YKK-AP-VOL1

Product Selection GuideOPERABLE WINDOWS – PERFORMANCE BY SYSTEMYES SSG Vent Air (ASTM E 283): 0.10 cfm/ft² @ 1.57 psfOutswing vent window for 1\" insulatingglass that provides ventilation for Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixedstorefront applications withoutadding the obtrusive sight line of a AAMA/WDMA Rating: CW-60traditional window. Thermal (AAMA 1503 & CRFf of 59 NFRC 102): U-Value of 0.43 btu/hr/ft²/°F or less ASTM E 90 & ASTM E 1332: 32 STC, 25 OITCYES SSG TU Vent Air (ASTM E 283): 0.10 cfm/ft² @ 6.24 psfThermally broken outswing vent windowfor 1\" insulating glass that provides Water (ASTM E 331, ASTM 12.0 psf Operable, 15 psf Fixedventilation for storefront applicationswithout adding the obtrusive sight line of E 547):a traditional window. AAMA/WDMA Rating: AW-PG-65YFW 400 TU4\" deep thermally broken fixed window Thermal (AAMA 1503 & CRFf of 69for 1\" insulating glass. NFRC 102): U-Value of 0.41 btu/hr/ft²/°F or lessYFW 400 TUH ASTM E 90 & ASTM E 1332: 35 STC, 28 OITC(Florida High Velocity Hurricane Zone Approved) Air (ASTM E 283): 0.10 cfm/ft² @ 1.57 psf4\" deep thermally broken, impactresistant and blast mitigating fixed Water (ASTM E 331): 15.0 psfwindow for 1” insulating glass. AAMA/WDMA Rating: AW-PG100-FW Thermal (AAMA 1503 & CRFf of 67 NFRC 100): U-Value of 0.41 btu/hr/ft²/°F or less ASTM E 90 & ASTM E 1332: 38 STC, 30 OITC Air (ASTM E 283): 0.10 cfm/ft² @ 1.57 psf Water (ASTM E 331): 15.0 psf AAMA/WDMA Rating: AW-PG100-FW (ASTM E 1886 / 1996, TAS 201 – 203): + 90 / -120 psf Thermal (AAMA 1503 & CRFf of 67 NFRC 100): U-Value of 0.41 btu/hr/ft²/°F or less ASTM E 90 & ASTM E 1332: 38 STC, 30 OITC ASTM F 1642: Wet Glazed-Minimal Hazard GSA-TS01: Wet Glazed-Level 2YOW 225 AAMA/WDMA Rating: AW-60 Operable, AW-100 Fixed2-1/2\" deep operable and fixed window Thermal (AAMA 1503 & CRFf of 30system for 1/4\" monolithic, and 1\" NFRC 100): U-Value of 0.47 btu/hr/ft²/°F or lessinsulating glass. ASTM E 90 & ASTM E 1332: 32 STC, 26 OITC 1\" IGU annealedYOW 225 H Air (ASTM E 283): 0.10 cfm/ft² @ 1.57 psf(Florida High Velocity Hurricane Zone Approved) Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixed2-1/2\" deep impact resistant operable AAMA/WDMA Rating: AW-65 Operableand fixed window system for 9/16\"monolithic glass. AW-100 Fixed (ASTM E 1886 / 1996, ± 65 psf Operable TAS 201 – 203): + 70 / -90 psf Fixed (Large Missile) ± 100 psf Fixed (Small Missile) ASTM E 90 & ASTM E 1332: 32 STC, 26 OITCEffective Date: May 3, 2013 | PS-1000-05 Certified test reports are available at www.ykkap.com/productmaster Page-25

Product Selection Guide OPERABLE WINDOWS – PRODUCT COMPARISONYKK AP PRODUCT EFCO KAWNEER OLD CASTLE US ALUMINUM BUILDING ENVELOPEYOW 225 TU Series 511 8225TL 40P/78P Series 7200/7300Thermally Broken Operable andFixed Window for Insulating GlassYOW 225 TUH — — ——Thermally Broken Operable and —Fixed Window for Insulating Glass 8225TLYOW 250 T Series 510-I (TS) 8325TL 12E/25E Series 7400Thermally Broken Operable andFixed Window for Insulating GlassYOW 350 T — ——Thermally Broken Heavy WallOperable and Fixed Window forMonolithic and Insulating GlassYOW 350 XT — AA900 ISOWEB® — —Thermally Broken Operable andFixed Window for Insulating GlassPage-26 PS-1000-05 | Effective Date: May 3, 2013

Product Selection GuideOPERABLE WINDOWS – PERFORMANCE BY SYSTEMYOW 225 TU Air (ASTM E 283): 0.10 cfm/ft² @ 6.24 psf2-1/4\" deep thermally broken operable Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixed AAMA/WDMA Rating: AW-65 Operableand fixed window system for 1\" AW-100 Fixed Thermal (AAMA 1503 & CRFf of 55 Operable, 57 Fixedinsulating glass. NFRC 100): U-Value of 0.52 btu/hr/ft²/°F or less (Operable) U-Value of 0.39 btu/hr/ft²/°F or less (Fixed) ASTM E 90 & ASTM E 1332: 34 STC, 27 OITC Operable 32 STC, 27 OITC Fixed Air (ASTM E 283): 0.10 cfm/ft² @ 6.24 psfYOW 225 TUH Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixed(Florida High Velocity Hurricane Zone Approved) AAMA/WDMA Rating: AW-65 Operable2-1/4\" deep impact resistant and blast AW-100 Fixedmitigating thermally broken operableand fixed window system for 1\" (ASTM E 1886 / 1996, ± 65 psf Operableinsulating glass. TAS 201 – 203): + 70 / -90 psf Fixed (Large Missile)YOW 350 T3-1/2\" deep thermally broken, heavy ± 100 psf Fixed (Small Missile)wall window for 1/4\" monolithic or 1\"insulating glass, with standard or triple Thermal (AAMA 1503 & CRFf of 55 Operable, 57 Fixedglazing options. NFRC 102): U-Value of 0.52 btu/hr/ft²/°F or less (Operable) U-Value of 0.39 btu/hr/ft²/°F or less (Fixed) ASTM E 90 & ASTM E 1332: 34 STC, 27 OITC (Operable) 32 STC, 27 OITC (Fixed) ASTM F 1642: Wet or Dry Glazed-Low Hazard GSA-TS01: Wet or Dry Glazed-Level 3B Air (ASTM E 283): 0.10 cfm/ft² @ 6.24 psf Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixed AAMA/WDMA Rating: AW-80 Operable AW-100 Fixed Thermal (AAMA 1503 & CRFf of 50 Operable, 63 Fixed NFRC 102): Standard Glazing U-Value of 0.53 btu/hr/ft²/°F or less (Casement) U-Value of 0.53 btu/hr/ft²/°F or less (Project) U-Value of 0.37 btu/hr/ft²/°F or less (Fixed) Triple Glazing U-Value of 0.45 btu/hr/ft²/°F or less (Casement) U-Value of 0.44 btu/hr/ft²/°F or less (Project) U-Value of 0.32 btu/hr/ft²/°F or less (Fixed)YOW 350 XT Air (ASTM E 283): 0.10 cfm/ft² @ 6.24 psf3-1/2\" deep “Best in Class Performance”thermally broken, state of the art energy Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixedperformance window for 1\" insulatingglass. AAMA/WDMA Rating: AW-80 Operable AW-100 Fixed Thermal (AAMA 1503 & CRFf of 68 NFRC 100): U-Value of 0.35 btu/hr/ft²/°F or less (Operable) U-Value of 0.34 btu/hr/ft²/°F or less (Fixed) ASTM E 90 & ASTM E 1332: 34 STC, 27 OITC Operable 32 STC, 27 OITC FixedEffective Date: May 3, 2013 | PS-1000-05 Certified test reports are available at www.ykkap.com/productmaster Page-27

