GS DC Smart Link

Technical Training Technical Training manual GS-Slab Scissors with SmartLink control system GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk

Technical Training Introduction Important Read, understand and obey the safety rules and operating instructions in the appropriate Operator’s Manual on your machine before attempting any maintenance procedure. Basic mechanical, hydraulic and electrical skills are required to perform most procedures. However, several procedures require specialized skills, tools, lifting equipment and a suitable workshop. In these instances, we strongly recommend that maintenance and repair be performed at an authorized Genie dealer service center. This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk

Technical Training Table of Contents 1. Machine introduction & walk around 1.1 GS Slab SmartLink Introduction 1.2 DC SmartLink scissor products familiarization 1.6 GS Slab SmartLink Introduction GS3232 1.15 DC SmartLink scissor products familiarization GS3232 1.16 2. Functionality and specifications 2.1 Elevating 2.2 Drive & steer system 2.4 Pothole 2.5 Manual brake release 2.6 GS3232 PCON controls & outrigger 2.7 Specifications 2.9 Measures and limits example 2.9 Batteries 2.10 Battery charger 2.11 Speed and performance 2.16 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures Fluid capacities, tires and wheels 2.16 3. Hydraulics 3.1 Hydraulic symbols legend 3.1 Manifolds and hydraulic schematic GS1530>GS1932 3.2 Manifolds and hydraulic schematic GS2023>GS3246 3.4 Manifolds and hydraulic schematic GS4047 3.6 Manifolds and hydraulic schematic GS3232 3.8 Hydraulic schematics / Flow to tank 3.10 Steering / drive 3.11 Breaking 3.14 Relief valve / adjustments 3.17 Lift 3.21 Platform down 3.22 Platform with two cylinders 3.23 GS4047 elevating and descending 3.27 GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk

Technical Training 4. Electrics 4.1 Electric symbols legend 4.3 Electrical component legend 4.4 Electric schematic overview 4.5 GCON I/O map 4.6 Power to ground controls 4.10 Model detection 4.11 Elevating from GCON / Motor controller 4.14 Overload System 4.17 Platform controls / Drive from PCON 4.19 Pothole / Outriggers 4.20 Electrical schematics A3 4.22 5. Faults, setup and calibration 5. 1 GCON/ ECM 5.2 Operational Indicators code (OIC) 5.3 Diagnostics trouble code (DTC) 5.4 Type “HXXX” faults 5.5 Type “PXXX” faults 5.8 Type “UXXX” faults 5.9 Type “FXXX” faults 5.11 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures Type “CXXX” faults 5.13 Troubleshooting 5.14 GCON display navigation 5.15 Select model menu 5.16 Select option menu 5.16 Select parameters and service override 5.17 Service override 5.18 Platform overload calibration 5.19 Platform overload calibration 5.19 Platform overload calibration 5.23 6. Software 6.1 GCON setup laptop 6.2 Machine setting parameters 6.4 Machine setting calibration curves 6.6 Diagnostics 6.8 Software 6.9 GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 1 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 2 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 3 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 4 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 5 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 6 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training Components located on the Non-steer end are Manual brake release manifold used to release the parking brakes of the machine for towing. • Caution: Block tires before manually releasing brakes • To release the parking brake you have to push in the Manual brake dump valve handle • Then pump the Manual Hand pump until parking brakes release • Parking brakes will restore to normal operation when drive is activated • Spring applied hydraulic released Parking Brake. • 370psi to 450psi needed to fully release the brakes There is a Auxiliary lowering handle that can be used to lower the machine in case of control system failure. • Non-marking solid rubber Tires. This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 7

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 8 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 9 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training •Tilt level sensor opens @ 1.5 degrees side ways and 3 degrees front to rear • DISABLES LIFT UP AND DRIVE IF THE LINKAGE IS NOT STOWED. *NOTE* TILT ALARM ONLY SOUNDS WHEN OUT OF STOWED •Warning: Tilt level sensor must be installed per instructions in service manual •Down limit switch is forced closed by the linkage when the linkage is stowed. It relaxes and opens when linkage is out of stowed. The ECU disables drive if the pothole arms are not deployed when linkage is not stowed. •Buss connection for components on top of chassis •Control cable quick disconnect allows platform controller to be connected near the chassis. _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 10

