.•Characteristics: R8X is a compact high pressure hose for use withpetroleum, synthetic or water based hydraulic fluids. Suitable for generalfluid power transmission like earthmoving, agricultural machinery andforklift trucks. Also suitable for many industrial gases (check forcompatibility).•Please note customised multi-line combinations of different hose types ordiameters can also be produced to customer requirements.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4R8XT0461/411.55000350200001400506R8XT06103/815.54000280160001120608R8XT08121/219.935002451400098080THERMOPLASTIC HOSER18FIBRE BRAID THERMOPLASTIC HOSELOW TEMP. FIBRE REINFORCED HOSE - SAE 100R18•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Medium pressure hydraulic applications exposed tolow temperatures, or cyclic and quick temperature changes, such as cool-stores.•Internal tube: Polyester elastomer.•Reinforcement: -03; one braid of synthetic fibre. Balance of range; twobraids of synthetic fiber.•External cover: Special polyester for low temperature, black, pinpricked,white ink-jet branding.•Temperature range: -55 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 10018.•Characteristics: R18 is a medium pressure hose suitable for petroleum orsynthetic based hydraulic fluids in hydraulic systems of forklifts. Optimumbonding characteristics and special cover also make it an ideal forequipment operating in cold environments, while maintaining a high levelof flexibility.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4R180461/412.2300021012000840355R180585/1614.3300021012000840456R1806103/816.630002101200084045

91PRODUCT CATALOGUE 20213-41HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)8R1808121/222.53000210120008407010R1810165/826.1300021012000840100

92PRODUCT CATALOGUE 20213-42HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.THERMOPLASTIC HOSER18TTWINLINE THERMOPLASTIC HOSEBRAIDED FIBRE REINFORCED HOSE - SAE 100R18•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Medium pressure hydraulic applications exposed tolow temperatures, or cyclic and quick temperature changes, such as cool-stores.•Internal tube: Polyester elastomer.•Reinforcement: -03; one braid of synthetic fibre. Balance of range; twobraids of synthetic fiber.•External cover: Special polyester for low temperature, black, pinpricked,white ink-jet branding.•Temperature range: -55 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Standards: Meets or exceeds SAE 10018.•Characteristics: R18 is a medium pressure hose suitable for petroleum orsynthetic based hydraulic fluids in hydraulic systems of forklifts. Optimumbonding characteristics and special cover also make it an ideal forequipment operating in cold environments, while maintaining a high levelof flexibility.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4R18T0461/412.2300021012000840355R18T0585/1614.3300021012000840456R18T06103/816.6300021012000840458R18T08121/222.53000210120008407010R18T10165/826.1300021012000840100PAINTSPRAY HOSEPS1BONE WIRE BRAID THERMOPLASTICBRAIDED WIRE REINFORCED HOSE FORPAINT/SOLVENTS•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Airless paint spray systems or applications requiringhigh chemical resistance to solvents and aggressive fluids.•Internal tube: Polyamide PA6.•Reinforcement: One braid of high tensile steel wire.•External cover: Polyurethane, blue, non-pinpricked, black ink-jet branding.•Temperature range: -40 °C to +100 °C, limited to +70 °C for air and water-based fluids.•Characteristics: PS1B is a high pressure hose with blue cover, particularlydesigned for paint spray and solvent applications with increasedresistance to abrasion, mechanical strength and providing electricalconductivity. Due to low dissipation rate of tube, the hose is also suitablefor many industrial gases (check for compatibility).Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)4PS1B0461/411.6440031012000840406PS1B06103/815.532002251280090065

93PRODUCT CATALOGUE 20213-43HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.AUTOMOTIVE HOSELPGLPG SERVICE HOSEWIRE AND FIBRE REINFORCED HOSE FOR LPG•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: LPG service line for mobile plant, particularly forklifttrucks.•Internal tube: Synthetic rubber, LP Gas, oil and low temp resistant.•Reinforcement: One textile and one stainless wire braid.•External cover: Textile braid.•Standards: Meets AS/NZ 1869 Class D, AGA Certificate no. AGA5318Part NumberInternalSizeInternalDiameter(mm)InternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)5LPG0585/1617.135024140096AUTOMOTIVE HOSEMVAPLPG VAPORISER HOSEUNREINFORCED VAPORISER HOSE FOR LPG•Due to manufacturing tolerances, the external dimension is an average.•the 18mm ID will clamp down to suit 5/8, or stretch over 3/4.•Recommended for: High temperature gas transportation hose up to+125C.•Internal tube: Synthetic rubber, LP Gas resistant.•Reinforcement: n/a•External cover: Textile braid.Part NumberInternalSizeInternalDiameter(mm)InternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)18MVAP10-12185/8-3/425.4110844032