Product Selection Guide OPERABLE WINDOWS – PRODUCT COMPARISONYKK AP PRODUCT EFCO KAWNEER OLD CASTLE US ALUMINUM BUILDING ENVELOPEYSW 400 T Series 6555 8470TL — —Thermally Broken Sliding Window Non-Impactfor Monolithic and Insulating GlassYVS 400 TU Series 680/690 8430TL 57P —Thermally Broken Single and Non-Impact 57P — — —Double Hung Window for InsulatingGlassYVS 410 TU Series 670-675 8450TLThermally Broken Single and Non-ImpactDouble Hung Window for Insulating Series 663Glass Impact Grade 8450TLYVS 410 TUHThermally Broken Impact ResistantSingle and Double Hung Windowfor Insulating GlassPage-28 PS-1000-05 | Effective Date: May 3, 2013

Product Selection GuideOPERABLE WINDOWS – PERFORMANCE BY SYSTEMYSW 400 T Air (ASTM E 283): 0.30 cfm/ft² @ 1.57 psf4\" deep thermally broken horizontal Water (ASTM E 331): 9.0 psfsliding window for 1\" insulating glass. AAMA/WDMA Rating: HS-AW-40 Thermal (AAMA 1503 & CRFf of 55 NFRC 102): U-Value of 0.50 btu/hr/ft²/°F ASTM E 90 & ASTM E 1332: 33 STC, 28 OITCYVS 400 TU Air (ASTM E 283): 0.30 cfm/ft² @ 6.24 psf4\" deep thermally broken single ordouble hung tilt-in window for 1\" Water (ASTM E 331): 10.0 psfinsulating glass. AAMA/NAFS 101 Rating: AW-50YVS 410 TU4\" deep thermally broken single or Thermal (AAMA 1503 & CRFf of 51 Single Hung, 53 Double Hungdouble hung side-loaded window for 1\"insulating glass. NFRC 102): U-Value of 0.50 btu/hr/ft²/°F or less (Single)YVS 410 TUH U-Value of 0.53 btu/hr/ft²/°F or less (Double)(Florida High Velocity Hurricane Zone Approved) ASTM E 90 & ASTM E 1332: 30 STC, 23 OITC Single Hung4\" deep thermally broken, impact 31 STC, 24 OITC Double Hungresistant and blast mitigating single ordouble hung side-loaded window for 1\" Air (ASTM E 283): 0.30 cfm/ft² @ 6.24 psfinsulating glass. Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixed AAMA/NAFS 101 Rating: AW-65 Thermal (AAMA 1503 & CRFf of 51 Single Hung, 53 Double Hung NFRC 102): U-Value of 0.50 btu/hr/ft²/°F or less (Single) U-Value of 0.53 btu/hr/ft²/°F or less (Double) ASTM E 90 & ASTM E 1332: 30 STC, 23 OITC Single Hung 31 STC, 24 OITC Double Hung Air (ASTM E 283): 0.30 cfm/ft² @ 6.24 psf Water (ASTM E 331): 12.0 psf Operable, 15 psf Fixed AAMA/WDMA Rating: AW-65 (ASTM E 1886 / 1996, TAS 201 – 203): + 80 / -120 psf Thermal (AAMA 1503 & CRFf of 54 NFRC 102): U-Value of 0.49 btu/hr/ft²/°F or less ASTM E 90 & ASTM E 1332: 36 STC, 22 OITC ASTM F 1642: Wet Glazed-Minimal Hazard GSA-TS01: Wet Glazed- Level 3bEffective Date: May 3, 2013 | PS-1000-05 Certified test reports are available at www.ykkap.com/productmaster Page-29



ENTRANCES



Table of ContentsENTRANCESEntrance Hardware20 D / 35 D / 50 D25 FD35 H / 50 H35 HL / 50 HL35 XT / 50 XT40 M / 50 M



Entrance Hardware



Entrance Hardware TABLE OF CONTENTSENTRANCE HARDWARE LOCATION .............................................. Page 2 to 4PULL/PUSH BAR ............................................................................... Page 5PIVOTS & HINGES ............................................................................. Pages 6 to 11LOCKING DEVICES ........................................................................... Pages 12 to 14PANIC DEVICES ................................................................................ Pages 15 to 17REMOVABLE MULLIONS .................................................................. Page 18 to 19CLOSERS ........................................................................................... Pages 20 to 21THRESHOLD & WEATHER STRIPPING ........................................... Page 22Effective Date: November 15, 2016 | 01-1008-02 Page-1

Entrance Hardware DOOR OPENING CLEARANCE STANDARD ENTRANCE HARDWARE LOCATIONNOTE: All dimensions shown are for actual door leaf. Standard floor clearance = 11/16\". Clearance plus hardware location dimensions = height above finished floor. May vary by door bottom clearance requirements.Page-2 01-1008-02 | Effective Date: November 15, 2016