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 11 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 12 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 13 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training Scissors products have a 5 conductor control cable that runs from the platform control box This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures to the base control box. These photographs show quick disconnects below the platform and above the chassis. This allows the platform control box to be connected directly to the chassis, bypassing the cable running through the linkage in case the control cable becomes damaged. Note. Be careful because sometimes the colors don’t match with the connector’s IN/OUT, e.g. the green wire in don’t have to be the same line that the another green wire out. _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 14

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 15 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 1. 16 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 1 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GCON and PCON controls is communicate by Can buss system and the motor controller is managed by the GCON This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 2

Technical Training • Platform Up Function Overview • Fixed lift speed when operating from base control This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures • Variable lift speed when operating from platform control (2 speed) • Variable lift speeds are not achieved by hydraulic control valves. The electric motor speed determines the flow based on joystick input. • The lift function is interrupted is when the lift linkage is out of stowed and chassis is out of level • The up function is disabled when the machine is overloaded. • Platform Down Function Overview • Fixed lowering speed from platform and base control • Gravity down speed metered by fixed orifice • Platform down can be operated manually in case of any system failure • The down function is disable when the machine is overloaded. • Functionality • ECM monitors inputs from down limit switch and pothole limit switches. • As the machine is lifted the pothole arms are deployed putting the machine in the elevated drive speed range. • If a pothole arm is blocked with the lift linkage out of stowed the lift function will continue to operate but the drive function will be disabled and an audible alarm will sound. • Tilt alarm is inactive when the lift linkage is stowed. • When the lift linkage is out of stowed and the machine is out of level the tilt alarm sounds, lift is disabled, and drive is disabled. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 3

Technical Training • Drive Function Overview • Drive function can only be performed from the platform controls This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures • Drive speeds are infinitely proportional based on joystick demand • Maximum drive speed is reduced to .75 MPH when lift linkage is out of stowed and pothole arms deployed • Drive is interrupted when lift linkage is out of stowed and either pothole arm has not deployed or the machine is out of level • The drive is cut off when the machine is overloaded • Steer Function Overview • When in drive mode steer always takes priority • Steer speed is fixed at .75GPM by a priority flow regulator • Steer can only be operated from the platform controls and only while in drive mode GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 4

Technical Training • Potholes • As the machine is lifted the pothole arms are deployed putting the machine in This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures the elevated drive speed range. • If a pothole arm is blocked with the lift linkage out of stowed the lift function will continue to operate but the drive function will be disabled and an audible alarm will sound. • Tilt alarm is inactive when the lift linkage is stowed. • When the lift linkage is out of stowed and the machine is out of level the tilt alarm sounds, lift is disabled, and drive is disabled. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 5

Technical Training • Brakes can be released manually to winch the machine onto a truck or to move the machine when it is not operational • The brakes will automatically reset when a drive function is selected preventing This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures accidental run on after they have been manually released GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 6

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 7 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training • Lift function disabled at 6 meters( 2 limit switches in series for redundancy) without outriggers on ground . • Outriggers can only be used in platform mode and when the platform is stowed. This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures • When outriggers are not fully retracted drive is disabled and lift function is restricted. • When outriggers are deployed they must be in contact with the ground and will automatically level unit on slopes of up to 3 degrees front to back and 5 degrees side to side. • There are four Outrigger cylinders located on all four corners of the chassis to stabilize the scissors in order to enable the unit to be raised past 6 meters. • Each Cylinder has a Pressure transducer connected to the outrigger controller to indicate when the cylinder jack has contacted the ground, fully extended, not retracted or fully retracted. These states are captured during the outrigger calibration. • Each cylinder is equipped with a pilot operated check valve to hold the cylinder in the extended position. The check valves are piloted open when retracting the outriggers. • Each cylinder also has a solenoid valve that has to activated to allow oil in or out of the barrel end of the cylinder. • To auto level the machine we utilize a separate Tilt sensor above the normal one to detect the pitch and roll angle GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 8

Technical Training This is an example: always refer to the Service or Operator manual for This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures the right specifications. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2. 9

Technical Training This bateries system provide a power 24V and 225AH with This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures a reserve capacity @ 25A rate 447 minutes because all batteries are connected in series. This battery system provides 24V and 300AH with a reserve capacity @ 25A rate 560 minutes because 2 batteries connected in series (24V 150AH) are connected in parallel with another 2 similar system batteries (24V 150AH) , so in total all batteries provide a power 24V and 300AH. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.10