94PRODUCT CATALOGUE 20213-44HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.AUTOMOTIVE HOSE27000FUELFUEL LINEFUEL LINE SAE 30R6 AND 30R7•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Use on fuel lines, PCV and EEC systems, and for fuelreturn hose connections on diesel fuel injection systems.•Approved for use with leaded and unleaded petrol, diesel, methanol, andethers.•Internal tube: Nitrile.•Reinforcement: Spiral reinforced construction.•External cover: Oil resistant NBR/PVC cover.•Temperature: -40°C to 125°C with gasoline blends.•Standards: Meets SAE 30R6 and 30R7.Part NumberInternal SizeInternal Diameter(mm)Working Pressure(psi)Working pressure(bar)270001/83.2504270013/164.8504270021/46.3504270035/168504270043/89.5504270057/1611.1352.4270061/212.7352.4270085/815.9352.4270103/419352.4AUTOMOTIVE HOSE27000VACVACUUM HOSEVACUUM HOSE•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Windshield washers, vacuum operated accessories,and radiator overflow.•Vacuum rated to 24in/Hg.•Temperature: -40°C to 125°C•Standards: Meets SAE J1037, J942b specifications.Part NumberInternal SizeInternalDiameter (mm)InternalDiameter (in)ExternalDiameter (mm)Suction (In. Hg)Suction (mmHg)270425/3240.164.824610270437/3260.2210.724610270417/6430.115.624610270505/1680.3112.724610270441/460.2511.424610270533/8100.3815.924610

95PRODUCT CATALOGUE 20213-45HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.FIRE SUPPRESSION HOSERFSONE WIRE BRAID HOSERED FIRE SUPPRESSANT BRAIDED WIRE REINFORCEDHOSE - SAE 100R1 Type AT•Due to manufacturing tolerances, the external dimension is an average.•Recommended for: Low pressure powder fire suppressant applications inmining, forestry and firefighting equipment.•Internal tube: Black, oil and heat resistant synthetic nitrile rubber.•Reinforcement: One braid of high tensile steel wire.•External cover: Red, oil and abrasion resistant nitrile and PVC.•Temperature range: -40°C to +100°C.•Standards: Meets performance requirements of SAE 100R1.Part NumberInternalSizeInternal DNInternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min bendradius(mm)3RFS0353/1611.4300020512000820754RFS0461/413.52750190110007601006RFS06103/817.3225015590006201308RFS08121/220.32000140800056018012RFS12193/427.71250855000340240MULTIPURPOSE HOSEPREMOFLEXPremoflex MULTI-PURPOSE HOSETWO YARN SPIRAL REINFORCED INDUSTRIAL HOSE•Recommended for: Premo Flex is the perfect choice for multipleapplications requiring a highly flexible and cost-effective hose withmaximum resistance to petroleum oils/kerosene/fuel oil (to 120°F) andlubricating oils (to 212°F). Premo Flex can be used for transferringgasoline or diesel fuels. It is also suitable for air and water applications; Itoffers excellent weather and ozone resistance and is nonconductive at1000 volts D.C.•Temperature range: -40°F to +212°F(-40°C to +100°C) continuous service.•Tube: Type C (Nitrile). Black. RMA (Class A) high oil resistance.•Reinforcement: Synthetic high tensile cord.•Cover: Type C2 (Modified Nitrile). Red (black cover available on specialorder). All sizes thru 1/2 are perforated. RMA(Class B) medium oilresistance.Part NumberInternalSizeInternalSize (mm)ExternalDiameter(in)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Min burstpressure(bar)Min. bendradius (in)Min bendradius(mm)PREMOFLEX-04046.4.512.72501775052250PREMOFLEX-06069.5.6616.82501775052375PREMOFLEX-080812.7.8521.625017750524100PREMOFLEX-101015.8125.425017750525130PREMOFLEX-121219.11.1529.225017750525130PREMOFLEX-161625.41.4737.325017750528205