Entrance HardwareSTANDARD ENTRANCE HARDWARE LOCATION NOTE: All dimensions shown are for actual door leaf.OPTIONAL ENTRANCE HARDWARE LOCATIONEffective Date: November 15, 2016 | 01-1008-02 Page-3

Entrance Hardware OPTIONAL ENTRANCE HARDWARE LOCATION Continuous Hinge MS Hookbolt Lock with Thumbturn YKK AP Smart Series Push/Pull Select® SL27HD (35H Door) Roton® 780-226HD (35H, 40M/50M Doors) Roton® 780-224HD (20D/35D/50D Doors) Roton® 780-111HD (35XT/50XT Doors)NOTE: All dimensions shown are for actual door leaf. Standard floor clearance = 11/16\". Clearance plus hardware location dimensions = height above finished floor. May vary by door bottom clearance requirements.Page-4 01-1008-02 | Effective Date: November 15, 2016

Entrance HardwareH-1141 STANDARD – SMART SERIES PULL/PUSH BAR PULL HANDLE Description: 1. Innovatively styled extruded aluminum 1\" diameter canted offset pull with 9\" O.C. mounting. The open style assists handicapped access and permits easy access to the lock cylinder. Finish: 628 Clear, 335 Black, 612* (US 10), 613* (US 10B), 629* (US 32), & 630* (US 32D) PUSH BAR Description: 1. The YKK AP SmartPush is a truly innovative 1\" diameter push bar designed to help ensure the safety of building occupants. The unique design subtly directs the user to push on the correct side of the door so as not to impede egress from the building.** Finish: 628 Clear, 335 Black, 612* (US 10), 613* (US 10B), 629* (US 32), & 630* (US 32D) For use with: All YKK AP entrances. * Non-Stock Item ** Minimum door width for this item is 27\".H-1104 OPTIONAL – 1\" DIAMETER PULL/PUSH BAR PULL HANDLE Description: 1. Contemporary styled extruded aluminum 1\" diameter 90 degree offset pull with 9\" O.C. mounting; pull projection 3-1/2\" from door face. Mounting is concealed type or thru-bolt. Finish: 628 Clear, 335 Black, 612* (US 10), 613* (US 10B), 629* (US 32), & 630* (US 32D) PUSH BAR Description: 1. Contemporary styled extruded aluminum 1\" diameter push bar bent at each end; bar projection approximately 2-1/2\" from door face. Mounting is concealed type. Finish: 628 Clear, 335 Black, 612* (US 10), 613* (US 10B), 629* (US 32), & 630* (US 32D) For use with: All YKK AP entrances. * Non-Stock ItemEffective Date: November 15, 2016 | 01-1008-02 Page-5

Entrance HardwareH-2101 (RH) STANDARD – OFFSET PIVOT PACKAGE – Includes:H-2102 (LH) Offset Pivot TOP PIVOT Description: 1. Door and frame portion of top pivot assembly are die cast aluminum. 2. Press fit bearing on frame portion is self-lubricating oilite bronze type. 3. Spring loaded hardened steel dowel pivot pin in door portion completes assembly. BOTTOM PIVOT Description: 1. Door portion; Cast aluminum with radial and thrust ball-bearings; with vertical screw adjustment. 2. Frame portion (with threshold): Cast aluminum pivot base with steel pivot; integral part of door frame and securely anchors frame and threshold to floor. 3. Frame portion (without threshold): Stainless steel pivot plate with stainless pivot; plate fastened at three points directly to floor. Finish: Electrodeposition coating in aluminum or black to match Anodized Plus®. Application: 1. Top offset pivot: Mortised frame portion into header/ transom bar, attached with screws through extrusion and threaded into pivot block. Spring loaded pivot allows for easy installation and maintenance. 2. Bottom offset pivot: Frame portion is used with threshold. On interior or vestibule doors not requiring threshold, floor mounted portion is used. Door portion provides vertical adjustment with both pivot pieces. 3. Typical package for doors up to 7'- 6\" height; requires intermediate pivot for doors over 7'- 6\" high. 4. Intermediate pivot can be specified for doors to 7'-0\" height. For use with: Models 20D/35D/50D and 35XT/50XT.H-2201 (RH) OPTIONAL STANDARD – INTERMEDIATE OFFSET PIVOTH-2202 (LH) Intermediate Pivot Description: 1. Aluminum pivot is fully mortised into door and frame with 3/4\" offset from door face. 2. Full race ball bearing and oilite bushing; bearing is corrosion resistant and self lubricating. Pin fully retractable for ease of installation and vertical adjustment. Finish: Baked epoxy finish in aluminum or black. Application: 1. Use in conjunction with offset pivot package for additional strength and door/frame alignment. 2. Use on doors experiencing high traffic volume or on doors exceeding 7'-6\" high. 3. Use with offset pivot package only; doors over 7'-6\" require intermediate pivot. 4. Intermediate pivot can be specified for doors to 7'-0\" height. 5. Intermediate pivot is additional cost item. For use with: Models 20D/35D/50D and 35XT/50XT.Page-6 01-1008-02 | Effective Date: November 15, 2016

Entrance Hardware HEAVY DUTY – OFFSET PIVOT PACKAGE – Includes TOP PIVOT Description: 1. Door and frame portion made of forged bronze. 2. Frame portion constructed with a bronze oilite bearing. 3. Pivot pin is hardened steel and treated to prevent rusting. Parco-lubricated. 4. Grade 1.P-21111 (RH) BOTTOM PIVOTP-22112 (LH)Heavy Duty Offset Pivot Package Description: 1. Door portion is heavy duty steel with arm cap.145” - Model 35H 2. Frame portion is brass. Floor mounted for maximum strength. 3. Grade 1. Finish: Exposed surfaces can be US26D, US26, US10, and/or US10B. Application: 1. Top pivot: Mortised into header/transom bar. Door portion is applied to interior door web for added strength. 2. Bottom pivot: Door portion is mounted directly into door web. 3. The use of these pivots is primarily for high frequency and/or where extra strength is required. YKK AP recommends the use of at least one (1) intermediate offset pivot when specifying the Heavy Duty Pivot Packages. For use with: Models 20D/35D/50D, 40M/50M, 35XT/50XT, and 35H.P22101 (RH) HEAVY DUTY – INTERMEDIATE OFFSET PIVOTP22102 (LH)Heavy Duty Intermediate Pivot Description: 1. Made of forged bronze. Corrosion resistant, self-lubricating thrust bearing with a hardened Parco-Lubricated steel pivot pin. 2. Grade 1. Finish: 628 Clear, 335 Black, US26D, US26, US10, and/or US10B. Application: 1. Use in conjunction with Heavy Duty Pivot package to provide maximum strength and door/frame alignment. 2. Should be used on all applications requiring the use of 40M/50M Monumental type doors and/or use of Heavy Duty pivots. 3. Pivot is fully mortised into both door and frame. 4. Back-up or reinforcing plates are used in both door hinge stile and frame hinge jamb. For use with: Models 20D/35D/50D, 40M/50M, 35XT/50XT, and 35H.Effective Date: November 15, 2016 | 01-1008-02 Page-7