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.11 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training 1. Determine whether flooded or sealed ( AGM/GEL) type lead acid batteries are being charged. A yellow wire loop at the back of the charger sets the charge curve for either flooded lead acid or AGM/GEL type batteries. The loop is left for flooded batteries; for AGM/GEL cut the loop and tape the wire ends back with electricians tape. 2. Plug the charger into a single phase AC socket with a nominal voltage rating of 100V, 110V, 115V, 120V, 220V, 230V, or 240V and a frequency rating of 50 or 60Hz. The charger automatically senses and adjusts to the AC voltage and frequency. At 110/120V the wall socket circuit breaker should be a 15A breaker with no other loads on the circuit. 3. The charger will start charging the batteries automatically within a few seconds. Even severely discharged batteries will be charged as long as the battery voltage is greater then 4V. If the battery voltage is low when charging first starts charging will be at a lower current level until the battery has recovered enough to accept full charging current. 4. The four LED’s indicate the charging progress. The first (leftmost) yellow (or amber color) LED will light to show there is AC power to the charger. The yellow LED next to the “AC” LED shows the battery is charging. When the battery reaches 100% charged the green LED labeled “100%” will light. When the battery is fully charged the green LED labeled “100%” will light and the yellow LEDs will remain “on”. Charging time is dependent on depth of battery discharge, battery condition, and temperature. The battery can be disconnected after the 100% LED is on or left connected – see 5. If the battery is to be disconnected before charging is complete the AC cord should be unplugged first to avoid sparking. 5. If the charger is left plugged in to the AC socket and the battery is kept connected This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures after charging is complete (100% LED on), the charger goes into maintenance mode to keep batteries charged while in storage. The charger continuously measures battery voltage and restarts the charging cycle if the battery voltage drops too low. This keeps batteries charged while in storage but does not boil-out the electrolyte over time. 6. Turn-off the charger by unplugging (disconnect from AC voltage). GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.12

Technical Training Technical Operation Summary – The charger is an advanced, microprocessor controlled, high frequency switching type charger. The charging curve is an IEI type for flooded and This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures IE type for sealed type lead acid batteries. The IEI curve is constant current, then constant voltage, then constant current at a reduced level. Charging is complete when the battery voltage is rising at a very low rate (dV/dt) showing the battery has accepted all the charging it can. The IE curve is constant current then constant voltage with shut-off when the current reaches a low level. The charger will work even with batteries in a severe discharge state with battery terminal voltages as low as 4V. This reduces the need to “boost charge” weak batteries before charging. The charger has a 24 hour timer in case charging can not be completed due to battery problems – see troubleshooting section for this and other problem information. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.13