96PRODUCT CATALOGUE 20213-46HYDRAULIC HOSE† - Please contact Hydraulink for further details and availability.Pricing current as at 6 Dec 2020 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.MULTIPURPOSE HOSETERMINATORTerminator MULTI-PURPOSE HOSECORD REINFORCED INDUSTRIAL HOSE•Recommended for: Terminator is one tough hose with a rugged cover foroutstanding abrasion resistant capability and extended service life whereconstant flexing and bending is required. This top-of-the-line industrial andoil-resistant hose is designed for applications involving air/oil/watertransfer as well as grease sprays/paraffin waxes/salt solutions and avariety of chemicals. It offers excellent durability for extra long life inmining/air drill/construction/poultry plants/quarries/shipyards/foodprocessing/ railroads and other severe service environments. Excellentindustrial hose with weather and ozone resistance; Nonconductive at 1000volts D.C.•Temperature range:-40°F to +212°F (-40°C to +100°C) continuous service.•Tube: Type C (Nitrile) hose. Black. RMA (Class A) high oil resistance.•Reinforcement: Synthetic high tensile cord.•Cover: Type C4 (Carboxylated Nitrile). Yellow. RMA (Class A) high oilresistance.Part NumberInternal Size Internal Size(mm)ExternalDiameter(mm)WorkingPressure(psi)Workingpressure(bar)Min burstpressure(psi)Max suctionpressure -(mm Hg)Min bendradius (mm)TERMINATOR-04046.414.55013575076276TERMINATOR-06069.519.15013575063576TERMINATOR-080812.722.650135750635127TERMINATOR-121219.1315013530381152TERMINATOR-161625.438.45013530254203

97PRODUCT CATALOGUE 202011PRODUCT CATALOGUE 2019SWAGE COUPLINGSSECTION 4

98PRODUCT CATALOGUE 20214 - 1www.hydraulink.com1002SROTCENNOC D IULFK N I LUARDYH© t hg i r ypoCwww.hydraPAGENERAL INFORMATIONINFORMATION - SWAGE HOSETAILSTheber ModModModModThe Hydraulink range of hose couplings are available in three main series; Swage, Field Attachable (often referred to as reusable) and Push-on.The swage series hosetail is designed as a combination tail suitable for use with all hose types from multi-spiral wire to bre-reinforced thermoplastic. Simply select the ferrule type to match the relevant hose. Please note that Hydraulink swage hosetails should only be used with the ferrules listed in section four of this catalogue.Hydraulink thread forms and sealing methods are manufactured to the relevant international stan-dards where applicable. All dimensions shown are nominal, and subject to change due to ongoing product development. For critical applications, please contact Hydraulink to con rm dimensions.Hydraulink swage hosetails are typically manufactured from high quality steel and nished with a silver trivalent chromium plating and clear sealant to further increase protection against corrosion.Other material types (such as AISI 316 stainless steel) and nishes are available on request.Hydraulink Fluid Connectors Ltd. reserves the right to discontinue, or to alter the design and speci -cation of any product listed in this catalogue.Our product range is constantly evolving and Hydraulink reserve the right to change technical specifications without notice