Entrance Hardware H-2111 OFFSET PIVOT – FRAME PORTION FOR NO THRESHOLD Offset Pivot for No Threshold APPLICATIONS Applications Description:E1-0387Pivot Shim 1. Cast stainless steel pivot base securely anchors pivot at three points directly to the floor. H-2401 Top Center Pivot 2. Designed to work with the standard offset pivot door portion. H-2501 Bottom Center Pivot Finish:Page-8 Mill finish. For use with: Models 20D/35D/50D, 35XT/50XT, 35H, and 25FD. PIVOT SHIM Description: 1. Solid machined aluminum shim for use with H-2111. Finish: Mill finish. For use with: Models 35XT/50XT. Optional for all other YKK AP entrances. STANDARD – CENTER PIVOT Description: 1. Cast aluminum “Walking Beam Type” frame pivot portion with hardened steel pivot pin for additional extension through transom bar/header. 2. Door pivot portions are machined aluminum with oilite bronze self-lubricating bearings; top center hung pivot parts are concealed. Finish: Frame portion is natural cast aluminum; machined door portion is mill finish. Application: 1. Use in conjunction with center hung doors with floor closers. 2. Use top and bottom center pivots with surface mounted closer or top pivot only with floor closer. For use with: Models 20D/35D/50D, 40M/50M, and 35XT/50XT. STANDARD – BOTTOM CENTER PIVOT Description: 1. Frame portion (with or without threshold): Extruded machined aluminum with adjustable pin. 2. Threshold portion: Ball bearing, adjustable pivot pin. 3. Without threshold: Stainless steel pivot pin; not adjustable in the pivot housing. 4. Door portion: Steel clamping bolt threaded into cast aluminum pivot block. Finish: Mill finish. Application: 1. Entrances with thresholds: Pivot is anchored to frame and threshold. This frame portion has an adjustable pin for proper door and frame clearance. 2. Entrances without thresholds: Frame portion is securely fastened to frame and directly to floor. 3. Use top and bottom center pivots with surface mounted closer or bottom pivot only with concealed overhead closer. For use with: Models 20D/35D/50D, 40M/50M, and 35XT/50XT. 01-1008-02 | Effective Date: November 15, 2016

P-1300-SS Butt Hinge Entrance Hardware STANDARD – BUTT HINGE, 4-1/ 2\" X 4\" Description: 1. Commercial quality five knuckle, two ball bearing raceway construction type stainless steel; enclosed hinge barrel with button tips incorporating non-rising removable steel pin. 2. Radius corner hinge. Standard template butt, 4-1/2\" X 4\" X 0.134\" thickness (114.3mm by 101.6mm by 3.4mm). 4. Tapped back-up reinforcing plates are provided for each hinge. Finish: Standard: Stainless Steel for clear anodized. Optional: 335 Black finish for color anodized and/or painted finished. Application: 1. Butt hinge fully mortised into door hinge stile and frame hinge jamb. 2. Back-up or reinforcing plates are used in both frame jamb and hinge stile. 3. Use intermediate butt (1-1/2 pair per leaf) for doors in high traffic areas or for doors over 7'-6\" high. For use with: Models 20D/35D/50D, 35XT/50XT, 35H (optional), and 25FD.P-1303 Heavy Duty Butt Hinge HEAVY DUTY – BUTT HINGE, 4 -1/ 2\" X 4 -1/ 2\" Description: 1. Grade 1 heavy weight quality. Five knuckle, four ball bearing brass with stainless steel pin. Testing in conformance with ANSI-A156.1-81. 2. Pin is non-rising with optional non-removable (NRP) pin available. 3. Radius corner (RC) hinge. 4-1/2\" x 4-1/2\" x 0.180\" thickness (114.3mm by 114.3mm by 4.6mm) 4. Tapped back-up reinforcing plates are provided for each hinge. Finish: 628 Clear, for clear anodized or painted surfaces or 335 Black, finish for color anodized and/or painted finished. Application: 1. Hinge is fully mortised into door hinge stile and frame hinge jamb. On 40M/50M Monumental doors hinge is mortised into the frame, but requires no backer plate for extra strength. 2. Back-up or reinforcing plates are used whenever mortising of hinge is required. 3. Intermediate hinge is standard on all 40M/50M Monumental entrances and recommended on all high traffic applications. Doors over 7'-6\" in height also require the use of intermediate hinges. For use with: Models 40M and 50M. Optional for Models 20D/35D/50D, 35XT/50XT, 35H, and 25FD.Effective Date: November 15, 2016 | 01-1008-02 Page-9

Entrance Hardware HEAVY DUTY – CONTINUOUS HINGE Description: 1. Select® SL 27HD continuous geared aluminum hinge. 2. Continuous geared hinges use a rotating joint to minimize lateral wear on the hinge while evenly distributing door weight along the full length of the frame. 3. Hinge Stile includes mortised edge to allow standard glass formulas to be used. Finish: 628 Clear, for clear anodized or painted surfaces or 335 Black, finish for color anodized and/or painted finished. Application: 1. Hinge Stile includes mortised edge to allow standard glass formulas to be used. For use with: Model 35H.P-26103 Continuous Hinge HEAVY DUTY – CONTINUOUS HINGE Description: 1. Roton® 780-226HD continuous geared aluminum hinge . 2. Continuous geared hinges use a rotating joint to minimize lateral wear on the hinge while evenly distributing door weight along the full length of the frame. Finish: 628 Clear, for clear anodized or painted surfaces or 335 Black, finish for color anodized and/or painted finished. Application: 1. Hinge Stile includes mortised edge to allow standard glass formulas to be used. For use with: Models 40M/50M and 35H.P-26014 Continuous HingePage-10 01-1008-02 | Effective Date: November 15, 2016