Technical Training Troubleshooting: Identify the problem from the following list and refer to the appropriate section for detailed instructions. 1. Charger does not turn on or no yellow “AC” power LED. 2. Red “BAD” LED is on 3. Yellow AC LED is on, yellow DC LED is off (100% and red LEDS are off) 4. Batteries do not fully charge. 5. The AC supply circuit breaker is tripped 1. YELLOW AC LED IS OFF (OTHER LEDS ARE OFF) Double check the outlet to ensure it is working by trying out another known good piece of equipment on the outlet. Check the circuit breaker to see if it has tripped and if it is a 15A rating and that there is no other draw on the circuit. Check the AC plug and wire to ensure both are in good condition. Replace charger if everything else is correct. 2. RED LED IS ON - The faults identified below cause the red LED to go on. ▶ RED LED IS ON, YELLOW AC LED IS ON, YELLOW DC LED IS ON, and GREEN 100% LED IS OFF The charger has been unable to fully (100%) charge the batteries in 24 hours and has timed- out. Unplug the charger, count to ten, and plug charger back in to reset the charge cycle and give the charger another 24 hour timing period. Note that this indicates the battery pack is damaged (one or more weak cells), worn-out, or the charger has been connected to the wrong voltage battery pack (12V or 18V for example) as the charging should be complete before 24 hours. Batteries should be checked including electrolyte level in all cells. If the battery voltage is correct and the problem is a weak battery, the charger will continue to charge the battery pack but the battery pack may provide short operating times and need to be replaced. ▶ RED LED IS ON, YELLOW AC LED IS ON, YELLOW DC LED IS ON, and GREEN 100% LED IS ON The output has completed charging, however, the battery voltage has decreased quickly after the charging was completed, that is, the battery is not holding charge. The machine may be used; however, operating times are likely to be less than normal as this indicates the battery This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures pack is damaged or weak. Check all electrolyte levels and try charging again. If this error continues to show-up the battery pack should be replaced. 3. YELLOW AC LED IS ON, YELLOW DC LED IS OFF (100% AND RED LEDS ARE ALSO OFF) The charger has AC power going to it but is unable to charge the battery. This may be caused by: - open circuit – poor connection to the batteries or a high resistance connection anywhere in the charger + battery circuit. Check the charger connection (terminals) to batteries and if correct (no cut wires, connected to the right pace on the battery pack) remove, clean, and reinstall the charger to battery terminals and the terminals between each battery. The charger is a high- output low resistance system, even if the terminals look OK they might not be good enough to allow proper charging. - reverse polarity connection – if work has been done on the machine and the charger disconnected the + and – terminals of the charger may have been reversed. Correct charger terminal connections – black wire to – of the battery pack, red wire to + (24V) of the battery pack. - short circuit – if the charger wires are connected together (short circuit) this will be displayed. Connect charger wires to the correct locations on the 24V battery pack. - incorrect battery voltage – if the charger were connected to the wrong voltage battery, that is a battery voltage above 24V such as a 36V battery pack, the charger will not operate and will display this code. Connect only to a 24V battery pack. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.14

Technical Training Fault Codes AC DC 100% BAD CONDITION YLW LED GRN LED GRN LED RED LED OFF OFF OFF OFF No AC power to charger Charger has timed-out at 24 hrs – battery pack probabl ON ON OFF ON y bad or a bad cell. Unplug the AC to reset the charger. Charger charging cycle completed, however, the batter y voltage has dropped within ½ hour of charging comp ON ON ON ON leted. Charger is still in maintenance mode. Battery pack probably bad, weak, or a bad cell Output open circuit or reverse polarity connection or s ON OFF X X hort circuit or battery voltage is too high. Correct. 4. BATTERIES DO NOT FULLY CHARGE - If the batteries are charged overnight, make sure the AC supply is not being switched-off at night with other building items. - If batteries are new they sometimes need 20 to 30 charge/discharge cycles before they charge normally due to a process called plate formation. With new batteries the 100% LED may not light after a normal overnight charge. The batteries and charger are fine – the machine should be used and charged each night. Within a few days to a week the 100% LED will go on during a normal overnight charge. Note – brand new batteries are more easily damaged by too heavy a discharge than batteries that are older with formed plates. Try to avoid too heavy a discharge with your customers when new batteries are installed for at least This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures the first 20 charge cycles. - If batteries are old, check the battery condition following the battery supplier’s instructions. Check for dead cells or reduced capacity. If the charger LEDs are showing charging and charger case gets warm after several hours the charger is probably good and the batteries bad. Replace charger only if other problems are not found. 5. THE AC SUPPLY CIRCUIT BREAKER IS TRIPPED An overloaded AC circuit, defective circuit breaker, defective fuse, or a charger problem can cause this condition. First, check the total load on the AC circuit to avoid overload. If total AC load is OK, connect the charger to a different AC outlet (on a different circuit) in the building. If the charger operates properly on other AC outlets, a qualified person should correct the AC circuit problem. If the AC supply checks good, the charger should be replaced. This is very rare. Note: Over 1/2 of all battery chargers returned as 'failed' are good. Please follow the troubleshooting procedures carefully and check all other items before returning the charger as failed. GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.15

Technical Training To see specifications of operator’s manual and service manual according to the model and serial number This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.16

Technical Training To see specifications of operator’s manual and service manual according to the model and serial number This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 2.17

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 1 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 2 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 3 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 4 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 5 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 6 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 7 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 8 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 9 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 10 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 11 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 12 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures

Technical Training GS DC Smart Link Rev.A GS Slab Smart Link 1000 www.genielift.co.uk 3. 13 This training manual and the information contained within is designed to be used as an aid to a service training course. The appropriate Genie Service Manual should always be referred to when carrying out maintenance or repair procedures