99PRODUCT CATALOGUE 2021aulink.com1002SROTCENNOC D IULFK N I LUARDYH© t hg i r ypoCART NUMBERING SYSTEM – STEEL SWAGE COUPLINGSINFORMATION - SWAGE HOSETAILS03e Hydraulink part numbering system is a concise product description in coded form. The part num-The Hydraulink part numbering system is a concise product description in coded form. The part num- consists of four modules as follows:ber consists of four modules as follows:dule 1. Pre x letter; Module 1. denotes coupling type.S = Swage R = Field Attachable (Reusable) = Field Attachable (Reusable) P = Push-on R5 = Field Attachable (Reusable) to suit SAE 100R5 hose Attachable (Reusable) to suit SAE 100R5 hose SU = Suction tail.dule 2. Series Code;Module 2. denotes the thread form or sealing method (coupling end) and the denotes the thread form or sealing method (coupling end) and thecon guration of the hosetail. E.g.; series code #51 denotes a BSPP swivel nut female in a swept 90° con guration, swivel nut female in a swept 90° con guration,series code #29 denotes a JIC female swivel nut in a compact 90° con guration.series code #29 denotes a JIC female swivel nut in a compact 90° con guration.Series codes may also have a suf x, denoting further information about the coupling.x, denoting further information about the coupling.Please refer to the following “Series Codes and Descriptions” for further informationPlease refer to the following “Series Codes and Descriptions” for further informationregarding coupling ends and con gurations.regarding coupling ends and con gurations.dule 3. Coupling end size; Module 3. denotes the size of the thread form or sealing method of thedenotes the size of the thread form or sealing method of thehosetail. Sizes are expressed as follows;hosetail. Sizes are expressed as follows;English/American threads; expressed in 1/16th inch increments denoting the key diameter. English/American threads; expressed in 1/16th inch increments denoting the key diameter. For example; 08 = 8/16 = 1/2” and 19 = 19/16 = 1 3/16”.For example; 08 = 8/16 = 1/2” and 19 = 19/16 = 1 3/16”.Metric threads; expressed in millimetres with pre x M, denoting the key diameter. x M, denoting the key diameter. For example; M10 = 10mm O.D. thread.For example; M10 = 10mm O.D. thread.Flanges; express the nominal size of the ange head. Nominal sizing refers to the maximumange head. Nominal sizing refers to the maximum internal bore. For example a 12 ange head would have a maximum internal bore of 12/16 = 3/4”.ange head would have a maximum internal bore of 12/16 = 3/4”.Please refer technical section for further information regarding coupling ends, thread formsPlease refer technical section for further information regarding coupling ends, thread formsand sealing methods.dule 4. Hosetail outside diameter; Hosetail outside diameter; denotes both the nominal O.D. of the hosetail and the I.D denotes both the nominal O.D. of the hosetail and the I.Dof the hose it would suit. Sizes are expressed in 1/16th inch increments.of the hose it would suit. Sizes are expressed in 1/16th inch increments.For example; 06 = 6/16 = 3/8” and 20 = 20/16 = 1 1/4”.For example; 06 = 6/16 = 3/8” and 20 = 20/16 = 1 1/4”.le om vant g i -4 - 21002SROTwww.hydraulink.com1002SROTCENNOC D IULFK N I LUARDYH© t hg i r ypoCPART NUMBERING SYSTEM – STEEL SWAGE COUPLINGSINFORMATION - SWAGE HOSETAILSPre x letter; denotes coupling type.S = Swage FP = Push-on R5 = Field SU = Suction tail. Series Code;con guration of the hosetail. E.g.; series code #51 denotes a BSPPSeries codes may also have a sufCoupling end size; Metric threads; expressed in millimetres with preFlanges; express the nominal size of the internal bore. For example a 12 and sealing methods.Module 4. Our product range is constantly evolving and Hydraulink reserve the right to change technical specifications without notice

100PRODUCT CATALOGUE 20214 - 3www.hydraulink.com1002SROTCENNOC D IULFK N I LUARDYH© t hg i r ypoCwww.hydraSEPART NUMBERING SYSTEM - EXAMPLESINFORMATION - SWAGE HOSETAILSCODE0102030405060708091011110121313R133135141516171819202122225226232362425262728293031323334353637383939N39F40S40N41424344454564646546647484950Part number: S05H-1208Complete desription: 3/4” JIC swivel nut female x 1/2” hose tail, straight swage coupling with back hex.Part number: S51-0808Complete desription: 1/2” BSPP swivel nut fe-male x 1/2” hose tail, swept 90° swage coupling.S 05 H - 12 08Module 3. Coupling end size³ ´ IRU WKV ´Module 4. Hosetail O.D.³ ´ IRU WKV ´Module 1. Prefix letter³6´ IRU VZDJHModule 2. Series code³ ´ IRU -,& VZLYHO QXWIHPDOH VWUDLJKW FRXSOLQJSeries code suffix³+´ IRU FRXSOLQJ ZLWK KH[DJRQDO EDFNQXWModule 3. Coupling end size³ ´ IRU WKV ´Module 4. Hosetail O.D.³ ´ IRU WKV ´Module 1. Prefix letter³6´ IRU VZDJHModule 2. Series code³ ´ IRU %633 VZLYHO QXWIHPDOH VZHSW ƒ FRXSOLQJS 51 - 08 08Our product range is constantly evolving and Hydraulink reserve the right to change technical specifications without notice