Entrance Hardware STANDARD HEAVY DUTY – CONTINUOUS HINGE Description: 1. YKK AP Standard continuous geared aluminum hinge. 2. Continuous geared hinges use a rotating joint to minimize lateral wear on the hinge while evenly distributing door weight along the full length of the frame. Finish: 628 Clear, for clear anodized or painted surfaces or 335 Black, finish for color anodized and/or painted finished. Application: 1. Active leg of Hinge Stile wraps door stile for greater strength. Specific glass formulas required. For use with: Models 20D/35D/50D, and 25FD.H-20100 Continuous Hinge HEAVY DUTY – CONTINUOUS HINGE Description: 1. P-26005 continuous geared aluminum hinge. 2. Continuous geared hinges use a rotating joint to minimize lateral wear on the hinge while evenly distributing door weight along the full length of the frame. 3. Hinge Stile includes mortised edge to allow standard glass formulas to be used. Finish: 628 Clear, for clear anodized or painted surfaces or 335 Black, finish for color anodized and/or painted finished. Application: 1. Hinge Stile includes mortised edge to allow standard glass formulas to be used. For use with: Models 35XT and 50XT.P-26005 Continuous HingeEffective Date: November 15, 2016 | 01-1008-02 Page-11

Entrance Hardware STANDARD – HOOKBOLT Description: 1. Adams-Rite® MS 1853A-050 series Hookbolt with five ply laminated steel hookbolt; non-handed. 2. Standard backset is 1-1/8\" (narrow stile door) or 1-1/2\" (medium & wide stile doors). 3. Assembly accepts any standard 1-5/32\" diameter mortised cylinder, thumbturn cylinder, or dummy cylinder. All operating cylinder types require MS cam. 4. Requires faceplate on single door. 5. Considered maximum security for YKK AP standard and upgrade locking devices.H-3201 (1-1/8\" backset) For use with: Model 20D.H-3202 (1-1/2\" backset) For use with: Models 35D, 50D, 40M, 50M, 35XT, 50XT, and 35H.Hookbolt with Strike H-3401 (RH) OPTIONAL – DEADLATCH H-3402 (LH) Lever Handle Description: 1. Adams-Rite® Series 4510 Deadlatch. 2. Standard backset is 1-1/8\" (narrow stile door) or 1-1/2\" (medium & wide stile doors). 3. Assembly accepts any standard 1-5/32\" diameter mortised cylinder, thumbturn cylinder, or dummy cylinder. All operating cylinder types require MS cam. 4. Assembly accepts Adams-Rite 4560 Lever Handle. 5. Requires faceplate and Adams-Rite 4502 Strike.H-3205 (RH) For use with: Model 20D.H-3206 (LH)Latch Lock (1-1/8\" backset)H-3207 (RH)H-3208 (LH)Latch Lock (1-1/2\" backset)Page-12 01-1008-02 | Effective Date: November 15, 2016

Entrance HardwareH-4202 H-4204 STANDARD – CYLINDERS5-Pin Cylinder Thumbturn Cylinder Description: 1. 5 Pin - mortised, 1-5/32\" (29.4mm) diameter.H-4205 2. Standard cylinders are key operated on the exterior and thumbturnDummy Cylinder operated on the interior. 3. Blank cylinders available as an option. H-4206 4. Keyed alike cylinders are available, when specified. Cylinder Guard 5. Master keying and special order keying systems are special order; contact factory. Finish: Cylinder caps are either 628 Clear, for clear anodized or painted surfaces or 335 Black, finish for color anodized and/or painted finished.. OPTIONAL – CYLINDER GUARD Description: 1. Adams-Rite® MS 4043 Cylinder Guard; tapered and hardened steel material collar with hardened steel retainer plate. 2. Cylinder guard is collar designed to protect the vulnerable soft brass cylinder. Guard held in place with hardened steel retainer plate for additional security. Application: Use with Adams-Rite MS 1850A, MS 1853A-050 or deadlatch series. For use with: All YKK AP entrances. STANDARD – FLUSHBOLT Description: Inactive leaf on door pairs: 1. Top and bottom bolts in inactive leaf provide two lock points allowing active door leaf to lock into inactive leaf. 2. Flush bolts are flush mounted in door stile “edge.” Finish: Black for color anodized finishes and aluminum color for clear anodized finishes. For use with: All YKK AP entrances. H-4101 FlushboltEffective Date: November 15, 2016 | 01-1008-02 Page-13

Entrance HardwareP-2101 Hook Lock STANDARD – THREE POINT LOCK 1-1/2\" Backset Description: Single 35H entrance doors, non-emergency egress, P-2242 Threshold Bolt employ a three point locking system to ensure that they remain secured during the strong cyclical winds associated with hurricanes. The three point locking system features a single actuation system for ease of use, keyed exterior cylinder, and interior thumbturn. For use with: All YKK AP entrances. H-3211 Header Bolt P-2101 Hook Lock HEAVY DUTY – FIVE POINT LOCK 1-1/2\" Backset Description: Pairs of 35H entrance doors, non-emergency egress, P-2242 Threshold Bolt employ a five point locking system to ensure that they remain secured during the strong cyclical windsPage-14 associated with hurricanes. The active leaf employs a three-point locking system that features a single actuation system for ease of use, keyed exterior cylinder, and interior thumbturn. The inactive leaf utilizes a two point locking system that is activated by an interior thumbturn. For use with: Model 35H. P-2151 Two-Point Lock H-3211 Header Bolt 01-1008-02 | Effective Date: November 15, 2016

Entrance Hardware P-52497 Concealed Panic Device STANDARD – PANIC DEVICES P-52005 CONCEALED VERTICAL ROD Concealed Panic Device EO P-52094 Description: Concealed Panic Device NL-OP 1. Concealed Panic Device has concealed vertical lock rods and top P-52107 latch mechanism in door stile. Concealed Panic Device EO 2. Depressing touchpad retracts the bottom rod from threshold and P-52150 Concealed Panic Device NL-OP releases top latch from transom bar/header mounted barrel strike. 3. Upon closing, top latch re-engages strike securely and frees bottom bolt toEffective Date: November 15, 2016 | 01-1008-02 engage threshold. Door is then locked from exterior. 4. Panic device can be deactivated or “dogged” with optional cylinder key or allen key in active housing. 5. Housings are cast aluminum with extruded aluminum touchpad. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; painted housing with anodized aluminum touch- pad. Other finishes available on special order; contact factory. Application: 1. Concealed vertical rod device eliminates removable mullion obstruction on pairs of doors. 2. Device when activated locks entrance on exterior and permits egress from building without the use of key. 3. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: Models 20D/35D/50D, 40M/50M, 35XT/50XT, and 35H. OPTIONAL – PANIC DEVICES CONCEALED VERTICAL ROD Description: 1. Von Duprin® Concealed Panic Devices have concealed vertical lock rods and top latch mechanism in door stile. 2. Depressing touchpad retracts the bottom rod from threshold and releases top latch from transom bar/header mounted barrel strike. 3. Upon closing, top latch re-engages strike securely and frees bottom bolt to engage threshold. Door is then locked from exterior. 4. Panic device can be deactivated or “dogged” with optional cylinder key or allen key in active housing. 5. Housings are cast aluminum with extruded aluminum touchpad. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; anodized aluminum housing and touchpad. Other finishes available on special order; contact factory. Application: 1. Concealed vertical rod device eliminates removable mullion obstruction on pairs of doors. 2. Device when activated locks entrance on exterior and permits egress from building without the use of key. 3. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: Models 20D/35D/50D, 40M/50M, 35XT/50XT. Page-15

Entrance HardwareP-54453 Rim Panic Device STANDARD – PANIC DEVICES RIM TYPE Description: 1. Rim Panic Device has latch bolt in rim of active housing engaging adjustable roller strike to provide locking action. 2. Depressing touchpad “unlocks” the device and permits egress. The bolt re-engages the strike and locks when the door closes. 3. On single doors, adjustable strike is mounted on frame lock jamb. Adjustable strike is part of removable mullion required for door pairs. 4. Panic device can be deactivated “dogged” with cylinder key or allen key. Keyed alike cylinders are optional. 5. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; painted housing with anodized aluminum touchpad. Other finishes available on special order; contact factory. Application: 1. Depressing touchpad permits egress from building without key. 2. Removable mullion is required on pairs of doors. Using optional mullion stabilizers is recommended. 3. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: Model 20D/35D/50D, 40M/50M, 35XT/50XT,and 25FD. P-54007 OPTIONAL – PANIC DEVICES Rim Panic Device EO P-54004 RIM TYPE Rim Panic Device NL-OP Description: P-54108 1. Von Duprin® Rim Panic Devices have latch bolt in rim of active Rim Panic Device EO P-54109 housing engaging adjustable roller strike to provide locking action. Rim Panic Device NL-OP 2. Depressing touchpad “unlocks” the device and permits egress. The boltPage-16 re-engages the strike and locks when the door closes. 3. On single doors, adjustable strike is mounted on frame lock jamb. Adjustable strike is part of removable mullion required for door pairs. 4. Panic device can be deactivated “dogged” with cylinder key or allen key. Keyed alike cylinders are optional. 5. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; anodized aluminum housing and touchpad. Other finishes available on special order; contact factory. Application: 1. Depressing touchpad permits egress from building without key. 2. Removable mullion is required on pairs of doors. Using optional mullion stabilizers is recommended. 3. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: P-54007 & P-54004 - All YKK AP entrances. P-54108 & P-54109 - Model 50D, 50XT, 35H & 25FD. 01-1008-02 | Effective Date: November 15, 2016

P-55215 Mid Rail Panic Device Entrance Hardware OPTIONAL – MID RAIL PANIC DEVICE CONCEALED VERTICAL ROD Description: 1. Concealed vertical rod with top and bottom (two point) vertical locking rods concealed in door stiles. 2. Depressing the operating panel at any point retracts the bottom rod from threshold and releases the top latch from the transom bar/header mounted strike. 3. Upon closing, top latch re-engages strike securely and frees the bottom bolt to engage the threshold. Door is then locked from the exterior. 4. Panic device can be de-activated or “dogged” with allen key at the locking stile at the end of the operating panel. 5. Housing is a single aluminum extrusion 8-3/4”\"(222.3mm) in height including glass stops for 1/4\" glass, Rim cylinder diameter is 1-5/32\" (29.4mm). Housing is pinned and welded into place for added strength. 6. Projection of operating panel is approximately 1\" (25.4mm) in locked position and 1/2\" (12.7mm) when “dogged.” 7. Panic mechanism is concealed in door cross rail extrusion. Finish: Operating panel is clear or black anodized aluminum. Cross rail is finished to match door. For use with: Model 20D/35D/50D, 40M/50M, and 35H. STANDARD – PANIC PULL Description: Innovatively styled extruded aluminum 1\" diameter canted offset pull with 9\" O.C. mounting. The open style assists handicapped access and permits easy access to the lock cylinder. Finish: Clear or black anodized finish. H-1541 Panic Pull Page-17Effective Date: November 15, 2016 | 01-1008-02

Entrance Hardware H-5902 STANDARD – REMOVABLE MULLION Description: 1. YKK AP Removable Aluminum Mullion. 2. Depressing touchpad “unlocks” the device and permits egress. The bolt re-engages the strike and locks when the door closes. 3. On single doors, adjustable strike is mounted on frame lock jamb. Adjustable strike is part of removable mullion required for door pairs. 4. Panic device can be deactivated “dogged” with cylinder key or allen key. Keyed alike cylinders are optional. 5. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; painted housing with anodized aluminum touchpad. Other finishes available on special order; contact factory. Application: 1. Removable mullion is required on pairs of doors. Using optional mullion stabilizers is recommended. 2. Touchpad design offers increased building security and reduces the risk of code infringements. 3. Steel reinforcement required for use with Model 35H. For use with: All YKK AP entrances.Falcon™ (Dor-O-Matic®) P56410 OPTIONAL – REMOVABLE MULLION Description: 1. Falcon™ (Dor-O-Matic®) P56410 Removable Aluminum Mullion. 2. Depressing touchpad “unlocks” the device and permits egress. The bolt re-engages the strike and locks when the door closes. 3. On single doors, adjustable strike is mounted on frame lock jamb. Adjustable strike is part of removable mullion required for door pairs. 4. Panic device can be deactivated “dogged” with cylinder key or allen key. Keyed alike cylinders are optional. 5. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; painted housing with anodized aluminum touchpad. Other finishes available on special order; contact factory. Application: 1. Removable mullion is required on pairs of doors. Using optional mullion stabilizers is recommended. 2. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: All YKK AP entrances.Page-18 01-1008-02 | Effective Date: November 15, 2016

Entrance HardwareFalcon™ (Dor-O-Matic®) H-5601 / H-5602 OPTIONAL – REMOVABLE MULLION Description: 1. Falcon™ (Dor-O-Matic®) H-5601 / H-5602 Removable Aluminum Mullions. 2. Depressing touchpad “unlocks” the device and permits egress. The bolt re-engages the strike and locks when the door closes. 3. On single doors, adjustable strike is mounted on frame lock jamb. Adjustable strike is part of removable mullion required for door pairs. 4. Panic device can be deactivated “dogged” with cylinder key or allen key. Keyed alike cylinders are optional. 5. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; painted housing with anodized aluminum touchpad. Other finishes available on special order; contact factory. Application: 1. Removable mullion is required on pairs of doors. Using optional mullion stabilizers is recommended. 2. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: All YKK AP entrances.Von Duprin #4954 OPTIONAL – REMOVABLE MULLION Description: 1. Von Duprin® #4954 Removable Steel Mullion. 2. Depressing touchpad “unlocks” the device and permits egress. The bolt re-engages the strike and locks when the door closes. 3. On single doors, adjustable strike is mounted on frame lock jamb. Adjustable strike is part of removable mullion required for door pairs. 4. Panic device can be deactivated “dogged” with cylinder key or allen key. Keyed alike cylinders are optional. 5. Rim cylinder diameter of 1-5/32\" (29.4mm); cylinder specified above. Finish: Clear and black; painted housing with anodized aluminum touchpad. Other finishes available on special order; contact factory. Application: 1. Removable mullion is required on pairs of doors. Using optional mullion stabilizers is recommended. 2. Touchpad design offers increased building security and reduces the risk of code infringements. For use with: Model 50D, 50M, 50XT, and 25FD entrances.Effective Date: November 15, 2016 | 01-1008-02 Page-19

Entrance HardwareH-6100 Series Surface Mounted Closer STANDARD – SURFACE MOUNTED CLOSERS Description: 1. Full rack and pinion type with cast aluminum body using non-gumming and non-freezing hydraulic fluid. Closer has two valves, hex key operated to independently regulate closing and latching speeds. Adjustable backcheck is standard on all closers. Closer meets Federal Specs FF-H-121C. 2. Closers are non-handed with or without hold open arms (specify one). All mounting brackets are included. 3. Closers are U.L. listed and meet ANSI A117.1 standards. 4. Closers with optional adjustable spring power for opening force size settings 1 thru 4 are also available. Finish: Available in spray painted finish. Available colors are silver (aluminum) and dark bronze. For use with: Models 20D/35D/50D, 40M/50M, 35XT/50XT, and 25FD.H-6104 LCN-4040 Series STANDARD – SURFACE MOUNTED CLOSERSSurface Mounted Closer Description: 1. Full rack and pinion type with cast aluminum body using non-gumming and non-freezing hydraulic fluid. Closer shall have two valves, hex key operated to independently regulate closing and latching speeds. Adjustable backcheck is standard on all closers. Closer meets Federal Specs FF-H-121C. 2. Closers are non-handed with or without hold open arms (specify one). All mounting brackets are included. 3. Closers are U.L. listed and meet ANSI A117.1 standards. 4. Closers with optional adjustable spring power for opening force size settings 1 thru 4 are also available. Finish: Available in spray painted finish. Available colors are silver (aluminum) and dark bronze. For use with: Model 35H.Page-20 01-1008-02 | Effective Date: November 15, 2016

Entrance Hardware STANDARD – CONCEALED OVERHEAD CLOSERS Description: 1. Single and double acting non-handed concealed door closer. Closer fits 1-3/4\" x 4\" (44.5mm by 101.6mm) transom bar or header. Closers have 90 degree or 105 degree back stop with optional hold open device, (specify). 2. Closers are two speed type with factory preset closing speed and adjustable latching speed. 3. Closers are center pivoted type, single or double acting, or offset type for use with standard offset pivots or butt hinges. 4. Available with light and heavy duty spring and also with adjustable spring. Finish: Available in spray painted finish. Available colors are silver (alumi- num) and black.H-6209 thru 6212 Overhead ConcealedCloser for Center PivotFor use with: Models 20D/35D/50D and 40M/50M.H-6205 thru 6208 Overhead ConcealedCloser for Offset Pivot and Butt HingeFor use with: Model 20D/35D/50D, 40M/50M, 35XT/50XT, and 35H.Effective Date: November 15, 2016 | 01-1008-02 Page-21

Entrance Hardware THRESHOLDS Description: 1. Factory fabricated extruded aluminum; factory prepped for specified hinging and locking hardware; (specify). 2. Standard threshold: 4\" (101.6mm) wide x 1/2\" (12.7mm) high by width required. Finish: Mill finish. THRESHOLD STOP Description: Surface applied stop. Screw applied with gasket to 1/2\" (12.7mm) high threshold. Finish: Mill finish. WEATHER-STRIPPING BOTTOM DOOR SWEEPS Description: Extruded aluminum, surface applied weather-strip with elasto- mer sweep and concealed fasteners; applied to bottom interior door rail. Finish: Clear or black anodized finish. Painted finishes available to match door. Length: 3'-0\" to 4'-0\" H-7107 H-7107 (Finish Code) 0300 3'- 0\" H-7107 (Finish Code) 0400 4'- 0\" NOTE: Model 35XT and 50XT require sweeps at interior and exterior. Model 35H requires sweep at exterior for air and water threshold. BE9-1535Page-22 01-1008-02 | Effective Date: November 15, 2016

20D/35D/50D



20D/35D/50D Standard Entrance Framing Members TABLE OF CONTENTS 20D/35D/50D STANDARD ENTRANCESPRODUCT DATA........................................................................................ Page 2FRAMING MEMBERS (1/4 SIZE).............................................................. Pages 3 to 6*The latest installation instructions for this product are available at www.ykkap.com.Effective Date: September 15, 2016 | 01-1000-04 Page-1

> Model 20D/35D/50D Standard EntrancesEveryday Performance and StyleEntrance systems by YKK AP offer an abundance ofdesign options. VersaJamb®, our unique reinforcedtubular door frame, allows for side-lite glazing withoutshear clips while maintaining the structural integrityof transom frames.Door corners are mechanically joined and welded toensure that they are more than capable of withstandingtoday’s most demanding conditions. Standard hardwareoptions include the Smart Series Push/Pull and touch barexit devices. Custom entrances are availablewith options for one inch glazing, mid rails, highbottom rails and will accommodate most customhardware.20D/35D/50D Entrance Doors:YKK AP standard doors are far above standard qualityand performance. These institutional grade entrancesprovide complete design freedom via varied rail andstile widths. All door corners are mechanically joinedand welded — and carry a lifetime warranty.Entrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors









25FD



Model 25FD Flush Panel Swing Door TABLE OF CONTENTS 25FD FLUSH PANEL SWING DOORPRODUCT DATA........................................................................................ Page 2AVAILABLE CONFIGURATIONS.............................................................. Page 3PANEL COMPOSITION.............................................................................. Page 3DOOR OPTIONS......................................................................................... Page 4FRAMING MEMBERS (1/4 SIZE).............................................................. Pages 5 to 6EXIT DEVICE LOCATIONS........................................................................ Page 7*The latest installation instructions for this product are available at www.ykkap.com.Effective Date: September 15, 2016 | 01-1005-02 Page-1

> Model 25FD Flush Panel Entrance SystemDurability Performs BeautifullyYKK AP’s new flush panel entrance, Model 25FD, is available witha durable Fiber Reinforced Polyester resin (FRP) or an AluminumSkin to meet both aesthetic and performance requirements of anyproject. Marine Grade high compression honeycomb core materialprovides superior performance in compression strength. An aluminumskeleton in the form of a 4-1/2\" backup tube with a minimum 1/8\"wall thickness provides the strength necessary to resist abuse andmaintain the integrity of the door. This strong skeleton eliminates theneed for hardware specific reinforcement. Model 25FD is designedto accept a variety of locking and hinging hardware for security andegress applications.Product Benefits n Custom Entrance Sizes – Single Door up to 4'-0\" x 8'-0\" – Pair Doors up to 8'-0\" x 8'-0\" n 1-3/4\" Door panel will mount easily into YKK AP door frames n Locking hardware options include Rim Panics, Latch Locks, and Maximum Security Locks n Doors are available pre-glazed with 1/4\" monolithic or 1\" insulating glass n Aluminum louvers are available to meet project requirements n FRP panels are standard with a random pebble textured skin n Four standard colors are readily available – White, Grey, Dark Bronze, and Beige n Exterior Grade FRP skins provide superior resistance to fading n Aluminum skins available in Clear and Dark Bronze anodized finishesEntrances | Storefronts | Curtain Walls | Sun Controls | Windows | Balcony Doors

Model 25FD Flush Panel Swing Door AVAILABLE CONFIGURATIONSFull Flush Panel Half Vision Lite Classroom Vision Lite Small Vision LiteTop & Bottom Vision Lite Bottom Louver Small Bottom Louver Top Louver NOTE: Options shown above may be used in combination as needed. DOOR PANEL COMPOSITION AS-0421 AS-04214-1/2” [114.3mm] 4-1/4” Backup Tube with 1/8” Wall Thickness E9-1009 E1-1054 1-3/4” [44.5mm] 0.125” [3.18mm] Marine Grade 0.040” [1.02mm] Fiber Reinforced High Compression Smooth or Ribbed Polyester Panel Honeycomb Core Aluminum Skin Rotated 90° For IllustrationEffective Date: September 15, 2016 | 01-1005-02 0.085” [2.16mm] Glass Fiber Reinforced Polypropylene Substrate Page-3

Model 25FD Flush Panel Swing Door 7 8 DOOR OPTIONS 1 3 5 4 26SECTION 1 SECTION 3 SECTION 7 SECTION 4 SECTION 5 2-5/16” [59.2mm] SECTION 8 1-3/4\" SECTION 6 [44.5mm] 01-1005-02 | Effective Date: September 15, 2016 SECTION 2Page-4

Model 25FD Flush Panel Swing Door 1/4” GLAZING 9 10 5 7E1-1054 6 8 4 3 E9-1003SECTION 5 2 E9-0421 E9-0410 E9-0410 E9-0422 AS-0401 E9-0408 E9-0403 E9-1009 E9-0434 E9-0403AS-0402DOOR HEIGHT = D.0.H. -5/16 W/O THRESHOLD [D.O.H. -13/16 WITH THRESHOLD] SECTION 7 SECTION 9 SECTION 10 4” [101.6mm] AS-0421 AS-0421 E9-1009 E1-1054 SECTION 6 DOOR OPENING WIDTH = D.O.W. ÷ 2 - 3/8”OFFSET HUNG 1-3/4” [44.5mm] SECTION 3 SECTION 4 OFFSET HUNG OFFSET HUNG E9-0347 SECTION 8 E9-0348 MEETING STILE SECTION 2 SECTION 2 Page-5OFFSET HUNG OFFSET HUNG W/ BOTTOM RAIL WEATHER STRIPEffective Date: September 15, 2016 | 01-1005-02

Model 25FD Flush Panel Swing DoorE1-1054 1” GLAZING 9 10 5 4 7 6 38 E9-1013 SECTION 5 2E9-0413 AS-0451 E9-0410 E9-0410 AS-0452 E9-0453 AS-0401 E9-1012 E9-0435 E9-1356 SECTION 10DOOR HEIGHT = D.0.H. -5/16 W/O THRESHOLD [D.O.H. -13/16 WITH THRESHOLD] SECTION 7 E9-1358 4” [101.6mm] AS-0421 SECTION 9 E1-1054 AS-0451 E9-1012 SECTION 6 DOOR OPENING WIDTH = D.O.W. ÷ 2 - 3/8”OFFSET HUNG 2” [50.8mm] SECTION 3 SECTION 4 OFFSET HUNG OFFSET HUNG SECTION 2 E9-0347 SECTION 8 E9-0348 OFFSET HUNG MEETING STILE SECTION 2Page-6 01-1005-02 | Effective Date: September 15, 2016 OFFSET HUNG W/ BOTTOM RAIL WEATHER STRIP